GReddy Turbo Kit Bedienungsanleitung

GReddy Turbo Kit

2003 Nissan 350Z (VQ35DE) Twin TD05-18G 8cm2

Installation Manual

Please read the entire manual before installing this kit.

Application:

Make Model Chassis Year

Nissan 350Z Z33 2003

•This GReddy Turbo Kit is designed only for the vehicles specified above.

•GReddy Front mount intercooler kit is recommended with this kit

•Premium grade gasoline (91 octane or higher) is required with this Kit.

•Make sure that the vehicle is not equipped with any ECU upgrade chips.

•Use of GReddy Racing Spark Plugs ISO LONG #7 or NGK plugs (colder than

factory) is recommended with this kit.

Important

1. This installation should only be performed by a trained specialist who is very familiar with the

automobile’s mechanical, electrical and fuel management system.

2. If installed by an untrained person, it may cause damage to the kit as well as the vehicle.

3. GReddy Performance Products Inc. is not responsible for any damage to the vehicle’s electrical

system caused by improper installation.

4. Make sure to follow the instruction and pay attention to the “Important”, “Warning!” and “Caution!”

notice through out the instruction.

5. Improper installation can be dangerous! Please make sure to inspect the installation before

operating the vehicle.

6. Call your GReddy Authorized dealer or GReddy Performance Products if there are any problems or

questions regarding this product.

1. Parts List

1. Turbocharger TD05-18G 8cm22

2. Wastegate (GReddy / Tial) .45bar 2

3. Exhaust Manifold (Right Side) Ductile Iron Cast 1

4. Exhaust Manifold (Left Side) Ductile Iron Cast 1

5. Downpipe Adapter (Right Side) 1

6. Downpipe Adapter (Right Side) 1

7. Compression Pipe R C-1 (50∅Aluminum Elbow No.6) 1

8. “ R C-2 (50∅Aluminum) 1

9. “ R C-3 (50∅Aluminum Elbow No.21) 1

10. “ L C-4 (50∅-70∅Aluminum) 1

11. “ C-5 (50∅Aluminum) 1

12. “ C-6 (80∅Aluminum) 1

13. Airflow Meter Adapter 1

14. Suction Pipe R S-1 (60∅Aluminum) 1

15. “ R S-2 (70∅Aluminum) 1

16. “ L S-3 (60∅Aluminum Elbow No.82) 1

17. “ L S-4 (70∅Aluminum) 1

18.AirinxAY-SB(Blue) 2

19. Airinx Hose Adapter S70 2

20. Oil Pressure Hose SUS (R=600mm, L=800mm) _________________1 each

21. Oil Pressure Union Fitting 3-Way Fitting 2

22. “ 1/8PT – 1/8 PT Straight 2

23. “ 1/8PT – 1/8 PF Straight 1

24. “ 1/8PT – 1/8 PF Male to Male 90°1

25. Oil Pressure Banjo Fitting Male and Female (small) 2

26. Copper Washer 10∅(t=1.0) 4

27. Oil Return Pipe Right 16∅1

28. Oil Return Pipe Left 16∅1

29. Oil Pan with welded Oil Return Pipe 1

30. Vacuum Hose 5∅x 100mm (Blue) 1

31. “ 6∅x 2000mm (Blue) 1

32. Radiator Reserve Hose 7∅x 10∅x 790mm CR60°Tube 1

33. Rubber Hose 15∅x 1140mm (Oil Return 440mm, Blow By 300mm, Power Steering 200mm) 1

34. Silicone Hose 50∅x 70mm Straight 6

35. “ 80∅x80mmStraight 2

36. “ 60∅- 70∅Reducer 2

37. “ 60∅- 80∅Reducer 2

38. “ 70∅- 80∅Reducer 1

39. Hose Band 12∅#8 4

40. “ 16∅#10 9

41. “ 50∅#32 ____________ 12

42. “ 60∅#36 4

43. “ 70∅#44 5

44. “ 80∅#48 7

45. Power Steering Pump Fitting 1

46. Check Valve (Nissan factory part #47478-51E00) 1

47. Radiator Reserve Tank 1

48. Radiator Reserve tank Cap 1

49. Hose Fitting 8∅90°1

50. Radiator Reserve Tank Bracket A / B 1 Set

51. Aluminum Spacer t=28mm 1

52. Airinx Bracket Right / Left 1 Set

53. Hose Fitting 16∅Straight 1

54. Exhaust Manifold Gasket (Nissan Factory Part # 14036-AG010) 1 Set

55. Turbo Gasket TD05 In / Out 4

56. Catalytic Converter Gasket (Nissan Factory Part # 20813-AL500) 2

57. Oil Return Gasket TD Small 2

58. Thermo Cloth 100m x 1000mm 4

59. Three Way fitting 5∅- 6∅1

60. Zip Ties 150mm 15

61. E-Manage (US-Z33) 1

62.“Harrness 1

63.“I/JHarness 1

64. “ RPM signal adapter 1

65. Injectors 440cc (with 4 aluminum fuel rail spacers) 6

66. M5 x 15mm Stainless P=0.8 B S/W F/W N 1

67. M6 x 15mm Stainless P=1.0 B S/W - - 6

68. M6 x 15mm Stainless P=1.0 B S/W F/W N 5

69.M6x40mm Steel P=1.0 B - - - 1

70. M8 x 15mm Stainless P=1.25 B S/W - - 6

71. M8 x 20mm Stainless P=1.25 B S/W - - 2

72. M8 x 25mm Stainless P=1.25 B S/W - - 4

73. M8 x 30mm Stainless Stud P=1.25 – 1.25 B S/W - N 8

74. M10 x 35mm Stainless Stud P=1.25 – 1.25 B S/W - N____ 12

75. M10 x 45mm Stainless Stud P=1.25 – 1.50 B - - - 2

1. Parts List

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15 16

17 18 19 20

1. Parts List

21 22 23 24

25 26 27 28

29 30 - 33 34 - 38 39 - 40

45 46 47 48

49 50 51 52

1. Parts List

53 54 55 56

57 58 59 60

61 62 63 64

65 66 - 75

2. Factory Parts Removal

When removing the stock parts, make sure you read over the

factory repair manual for proper procedures.

2-1 Disconnect the negative terminal of the battery.

2-2 Drain the engine oil, coolant and power steering fluid.

2-3 Disconnect the air flow meter.

2-4 Remove the Air cleaner assembly with airflow meter, intake tube, and breather

hose.

2-5 Remove the Top Radiator Hose and the Water Pipe (Located above the Right

Exhaust manifold).

2-5 Disconnect the primary and secondary O2 sensor and remove the exhaust

manifold and catalytic converter.

2-6 Remove the exhaust manifold.

2-7 Remove oil pan (Please refer to the factory service manual for detail instructions f

or removing the oil pan.)

2-8 Remove the upper intake manifold collector, fuel rail assembly with injectors and

regulator.

3. Turbo Kit Installation

Thermo Cloth Installation

•Remove the bracket securing the fuel line right below the right side shock tower and

disconnect the fuel line. Flip the connector so that the line points up and reconnect the

line. Double wrap the fuel and evap Line using safety Wire. Leave the top bracket off

and secure the bottom back on as shown.

(Parts used #58)

(This picture shows the turbo already installed)

Important!

•Make sure that the fuel line is secured away from the turbine housing when the

turbo is installed. Some bending of the lines is necessary to achieve good

clearance.

•Make sure the lines are properly wrapped twice.

•Make sure to use safety wire to wrap the thermo cloth. Zip ties will melt from the

heat and eventually will come off.

•Make sure that the fuel line connector is properly clicked in all the way.

•GReddy Performance Products, Inc. will not be responsible for any damage

caused due to improper installation.

Caution!

•Make sure to check and double check this step. This is the most important

step in this install.

•Without proper clearance and thermo wrapping the fuel lines, the fuel line

connector can melt from heat and may catch on fire.

•Wrap the Starter and the Main Engine

harness right above the transmission bell

housing.

Important!

Make sure that the main engine harness is

properly wrapped and secured away from the

manifold and the wastegate when they are

installed.

Caution!

Without proper clearance and thermo wrapping the harness, it melt and cause a short

in the electrical system or may catch on fire.

Power Steering Line Installation

1. Remove the hose fitting off the power

steering pump and install the provided

fitting.

(Parts Used #40, 45)

2. Cut the provided 15∅hose to 200mm (8in)

and install it between the pump and the

tank.

(Parts Used #33)

Oil Pan Installation

Install the Oil pan with a silicone sealant.

(Part Used #29)

Andere Handbücher für Turbo Kit

Inhaltsverzeichnis

Andere GReddy Autozubehör Handbücher

GReddy

GReddy SW-20 Bedienungsanleitung

GReddy

GReddy 12559101 Bedienungsanleitung

GReddy

GReddy Profec Bedienungsanleitung

GReddy

GReddy Turbo Kit Bedienungsanleitung

GReddy

GReddy 12569001 Bedienungsanleitung

GReddy

GReddy Intercooler Kit Bedienungsanleitung

GReddy

GReddy Turbo Kit Bedienungsanleitung

GReddy

GReddy e-manage ultimate Bedienungsanleitung

GReddy

GReddy Turbo Kit Bedienungsanleitung

GReddy

GReddy Turbo Kit Emanage Ultimate Bedienungsanleitung

GReddy

GReddy Full Auto Timer Bedienungsanleitung

GReddy

GReddy 12539003 Bedienungsanleitung

GReddy

GReddy Intercooler Kit Bedienungsanleitung

GReddy

GReddy Type-RS BRS-HGC20 Bedienungsanleitung

GReddy

GReddy Turbo Kit Bedienungsanleitung

GReddy

GReddy Turbo Kit Bedienungsanleitung

GReddy

GReddy Turbo Kit Bedienungsanleitung

GReddy

GReddy AERO KIT Bedienungsanleitung

GReddy

GReddy BRS-503 Bedienungsanleitung

GReddy

GReddy TYPE-RS BRS-313 CT9A Bedienungsanleitung

GReddy

GReddy TYPE-RS BRS-307 D32 Bedienungsanleitung

GReddy

GReddy TYPE-RS BRS-112 JZA80 Bedienungsanleitung

GReddy

GReddy 12529003 Bedienungsanleitung

GReddy

GReddy 12529001 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung