Greenlee CMF-110 Bedienungsanleitung

Read and understand all of the instructions and safety information in

this manual before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre

seguridad que aparecen en este manual, antes de manejar estas

herramientas o darles mantenimiento.

Lire attentivement et bien comprendre toutes les instructions et

les informations sur la sécurité de ce manuel avant d’utiliser ou de

procéder à l’entretien de cet outil.

Flex Clamp Meters

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Español.............14

Français ...........27

CMF-110

CMF-118

Table of Contents

Description ....................................................................................................2

Safety............................................................................................................2

Important Safety Information......................................................................3–5

Identication..................................................................................................6

Display Icons .................................................................................................7

Operation.................................................................................................8–10

Typical Measurements and Accuracy .....................................................11–12

Specications..............................................................................................12

Measurement Categories.............................................................................13

Statement of Conformity..............................................................................13

Maintenance................................................................................................13

Description

The Greenlee CMF-110 and CMF-118 Flex Clamp Meters are hand-held testing devices

that measure AC current, AC voltage, resistance, and frequency. These meters are

designed to be placed on or removed from insulated or uninsulated conductors.

Safety

Safety is essential in the use and maintenance of Greenlee tools. This instruction

manual and any markings on the tool provide information for avoiding hazards

and unsafe practices related to the use of this tool. Observe all of the safety

information provided.

CMF-110 • CMF-118

SAFETY ALERT SYMBOL

This symbol is used to call your attention to hazards or unsafe practices which

could result in an injury or property damage. The signal word, dened below,

indicates the severity of the hazard. The message after the signal word provides

information for preventing or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

Read and understand this material before operating or servicing

this equipment. Failure to understand how to safely operate this

tool could result in an accident causing serious injury or death.

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

Important Safety Information

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

All specications are nominal and may change as design improvements occur. Greenlee Tools, Inc.

shall not be liable for damages resulting from misapplication or misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark

of Greenlee Tools, Inc.

KEEP THIS MANUAL

Important Safety Information (cont.)

Electric shock and re hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Clamp meter, test leads or any other clamp accessory, when used to make a

measurement, create a System. The System is rated for CAT IV 600V when using

the test leads or accessories provided with the meter. The System CAT and voltage

rating is limited by the lowest rated component in the System when using test leads

or accessories not provided with the meter.

• Inspect the test leads or accessory before use. They must be clean and dry, and

the insulation must be in good condition. Do not use the test lead if the contrasting

inner layer of insulation is visible.

• Use this unit for the manufacturer’s intended purpose only, as described in this

manual. Anyotheruse can impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or

between any input terminal and earth ground.

• Keep hands and ngers below the barriers on the test leads and the clamp

meter body.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not operate with the case open.

• Before opening the case, remove the test leads from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

CMF-110 • CMF-118

Important Safety Information (cont.)

Electric shock hazard:

• Unless measuring voltage, current, or frequency, shut off and lock out power. Make

sure that all capacitors are discharged. Voltage must not be present.

• Set the selector and connect the test leads so that they correspond to the intended

measurement. Incorrect settings or connections can result in incorrect measure-

ments or damage to the unit.

• Using this unit near equipment that generates electromagnetic interference can

result in unstable or inaccurate readings.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not change the measurement function while the test leads are connected to a

component or circuit.

Failure to observe these precautions may result in injury and can damage the unit.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity. Refer

to “Specications.”

Failure to observe these precautions may result in injury and can damage the unit.

Identication

1. Rogowski Coil - The measurement coil of ex clamp meter

2. Clamp Lock - Turn the knob counter-clockwise to unlock the clamp; turn

clockwise to lock the clamp.

3. LCD - Displays measurement data and function modes

4. "HOLD "/ - Press to turn ON/OFF hold mode. Press and hold to turn

the unit ON/OFF.

5. " " and " INRUSH " - Press to turn ON/OFF backlight. Press and hold for 2

seconds to turn ON/OFF inrush measurement mode

6."RANGE" and "Hz" - Press to switch between 30.00A/300.0A/3000A/Auto;

The Default is Auto

7. Power and Range Shift Switch: Set to A for current measurement, V for AC voltage

measurement, and Ω for resistance measurement.

8. Voltage and Resistance Measurement Input:

Maximum AC voltage measurement is 600V, maximum resistance is 60MΩ

Symbols on the Unit

Double Insulation Low Battery

Grounding AC/DC

Warning High Voltage Danger

AC Complies with European

Union Standards

DC ETL Standard Certication

Figure 1

CMF-110 • CMF-118

Display Icons

Symbol Description Symbol Description

INRUSH 80 ms inrush measurement Unit A, Hz, V, Ω, kΩ, MΩ

Buzzer APO Auto Power Off

Low Battery Data hold

Double Insulation Low Battery

Grounding AC/DC

Warning High Voltage Danger

AC Complies with European

Union Standards

DC ETL Standard Certication

Figure 2

Operation

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

Keep your hands away from the Rogowski coil and conductor to be measured.

Disconnect all power supplies from the device before measurement. When measuring

uninsulated conductors, do not power on the wire to be tested until the meter has

safely clamped the wire.

1. Turn off the clamp as well as the conductor being measured.

2. Unlock the clamp according to Figure 3

3. Use the measuring head to wrap around the conductor to be measured and lock it

in place. (Only one wire can be tested at a time; See Figure 4)

4. Turn on the clamp and adjust the slider to measure current, then turn on

the conductor to be measured.

5. Read the value displayed on the LCD. If the current to be measured is over

the range, OL appears on the LCD. Please select the appropriate range.

(30.00A/300.0A/3000A)

6. Improper operation examples:

a. Do not test more than one conductor at a

time as shown in as shown in Figure 5

b. Do not attempt to twist, bend, or wrap the coil

of the CMF-110/118 as shown in Figures 6, 7, and 8.

c. Do not attempt to pull on or apply a force to the

coil of the CMF-110/118

Figure 5

Figure 3 Figure 4

CMF-110 • CMF-118

Operation (cont.)

Figure 6

Figure 8

Figure 7

Operation (cont.)

AC Voltage and Frequency Measurement

1. Insert the black test lead to the COM jack, and the red test

lead to the V jack.

2. Switch the functional switch to the V position

3. Press and hold RANGE to turn on frequency measurement mode,

otherwise skip to step 4.

4. Connect the test leads to the voltage to be tested (Figure 9)

and the meter will automatically select the range. The main

display will show the AC voltage RMS and the auxiliary display

will show the frequency value.

Do not input over AC 600V.

Resistance Measurement

1. Insert the black test lead to the COM jack and the red test lead

to the V jack

2. Switch the functional switch to the Ω position

3. Connect the test leads to the resistance to be tested (Figure 10)

and the meter will automatically select the range. The main display

will show the resistance value.

Before measuring, please disconnect the power supply and

fully discharge all capacitors. The result will be more accurate

if the resistor is separated from the whole circuit.

Auto Power Off

During measurement, if there is no operation within 10 minutes,

the meter will power off automatically to save energy. Press the

and RANGE buttons at the same time to turn ON/OFF the APO function.

The APO function is active by default.

Figure 9

Figure 10

Andere Handbücher für CMF-110

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Messgerät Handbücher

Greenlee

Greenlee SM-100 Bedienungsanleitung

Greenlee

Greenlee CMT-90 Bedienungsanleitung

Greenlee

Greenlee SML-200 Bedienungsanleitung

Greenlee

Greenlee 93-172 Bedienungsanleitung

Greenlee

Greenlee DataScout 10G Bedienungsanleitung

Greenlee

Greenlee 93-804 Leitfaden

Greenlee

Greenlee 920XC-13A Bedienungsanleitung

Greenlee

Greenlee CM-600 Bedienungsanleitung

Greenlee

Greenlee 5778 Leitfaden

Greenlee

Greenlee Pull Connect Bedienungsanleitung

Greenlee

Greenlee CM-1360 Bedienungsanleitung

Greenlee

Greenlee 93-172 Bedienungsanleitung

Greenlee

Greenlee CS-8000 Circuit Seeker Bedienungsanleitung

Greenlee

Greenlee IPM-300 Bedienungsanleitung

Greenlee

Greenlee CMT-80 Bedienungsanleitung

Greenlee

Greenlee AirScout Gigacheck Bedienungsanleitung

Greenlee

Greenlee 5990A Bedienungsanleitung

Greenlee

Greenlee 967 Bedienungsanleitung

Greenlee

Greenlee GOPM Micro-01 Bedienungsanleitung

Greenlee

Greenlee TML-30 Bedienungsanleitung

Greenlee

Greenlee CM-1360 Bedienungsanleitung

Greenlee

Greenlee HCO-100 Bedienungsanleitung

Greenlee

Greenlee BLL-200 Bedienungsanleitung

Greenlee

Greenlee AM-1000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung