Guardian Diablo 2.5 Cable SRL-LE Bedienungsanleitung

Product Name: Diablo 2.5 Cable SRL-LE

Instruction Manual

Part #: 11100CSA; 11101CSA; 11102CSA; 11103CSA; 11104CSA; 11105CSA; 11106CSA; 11107CSA

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Introduction 1

Applicable Safety Standards 1

Worker Classifications 1

Safety Information 9

Product Specific Applications 2

Limitations 2 - 3

Components and Specifications 3 - 4

Maintenance, Cleaning, and Storage 7

Inspection 8

Installation and Use 4 - 7

Inspection Log 8

Labels 10 - 11

Introduction

Thank you for purchasing a Guardian Fall

Protection Diablo 2.5 Cable SRL-LE. This

manual must be read and understood in its

entirety, and used as part of an employee

training program as required by OSHA or any

applicable state agency.

This and any other included instructions

must be made available to the user of the

equipment. The user must understand how

to safely and effectively use the Diablo Cable

SRL-LE, and all fall safety equipment used in

combination with the Diablo 2.5 Cable SRL-LE.

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926

Subpart M, OSHA 1910, ANSI Z359.14-2014, ANSI A10.32-2012, and CSA Z259.2.2-2017 standards for fall

protection. Applicable standards and regulations depend on the type of work being done, and also might

include state-specific regulations. Consult regulatory agencies for more information on fall protection systems

and associated components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall

protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,

and application. A person who is proficient in identifying existing and predictable fall hazards, and who has

the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all

applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Product Specific Applications

Restraint: Diablo 2.5 Cable SRL-LE may be used in Restraint applications. Restraint systems prevent

workers from reaching the leading edge of a fall hazard. Always account for fully deployed length

of lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system

of at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces

with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.

WARNING

Use of equipment in unintended applications may result in serious

injury or death. Maximum 1 attachment per connection point.

Limitations

Fall Clearance: There must be sufficient

clearance below the anchorage connector to

arrest a fall before the user strikes the ground

or an obstruction. When calculating fall

clearance, account for a MINIMUM 2’ safety

factor, deceleration distance, user height, length

of lanyard/SRL, harness stretch, and all other

applicable factors.

Diagram shown is an example fall

clearance calculation ONLY.

Swing Falls: Prior to installation or use, make

considerations for eliminating or minimizing

all swing fall hazards. Swing falls occur when

the anchor is not directly above the location

where a fall occurs. Always work as close to in

line with the anchor point as possible. Swing

falls significantly increase the likelihood of

serious injury or death in the event of a fall.

Diablo 2.5 Cable SRL-LE recommended fall clearance

(Does not factor in any potential swing fall hazards.

Clearance numbers specified based on lifeline

installed vertically overhead and in-line with worker.):

• LE Use: 13‘-17’

• Non-LE Use: 5½’ (no free fall) to 7½’ (maximum 2’ free fall)

Personal Fall Arrest: Diablo 2.5 Cable SRL-LEs may be used in Personal Fall Arrest applications as

a component of a MAXIMUM 1 Personal Fall Arrest System (PFAS). Structure must withstand loads

applied in the directions permitted by the system of at least 5,000 lbs. Applicable D-ring: Dorsal.

• Free fall, non-LE Use: Maximum 2’.

• Free fall, LE Use: Maximum 5’. Please note that free fall in excess of 2’ is not in compliance with

ANSI A10.32-12 fall protection regulations, but is still fully compliant with all applicable ANSI

Z359.14-14, OSHA 1926 Subpart M, and OSHA 1910 regulations.

For all applications, worker weight capacity range (including all clothing, tools, and equipment):

LE Use: 130-310 lbs.

Non-LE Use: 130-420 lbs.

*Eliminate Swing Fall whenever

possible! If Swing Fall exists,

always account for additional

fall clearance.

Anchor Point

at Foot Level

Class B SRL

SRL-LE

4.5’

8.5’

5’

2’

1.5’

Work Surface

4.5’

2’

1.5’

2’

max.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Components and Specifications

Compatibility: When making connections with Diablo 2.5 Cable SRL-LE, eliminate all possibility of roll-out.

Roll-out occurs when interference between a hook and the attachment point causes the hook gate to

unintentionally open and release. All connections must be selected and deemed compatible with Diablo 2.5

Cable SRL-LE by a Competent Person. All connector gates must be self-closing and self-locking, and withstand

minimum loads of 3,600 lbs. See the following for examples of compatible/incompatible connections:

Connector

closed and

locked to

D-ring. OK.

Two or more

snap hooks or

carabiners

connected to

each other. NO.

Two connectors

to same

D-ring. NO.

Connector

directly to

horizontal

lifeline. NO.

Connector

to integral

lanyard.

NO.

Connector

directly to

webbing.

NO.

Incompatible

or irregular

application,

which may

increase risk

of roll-out. NO.

Materials: aluminum, galvanized steel, stainless steel, zinc-plated steel, high-strength ABS, and polyester.

Non-LE Use:

Max. arresting distance: 54”

Min. fall clearance: 9’

Class B SRL

LE Use:

Min. setback distance from edge: 0’

Max. arresting distance: 54” - 102”

Min. fall clearance: 13’-17’

Average arresting force: 900 lbs.

Cable

Lifeline

Housing

Rubber

Stopper

SRL Bracket

Hook

Shock Absorber /

Back Pad

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Part # Length Description

11100CSA

11101CSA

11102CSA 8’

8’

3/16” Galvanized Cable SRL-LE w/Carabiner, Swivel Top, Shock Pack, & Steel Snap Hook

3/16” Galvanized Cable SRL-LE w/Carabiner, Swivel Top, Shock Pack, & Aluminum Snap Hook

3/16” Galvanized Cable SRL-LE w/Carabiner, Swivel Top, Shock Pack, & Steel Rebar Hook

11103CSA 8’ 3/16” Galvanized Cable SRL-LE w/Carabiner, Swivel Top, Shock Pack, & Aluminum Rebar Hook

11104CSA

11105CSA

11106CSA

11107CSA

8’

Kit of (2) 11100 Galvanized Cable SRL-LEs w/Steel Snap Hooks. Includes (1) SRL Connector Bracket & (1) Carabiner.

Kit of (2) 11101 Galvanized Cable SRL-LEs w/Aluminum Snap Hooks. Includes (1) SRL Connector Bracket & (1) Carabiner.

Kit of (2) 11102 Galvanized Cable SRL-LEs w/Steel Rebar Hooks*. Includes (1) SRL Connector Bracket & (1) Carabiner.

Kit of (2) 11103 Galvanized Cable SRL-LEs w/Aluminum Rebar Hooks. Includes (1) SRL Connector Bracket & (1) Carabiner.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Installation and Use

1. All PFAS components must be selected and deemed compatible with Diablo 2.5 Cable SRL-LE by Competent

Person.

2. Ensure structure to which Diablo 2.5 Cable SRL-LE is to be attached, and on which work is to be performed,

is free of all hazards, including, but not limited to, debris, rot, rust, sharp or abrasive edges and surfaces, and

hazardous materials.

3. Eliminate or minimize all risk of swing fall hazard.

4. Ensure 100% tie-off will be maintained at all times, which may require the use of a back-up or

supplementary fall protection system.

5. Always minimize lifeline contact with sharp or abrasive edges and surfaces.

To install Diablo 2.5 Cable SRL-LE to harness:

1. Compress and hold both release buttons on SRL Bracket and slide pin to open position. Do not attempt to

open or otherwise modify bracket that is connected to Diablo 2.5 Cable SRL-LE.

Release

buttons

2. At web loop immediately beneath harness dorsal D-ring, slide SRL Bracket pin through loop and lock closed.

It may be necessary to slightly loosen web loop to accommodate pin. Always re-tighten web loop after install.

Depending on SRL Bracket design, either ensure green indicator IS fully visible, or that red indicator

IS NOT visible.

Note: With Diablo 2.5 Cable SRL-LE attached to harness as shown, it is permitted to connect a separate

connecting device to the harness dorsal D-ring. However, never work with more than one connecting device

attached to an anchorage connector at any time.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

SRL Bracket installed at web loop.

Green indicator visible -

OK to use.

Red indicator visible -

DO NOT use.

Additional installation/use notes:

1. It is not possible to transform a single unit Diablo 2.5 Cable SRL-LE into a double unit, nor possible to

transform a double unit into a single unit. Never attempt to modify equipment at any time.

2. When Diablo 2.5 Cable SRL-LE is not in use, always secure hook to harness lanyard keeper. For double units,

always keep unused leg of SRL secured to harness lanyard keeper except when transitioning between anchor

points.

Diablo SRL-LE back pad hook and loop fastener straps

secured around harness shoulder straps.

3. Secure Diablo SRL-LE back pad around harness shoulder straps with provided hook and loop fastener straps

as shown.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Maintenance, Cleaning, and Storage

If Diablo 2.5 Cable SRL-LE fails inspection in any way, immediately remove it from service and contact

Guardian.

Cleaning after use is important for maintaining the safety and longevity of Diablo 2.5 Cable SRL-LE. Remove all

dirt, corrosives, and contaminants from Diablo 2.5 Cable SRL-LE before and after each use. If Diablo 2.5 Cable

SRL-LE cannot be cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean

Diablo 2.5 Cable SRL-LE with corrosive substances.

When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,

or other degrading elements.

SRL-LE Additional Use Instructions:

ALWAYS adhere to the following warnings and specifications when using SRL-LEs.

WARNING

Setback Distance

Image 1 Image 2

Leading Edge

X≤90°

X≥90°

Diablo 2.5 Cable SRL-LEs are tested and certified for horizontal use over a steel edge without burrs. Diablo

Cable SRL-LEs may be used over similar surfaces, such as metal sheeting or other steel formations.

The allowable angle of redirection of the lifeline portion of Diablo 2.5 Cable SRL-LEs at the leading edge of a

fall hazard MUST be at least 90° (see Image 1).

Anchor point MUST be situated no lower than the leading edge of applicable fall hazard(s).

Prior to use, a Competent Person MUST calculate adequate fall clearance (see pg. 3).

ALWAYS attach to anchorage connector that will allow for required setback distance (see Image 2).

Setback distance: As determined by product testing, Guardian Fall Protection Diablo 2.5 Cable SRL-LEs

are not required to be setback any specific distance from the leading edge of applicable fall hazard(s).

Diablo 2.5 Cable SRL-LE may be used in combination with horizontal lifelines. All installation, set-up, and use

of horizontal lifelines must be done under the supervision of a Qualified Person.

NEVER work on the far side of an opening that is opposite the Diablo 2.5 Cable SRL-LE anchorage point.

In the event of a fall over the edge, special rescue measures may be necessary. Always account for use of

Diablo Cable SRL in job site rescue plan developed by job site Competent Person.

Prior to EACH use, inspect Diablo 2.5 Cable SRL-LE for deficiencies, including, but not limited to, corrosion,

deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating,

alteration, broken stitching, fraying, bird-caging, and missing or illegible labels.

Pay careful attention to cable swage (located beneath rubber stopper) and ensure no damage is present at

location where swage contacts lifeline. IMMEDIATELY remove Diablo 2.5 Cable SRL-LE from service if defects or

damage are found, or if exposed to forces of fall arrest. Ensure fall arrest indicator (broken stitching at location

shown below) is not deployed. During inspection, consider all applications and hazards Diablo 2.5 Cable SRL-LE

has been subjected to.

Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,

cracking, and hazardous materials. Ensure that selected work area will support the application-specific

minimum loads set forth in this instruction manual. Work area MUST be stable.

At least every 12 months, a Competent Person other than the user must inspect Diablo 2.5 Cable SRL-LE.

Competent Person inspections MUST be recorded in inspection log in instruction manual and on

equipment inspection grid label. The Competent Person must sign their initials in the box

corresponding to the month and year the inspection took place.

Immediately remove from service if indicator stitching shows any signs of damage:

Inspection

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Intact indicator stitching - OK to use.

Broken/damaged indicator stitching - Immediately remove from service!

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Inspection Log

Date of First Use: __________________.

Product lifetime is indefinite, as long as it passes pre-use and Competent Person inspections. User must

inspect prior to EACH use. Competent Person other than user must complete formal inspection at least

every 12 months. Competent Person to inspect and initial.

This inspection log must be specific to one Diablo 2.5 Cable SRL-LE. Separate inspection logs must be

used for each Diablo 2.5 Cable SRL-LE. All inspection records must be made visible and available to all

users at all times.

If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Guardian Sicherheitsausrüstung Handbücher

Guardian

Guardian FABX Bedienungsanleitung

Guardian

Guardian CR3 SELF-RETRACTING LIFELINE Bedienungsanleitung

Guardian

Guardian 10736 Bedienungsanleitung

Guardian

Guardian ProTec Einrichtungshandbuch

Guardian

Guardian MDS89745RA Bedienungsanleitung

Guardian

Guardian HALO BIG BLOCK SRL-LE Bedienungsanleitung

Guardian

Guardian WEB HORIZONTAL LIFELINE Bedienungsanleitung

Guardian

Guardian B7-COMFORT Bedienungsanleitung

Guardian

Guardian CR5 Bedienungsanleitung

Guardian

Guardian 42102 Bedienungsanleitung

Guardian

Guardian 15220 Bedienungsanleitung

Guardian

Guardian CABLE CLIMBING SYSTEM Bedienungsanleitung

Guardian

Guardian HALO Bedienungsanleitung

Guardian

Guardian Diablo SRL-LE Bedienungsanleitung

Guardian

Guardian 10785 Bedienungsanleitung

Guardian

Guardian FABXR Bedienungsanleitung

Guardian

Guardian XPLORER Bedienungsanleitung

Guardian

Guardian 42107 Bedienungsanleitung

Guardian

Guardian EXPOSURE OLAS Bedienungsanleitung

Guardian

Guardian Diablo 2.0 SRL Bedienungsanleitung

Guardian

Guardian G2-200KHX1 Bedienungsanleitung

Guardian

Guardian 00500 Bedienungsanleitung

Guardian

Guardian 10920 Bedienungsanleitung

Guardian

Guardian 42115 Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung