Guardian Halo SRL Series Bedienungsanleitung

Introduction 1

Applicable Safety Standards 1

Worker Classifications 1

Safety Information 6

Product Specific Applications 2

Limitations 2 - 3

Components and Specifications 3

Maintenance, Cleaning, and Storage 4

Inspection 5

Installation and Use 4

Inspection Log 5

Labels 7

Product Name: Halo Series SRL

Instruction Manual

Part #: 10910CSA; 10912CSA; 10915CSA

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Introduction

Thank you for purchasing a Guardian Fall Protection Halo Series SRL. This manual must be read and understood

in its entirety, and used as part of an employee training program as required by OSHA or any applicable state

agency.

This and any other included instructions must be made available to the user of the equipment. The user must

understand how to safely and effectively use the Halo Series SRL, and all fall safety equipment used in

combination with the Halo Series SRL.

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926

Subpart M, OSHA 1910, ANSI Z359.14-2014, and ANSI A10.32-2012 standards for fall protection. Applicable

standards and regulations depend on the type of work being done, and also might include state-specific

regulations. Consult regulatory agencies for more information on personal fall arrest systems and associated

components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall

protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,

and application. A person who is proficient in identifying existing and predictable fall hazards, and who has

the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all

applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Product Specific Applications

Restraint: Halo Series SRLs may be used in Restraint applications. Restraint systems prevent

workers from reaching the leading edge of a fall hazard. Always account for fully deployed length

of lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system

of at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces

with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.

WARNING

Use of equipment in unintended applications may result in serious

injury or death. Maximum 1 attachment per connection point.

Personal Fall Arrest: Halo Series SRLs may be used in Personal Fall Arrest applications as a

component of a MAXIMUM 1 Personal Fall Arrest System (PFAS). Structure must withstand loads

applied in the directions permitted by the system of at least 5,000 lbs. No free fall is permitted.

SRL must always be positioned at or above harness dorsal D-ring AND at or below anchor point.

Applicable D-ring: Dorsal.

Limitations

Fall Clearance: There must be

sufficient clearance below the

anchorage connector to arrest

a fall before the user strikes

the ground or an obstruction.

When calculating fall clearance,

account for a MINIMUM 2’

safety factor, deceleration

distance, user height, length

of lanyard/SRL, harness stretch,

and all other applicable factors.

Diagram shown is an example

fall clearance calculation ONLY.

Swing Falls: Prior to installation

or use, make considerations for

eliminating or minimizing all

swing fall hazards. Swing falls

occur when the anchor is not

directly above the location

where a fall occurs. Always

work as close to in line with

the anchor point as possible.

Swing falls significantly increase

the likelihood of serious injury

or death in the event of a fall.

Fall clearance calculation shown

based on standing worker falling

directly in-line with anchor point.

Always consider potential swing

fall and other hazards when

calculating fall clearance.

2’

Permitted weight capacity varies based on regulation. For all applications, worker weight capacity

range (including all clothing, tools, and equipment) is as follows:

• OSHA: 100-310 lbs. • CSA: 100-310 lbs.• ANSI: 130-310 lbs.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Components and Specifications

Made from aluminum, galvanized steel, stainless steel, and zinc-plated steel components.

Part # Length Description

10910CSA

10912CSA

10915CSA

20’

25’

30’

3/16” Galvanized Cable w/Carabiner, Swivel Top, & Snap Hook

Connector

Housing

Lifeline

Carabiner

Connection

Point

Compatibility: When making connections with Halo Series SRL, eliminate all possibility of roll-out. Roll-out

occurs when interference between a hook and the attachment point causes the hook gate to unintentionally

open and release. All connections must be selected and deemed compatible with Halo Series SRL by a

Competent Person. All connector gates must be self-closing and self-locking, and withstand minimum loads of

3,600 lbs. See the following for examples of compatible/incompatible connections:

Max. arresting distance: 54”

Min. fall clearance: 9’

Class B SRL

Connector

closed and

locked to

D-ring. OK.

Connector

to integral

lanyard.

NO.

Two or more

snap hooks or

carabiners

connected to

each other. NO.

Two connectors

to same

D-ring. NO.

Connector

directly to

horizontal

lifeline. NO.

Connector

directly to

webbing.

NO.

Incompatible

or irregular

application,

which may

increase risk

of roll-out. NO.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Maintenance, Cleaning, and Storage

Repairs to Halo Series SRL can only be made by a Guardian Fall Protection representative or an entity

authorized by Guardian. Contact Guardian for all maintenance and repair needs at: 1-800-466-6385. If Halo

Series SRL fails inspection in any way, immediately remove it from service, and contact Guardian to inquire

about its return or repair.

Cleaning after use is important for maintaining the safety and longevity of Halo Series SRL. Remove all dirt,

corrosives, and contaminants from Halo Series SRL before and after each use. If Halo Series SRL cannot be

cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean Halo Series SRL

with corrosive substances.

When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,

or other degrading elements.

Installation and Use

Guardian Fall Protection Halo Series SRLs MUST NEVER be used in Leading Edge (LE) applications.

No free fall is allowed.

ALWAYS avoid lifeline contact with sharp or abrasive edges and surfaces.

1. All components of the personal fall arrest system must be selected and deemed compatible with applicable

SRL by a Competent Person.

2. Ensure structure to which SRL is to be attached, and on which work is to be performed, is free of all hazards,

including, but not limited to, debris, rot, rust, sharp or abrasive edges and surfaces, and hazardous materials.

3. Halo Series SRL may be used in either mobile or stationary applications.

4. For stationary applications, attach Halo Series SRL carabiner to selected anchorage connector, and attach

snap hook to applicable harness D-ring.

5. For mobile applications, attach SRL carabiner to harness Dorsal D-ring, and attach snap hook to selected

anchorage connector.

6. Ensure 100% tie-off will be maintained at all times, which may require the use of a back-up or

supplementary fall protection system.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Inspection

Prior to EACH use, inspect Halo Series SRL for deficiencies, including, but not limited to, corrosion, deformation,

pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, broken

stitching, fraying, bird-caging, and missing or illegible labels. Inspect full length of lifeline. Pay careful

attention to cable swage (located beneath rubber stopper) and ensure no damage is present at location where

swage contacts lifeline. IMMEDIATELY remove Halo Series SRL from service if defects or damage are found.

Prior to EACH use, check lifeline retraction

by pulling out a minimum 4’ and allowing

it to retract under light tension; lifeline

must retract completely. Pull lifeline

sharply to test braking function; brakes

must engage. Depending on model or

configuration, check shock pack for signs

of deployment, and/or fall arrest indicator

for signs of activation. Indicator will

display red if unsafe for use. See images

on right. Deployed indicator will also

allow swivel eye to lift up and away

from main body of hook as shown.

IMMEDIATELY remove from service if

Halo Series SRL does not function properly,

or if exposed to forces of fall arrest.

Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,

cracking, and hazardous materials. Ensure that selected work area will support the application-specific

minimum loads set forth in this instruction manual. Work area MUST be stable.

Every 12 months, a Competent Person other than the user must inspect Halo Series SRL. Competent Person

inspections MUST be recorded in inspection log in instruction manual and on equipment inspection grid

label. The Competent Person must sign their initials in the box corresponding to the month and year

the inspection took place.

During inspection, consider all applications and hazards SRLs have been subjected to.

Not Deployed

(OK for use) Deployed

(REMOVE FROM SERVICE)

Inspection Log

If equipment fails inspection

IMMEDIATELY REMOVE FROM SERVICE.

Date of First Use: __________________.

Product lifetime is indefinite, as long as product

passes all inspection requirements. User must

inspect prior to EACH use. Competent Person other

than user must complete formal inspection at

least every 12 months. Competent Person to

inspect and initial.

This inspection log must be specific to one Halo

Series SRL. Separate inspection logs must be used

for each Halo Series SRL. All inspection records

must be made visible and available to all users

at all times.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Safety Information

Failure to understand and comply with safety regulations may result in

serious injury or death. Regulations included herein are not all-inclusive,

are for reference only, and are not intended to replace a Competent

Person’s judgment or knowledge of federal or state standards.

WARNING

Do not alter equipment. Do not misuse equipment.

Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects,

machinery, abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent

Person before fall protection equipment is selected.

The analysis of the workplace must anticipate where workers will be performing their duties, the routes they

will take to reach their work, and the potential and existing fall hazards they may be exposed to. Fall

protection equipment must be chosen by a Competent Person. Selections must account for all potential

hazardous workplace conditions. All fall protection equipment should be purchased new and in an unused

condition.

Fall protection systems must be selected and installed under the supervision of a Competent Person, and used

in a compliant manner. Fall protection systems must be designed in a manner compliant with all federal, state,

and safety regulations. Forces applied to anchors must be calculated by a Competent Person.

Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must not exceed 6’.

Class B SRLs must arrest falls within 54”.

Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be of

compatible size and configuration. Snap hooks, carabiners, and other connectors must be selected and applied

in a compatible fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be

self-locking and self-closing, and must never be connected to each other.

A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-specific. The

rescue plan must allow for employees to rescue themselves, or provide an alternative means for their prompt

rescue. Store rescue equipment in an easily accessible and clearly marked area.

Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment

must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize

the likelihood of fall hazards, and the correct use of personal fall arrest systems.

NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless

explicitly certified for such use.

Equipment subjected to forces of fall arrest must immediately be removed from use.

Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there

is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of

equipment. Pregnant women and minors must not use this equipment.

Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension

may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Labels

85396 (Rev. A)

WARNING: Follow all

manufacturer’s

instructions included

at time of shipping.

AVERTISSEMENT :

Suivre toutes les

instructions du

fabricant fournies

avec le produit lors

de sa livraison.

WARNING: Lifeline

shall not contact

edges or surfaces

during fall arrest.

AVERTISSEMENT : La

ligne de vie ne doit pas

entrer en contact avec

des bord coupant ou

des surfaces lors

d'une chute.

WARNING: Anchor

above user’s Dorsal

D-Ring.

AVERTISSEMENT :

Ancrer au-dessus de

l’anneau en D dorsal

du harnais de

l’utilisateur.

WARNING: This device

shall be removed from

service when the

visual load indicator

is deployed.

AVERTISSEMENT : Ce

produit doit être retiré

du service lorsque

l’indicateur de chute

est activé.

CSA Compliance Information

Lifeline: 30’ Câble, 3/16” width. /

Corde de seécurité: Sangles 30’ (9.1m),

largeur 3/16” (4.8mm).

Class SRL / Classe SRL.

Worker mass range: 100-310 lbs. /

Gamme de masse des travailleurs:

100-310 lbs. (45-140 kg).

For use by 1 worker only. /

Àutiliser par un seul travailleur.

Maximum arrest force: 1,800 lbs. /

Force d’arrestation maximale: 1,800 lbs. (8kN).

Maximum deployment: 54”. /

Déployment maximum: 54” (1.37m).

Maximum free fall: 0’. /

Chute libre maximale: 0’ (0m).

Favg: 900 lbs. (4kN)

D140.

91172 (Rev. A)

Serial #

10915CSA

30’ 3/16” CABLE

Lot # Mfg. Date

Part #

Date of First Use

WARNING: Prior to use, fully read and

understand all manufacturer’s instructions

provided with equipment at time of shipment.

DO NOT ATTEMPT TO SELF SERVICE OR REPAIR!

DO NOT REMOVE THIS LABEL.

USE: This device is only for use by one person as a fall

arrester. Only make connections directly to attachment

point on safety harness. Ensure that connection to

anchorage is secured properly before use. Avoid

lifeline contact with sharp or abrasive edges and

surfaces, and thermal, electrical, and chemical

hazards. May be used as a component of a

PFAS in HLL applications. Design,

installation, and utilization of HLLs must be

supervised by a Qualified Person.

Unsuitable for horizontal use. Competent

Person must calculate fall clearance prior to

use; fall clearance calculations must include

considerations for swing fall. Clearance number

specified is based on lifeline installed vertically

overhead and in-line with worker.

INSPECTION: Prior to each use, inspect

device per instructions, including locking

function (sharp pull to test), retraction function,

legibility of labels, evidence of defects, damage,

or missing parts, and condition of connectors,

housing, fasteners, and lifeline (inspect full length).

Inspection by Competent Person required at least

every 12 months. Immediately remove from service if

impact indicator on hook displays red.

SPECIFICATIONS:

Capacity range (per regulation):

- OSHA & ANSI: 100 - 310 lbs.

- ANSI: 130-310 lbs.

Average arresting force: 900 lbs.

Max. arresting distance: 54”

Min. Fall clearance: 9’

Class B SRL

Assembled in USA

91164 (Rev. A)

J F M AA JM J S O N D

ANSI Z359.14-14 & ANSI A10.32-12

OSHA 1910 & OSHA 1926 Subpart M

CSA Z259.2.2-17

Introducción 8

Estándares de seguridad aplicables 8

Clasificación de los trabajadores 8

Información de seguridad 13

Aplicaciones específicas del producto 9

Limitaciones 9 - 10

Componentes y especificaciones 10

Mantenimiento, limpieza y almacenamiento 11

Inspección 12

Instalación y uso 11

Registro de inspección 12

Etiquetas 14

Nombre del producto: Cuerda SRL de la serie Halo

Manual de instrucciones

Pieza #: 10910CSA; 10912CSA; 10915CSA

No se deshaga de estas instrucciones.

Lea y entienda estas instrucciones antes de usar el equipo.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 Teléfono: (800) 466-6385 Fax: (800) 670-7892 www.guardianfall.com

Introducción

Gracias por comprar una cuerda de salvamento autorretráctil SRL (self-retracting lifeline) de la serie Halo de

Guardian Fall Protection. Este manual se debe leer y entender en su totalidad, y usar como parte del programa de

capacitación del empleado según lo exige OSHA o cualquier dependencia estatal que corresponda.

Estas y otras instrucciones incluidas deben estar a disposición del usuario del equipo. El usuario debe entender

cómo usar de manera segura y funcional la cuerda SRL de la serie Halo, así como todo el equipo de seguridad

contra caídas que se usa en combinación con esta.

Información del usuario

Fecha del primer

# de serie:

Instructor:

Usu-

Estándares de seguridad aplicables

Cuando se usa conforme a las especificaciones de las instrucciones, este producto cumple o supera todos los

estándares OSHA 1926 Subparte M, OSHA 1910, ANSI Z359.14-2014 y ANSI A10.32-2012 aplicables a la

protección contra caídas. Los estándares y reglamentos aplicables dependen del tipo de trabajo que se esté

ejecutando, y podrían incluir también reglamentos estatales específicos. Consulte con los organismos

reguladores para obtener más información sobre los sistemas personales de detención de caídas y los

componentes asociados.

Clasificación de los trabajadores

CUIDADO

Conozca las siguientes definiciones de quienes trabajan

cerca o pueden estar expuestos a peligros de caída.

Persona calificada: Persona con una certificación acreditada o un título acreditado, y con amplia experiencia o

reputación profesional suficiente, que sea considerada competente en la planificación y revisión de la

conformidad de los sistemas de rescate y protección contra caídas.

Persona competente: Persona con gran capacidad y experiencia que EL EMPLEADOR ASIGNA como

responsable de todos los elementos de un programa de seguridad contra caídas, entre otros, su reglamento,

administración y aplicación. Es una persona experta en identificar los peligros de caída existentes y previsibles,

y con autoridad para suspender el trabajo con objeto de eliminar los peligros.

Persona autorizada: Persona asignada por el empleador para llevar a cabo trabajos o estar presente en

lugares de peligro potencial o existente de caída.

La responsabilidad de una persona calificada o de una persona competente es supervisar el sitio

de trabajo y comprobar que se cumpla con todos los reglamentos de seguridad aplicables.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Guardian Sicherheitsausrüstung Handbücher

Guardian

Guardian B7-COMFORT Bedienungsanleitung

Guardian

Guardian EyeSafe G1100 Montage- und Bedienungsanleitung

Guardian

Guardian 42100 Bedienungsanleitung

Guardian

Guardian FABX Bedienungsanleitung

Guardian

Guardian 10785 Bedienungsanleitung

Guardian

Guardian 10736 Bedienungsanleitung

Guardian

Guardian FABXR Bedienungsanleitung

Guardian

Guardian 15176 Bedienungsanleitung

Guardian

Guardian 42103 Bedienungsanleitung

Guardian

Guardian Diablo 42009CSA Bedienungsanleitung

Guardian

Guardian VERTICAL LIFELINE Bedienungsanleitung

Guardian

Guardian 00240 Bedienungsanleitung

Guardian

Guardian 42120 Bedienungsanleitung

Guardian

Guardian 00260 Bedienungsanleitung

Guardian

Guardian 00230 Bedienungsanleitung

Guardian

Guardian 01608 Bedienungsanleitung

Guardian

Guardian G2-200KHX1 Bedienungsanleitung

Guardian

Guardian DIABLO 10967 Bedienungsanleitung

Guardian

Guardian 36030 Bedienungsanleitung

Guardian

Guardian 42113 Bedienungsanleitung

Guardian

Guardian 01205 Bedienungsanleitung

Guardian

Guardian 10920 Bedienungsanleitung

Guardian

Guardian Diablo 2.5 Cable SRL-LE Bedienungsanleitung

Guardian

Guardian QSBOLT Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung