Heath Zenith 6168 Bedienungsanleitung

Wireless Door

Sensor Chime

1. Plug in wireless chime. To reduce

the risk of electrical shock, this equip-

ment has a polarized plug (one blade

is wider than the other).This plug will

ﬁt in a polarized outlet only one way. If

the plug does not ﬁt fully in the outlet,

reverse the plug. If it still does not ﬁt,

contact a qualiﬁed electrician to install

the proper outlet. Do not attempt to

bypass this safety feature.

Figure 1

Jumper Access Door

(See Tune or Code Section)

WARNING:To prevent possible

SERIOUS INJURY or DEATH:

 



 -



Chime Volume

Control

(Selected Chimes)

Wireless

plug-in

chime

Door sensor with battery,

Door magnet, Magnet spacer

Hardware

pack

Model

6168 ✔ ✔ ✔

6169 ✔ ✔

6170 ✔(x2) ✔

 The sensor must be mounted to the door jamb.The

magnet should be attached to the door. Sensor is for indoor use only.

This package includes (Style of door sensor and chime may vary from illustration):

-2- 200199-01

 

 Remove back of case by

pushing in tab on bottom with a small screw-

driver (see Figure 2).See diagram inside sensor

for correct battery orientation. Note: If batteries

are preinstalled, remove orange battery tab.

  The maximum gap

between sensor and magnet is 1/2" (13 mm)

(see Figure 4). The arrows located on the face

of each component must be aligned and facing

toward each other (see Figure 3).The magnet

must be beside the sensor. Note: If the magnet

is recessed, use spacer to ensure proper align-

ment (see Figure 3).

 Before mounting, hold sensor and

magnet in selected location and verify operation.

While holding the sensor still, move the magnet

away from the sensor to simulate door being

opened. Verify red LED on sensor ﬂashes mo-

mentarily and chime sounds.Note: If sensor does

not operate correctly, see Troubleshooting.

 

 Unplug chime and adjust volume

control to desired volume (see Figure 1). Plug

chime back into wall outlet.

Alignment Arrows

1/2" Maximum

Use Optional Spacer if

Needed

Figure 2

Figure 3

Figure 4

-3-200199-01

Use Optional

Spacer if Needed

6. Mount sensor.

 Remove back of case by

pushing in tab on bottom with a small screw-

driver (see Figure 2).Note: Remove material

in screw holes (if needed) before mounting

with screws. Attach sensor back cover to

wall using two short screws (provided).Snap

sensor onto back cover.

•   Apply foam tape to the

sensor back cover. Stick sensor back cover

to frame of door in desired position. Snap

sensor onto back cover.

 Repeat step 5 to attach magnet

(and spacer if needed) to door using two screws

(provided). Note: If using spacer, use the two

long screws (provided).

Figure 5

-4- 200199-01

Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong

(two note), or Westminster (eight note) (Available on selected chimes). The

factory setting is for the Ding-Dong tune (or Westminster, when available).This

tune can be changed by following the instructions below.

• Ding (one note tune)

Inside Sensor: Add a jumper to location 8.

• Ding-Dong (two note tune)

Inside Sensor: Remove jumper from location 8.

Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected chimes)

Inside Sensor: Remove jumper from location 8.

Chime: Add a jumper to location 8.

Note: All models have both front and back door tune capabilities. We recom-

mend the back door use the Ding tune and the front door use the Ding-Dong

tune (or Westminster tune, available on selected chimes). You may purchase

any Heath®/Zenith wireless push button for a second entrance.

  

      

reconnecting to power.

12345678

Inside

Sensor

Back of Chime

Tune Setting

Tune Setting (Not

used on all models)

Note: Some models might require the use of

tweezers to remove and replace the jumpers.

Figure 6

Remove screw to

open access door

Tune Settings

-5-200199-01

Troubleshooting



• Redlightonthesensordoesnotlight.

– Check orientation of sensor battery (See diagram inside sensor for

correct battery orientation.)

– Check charge of sensor battery, replace if necessary.

• Redlightonthesensordoeslight.

– Make sure sensor and chime codes are the same (see Figure 7).

– Make sure the plug-in chime has power going to it.

Chime is receiving

interference from another wireless device; change the code setting (see

Code Setting below).



• Donotmountthesensoronmetalornearmetalstuds.Thisreducesthe

sensor range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move the sen-

sor off the metal surface.

• Concreteoorsmayreducerange.Movechimeawayfromoor.

• Trylocatingchimeclosertosensor.



Continued

  

      

reconnecting to power.

It is recommended to only change one code position at a time and then check

to see if system is functioning properly.

1. Unplug chime from power source.

2. Open the cases and locate the jumpers on both the sensor and chime (see

Figure 7).

3. The sensor and chime both have eight different jumper locations. Jumper

positions 1 through 7 are used for setting the code.

-6- 200199-01

12345678

* Code Settings 1-7

Must Match Both

Sensor and Chime

Inside

Sensor

Remove

screw to open

access door

Back of Chime

4. To change the code, either:

• Addajumper to thesamelocationonboththe sensor andthechime

or...

• Removeajumper from thesamelocationonboththe sensor andthe

chime or...

• Moveajumperonthesensorfromonelocationtoanother.Movethecorre-

sponding jumper on the chime to match the new location in the sensor.

Example: Move jumper at location “5” to location “4” on both the sensor

and the chime.

Note:



Note: Unit will come factory set with jumpers in locations 5, 6, and 7 on the

sensor and on the chime.

The range of the wireless chime can vary with location, temperature, and

battery condition.

Note: Some models might require the use of

tweezers to remove and replace the jumpers.

HeathCo LLC reserves the right to discontinue and to change speciﬁcations at any time

without notice without incurring any obligation to incorporate new features in previously

sold products.

Figure 7

-7-200199-01



This device complies with Part 15 of the FCC Rules and RSS-210 of Industry

Canada.Operation is subject to the following two conditions:(1) this device may

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

The user is cautioned that changes or modiﬁcations not expressly approved by

the party responsible for regulatory compliance could void the user's authority

to operate the equipment.







If you experience a problem, follow this guide. You may also want to visit our

Web site at: www.hzsupport.com. If the problem persists, call* for assistance

at  8:00 AM to 5:00 PM CST (M-F).You may also write* to:

HeathCo LLC

P.O. Box 90045, Bowling Green, KY 42102-9045

ATTN: Technical Service

* If contacting Technical Service, please have the following information available:

Model Number, Date of Purchase, and Place of Purchase.



ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights.You may also have

other rights which vary from state to state or province to province.

For a period of one year from the date of purchase, any malfunction caused by factory

defective parts or workmanship will be corrected at no charge to you.

 Repair service, adjustment and calibration due to misuse, abuse or

negligence, light bulbs, batteries, and other expendable items are not covered by

this warranty. Unauthorized service or modiﬁcation of the product or of any furnished

component will void this warranty in its entirety. This warranty does not include

reimbursement for inconvenience, installation, setup time, loss of use, unauthorized

service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended to other

equipment and components that a customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR

CONDITION OF MERCHANT ABILITY ORTHAT THE PRODUCTS ARE FIT FOR ANY

PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL,

INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BETHE SOLE REMEDY OF THE CUSTOMER

AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR ANY

SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUD-

ING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER

OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. 



-8- 200199-01



Para reducir el riesgo de choque

eléctrico, este equipo tiene un enchufe

polarizado (una patilla es más ancha

que la otra).Este enchufe podrá inser-

tarse en un tomacorriente polarizado

solamente de una manera.Si el mismo

no entra completamente en el tomaco-

rriente, invierta el enchufe. Si aún no

encaja completamente, póngase en

contacto con un electrista competente

para qua éste instale el tomacorriente

correcto. No trate de suprimir esta

característica de seguridad.







  

   

MUERTE:

 



 -



Figura 1

Puerta de acceso al puente (Vea

la sección de Tonos o Códigos)

Control del

Volumen de

la Campana

(Campanas

seleccionadas)

Campana

inalámbrica

enchufable

Detector de puerta con batería, Imán

para la puerta, Espaciador del imán

Paquete de

ferretería

Modelo

6168 ✔ ✔ ✔

6169 ✔ ✔

6170 ✔(x2) ✔

Este paquete tiene (El estilo del detector de la puerta y el de la campana

pueden variar de la ilustración):

 El detector debe ser montado en el marco

de la puerta. El imán debe ser colocado en la puerta. El detector es sólo para

uso dentro de casa.

-9-200199-01

 

 Extraer la parte posterior

de la caja presionando la aleta en el botón con

un destornillador pequeño (vea la Figura 2).Vea

el diagrama dentro del detector para la correcta

orientación de la batería.

Nota: Si las baterías

están preinstaladas, quite la aleta anaranjada de

las baterías.



   El máximo

espacio entre el detector y el imán es de 13 mm

(vea la Figura 4). Las ﬂechas ubicadas en el

frente de cada componente deben alinearse y

mirarse unas a otras

(vea la Figura 3)

. El imán

debe estar junto al detector.Nota: Si el imán está

empotrado, use el espaciador para asegurar una

alineación correcta

(vea la Figura 3)

   Antes de montarlos,

sostenga el detector y el imán en el sitio

seleccionado y veriﬁque su funcionamiento.

Mientras sostiene el detector, mueva el imán

lejos del detector para simular una puerta que

se abre. Veriﬁque que el LED rojo del detector

se prenda y se apague momentáneamente y

que la campana suene. Nota: Si el detector no

funciona correctamente, vea la Guía de Análisis

de Averías.

 

 Desenchufe

la campana y ajuste el control del volumen al

volumen deseado (vea la Figura 1). Enchufe

de nuevo la campana en el tomacorriente de

la pared.

Flechas de alineación

13 mm Máximo

Use el espaciador

opcional si es necesario

Figura 2

Figura 3

Figura 4

Continúa

-10- 200199-01

Use el espaciador

opcional si es necesario

 

•   Extraer la parte

posterior de la caja presionando la aleta en

el botón con un destornillador pequeño (vea

la Figura 2). Nota: Quite la suciedad de los

oriﬁcios para tornillos (si es necesario) antes

de poner los tornillos. Fije la tapa posterior

del detector a la pared con los dos tornillos

pequeños (provistos). Presione el detector

sobre la tapa posterior.

•  Fije la cinta

adhesiva de espuma a la tapa posterior del

detector.Pegue la tapa posterior del detector

al marco de la puerta en la posición deseada.

Presione el detector sobre la tapa posterior.

  Repita el paso 5 para ﬁjar

el imán (y el espaciador si es necesario) a la

puerta con los dos tornillos (provistos). Nota: Si

usa el espaciador, use los dos tornillos largos

(provistos).

Figura 5

Andere Handbücher für 6168

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Heath Zenith Zubehör Handbücher

Heath Zenith

Heath Zenith DualBrite Bedienungsanleitung

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Bedienungsanleitung

Heath Zenith

Heath Zenith Notifi Elite Bedienungsanleitung

Heath Zenith

Heath Zenith Single Entrance Chime 23/M Bedienungsanleitung

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-06 Bedienungsanleitung

Heath Zenith

Heath Zenith HZ-1802-BK-A Bedienungsanleitung

Heath Zenith

Heath Zenith 598-1215-01 Bedienungsanleitung

Heath Zenith

Heath Zenith 7307 Bedienungsanleitung

Heath Zenith

Heath Zenith 6106 Bedienungsanleitung

Heath Zenith

Heath Zenith Replacement Motion Sensor SH-5407 Bedienungsanleitung

Heath Zenith

Heath Zenith SL-6155 Series Bedienungsanleitung

Heath Zenith

Heath Zenith 7309 Bedienungsanleitung

Heath Zenith

Heath Zenith 6180 Series Bedienungsanleitung

Heath Zenith

Heath Zenith 595-5684-09 Bedienungsanleitung

Heath Zenith

Heath Zenith Wireless Strobe Chime 6144 Bedienungsanleitung

Heath Zenith

Heath Zenith Decorative Wireless Chime 6180 Bedienungsanleitung

Heath Zenith

Heath Zenith Secure Home 5215 Bedienungsanleitung

Heath Zenith

Heath Zenith 7306 Bedienungsanleitung

Heath Zenith

Heath Zenith 29 Bedienungsanleitung

Heath Zenith

Heath Zenith Replacement Motion Sensor SL-5407 Bedienungsanleitung

Heath Zenith

Heath Zenith DualBrite Replacement Sensor Head 2LBN3 Service-Handbuch

Heath Zenith

Heath Zenith Wireless Mechanical Battery Operated Chime... Bedienungsanleitung

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-05 Bedienungsanleitung

Heath Zenith

Heath Zenith DualBrite 5716 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung