Herd C4 Series Bedienungsanleitung
1
Installation guide
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: S001
Rev: A
Date: 07-Jun-16
Important
Herd Bumpers are vehicle "Make & Model" specific. Use of a bumper on a vehicle other than the model it was
designed for will constitute improper use of the product and may void warranty.
Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these
instructions, OE hardware means the truck's original factory hardware.
For further detail of warranty coverage and warranty repair information visit www.HERD.com.
Product
Series
Slam Latch
C4
General Safety
Take time to fully read the instructions before installing the Slam Latch mechanism.
At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.
Parts and components of the Herd bumper can be heavy, handle with care to avoid injuries.
Respect power tools and use them as advertized.
For assistance call
1-888-543-4373
www.HERD.com
Thank you for choosing HERD!
HERD North America Inc.
2168 Springfield Road
Box 28, Group 525, RR5
Winnipeg, MB. Canada R2C 2Z2
Parts and tools referenced in this instruction
2
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: S001
Rev: A
Date: 07-Jun-16
Parts and hardware included
Tools Required
Tool
Specification
Ratchet
-
Torque wrench
-
Torque screwdriver
-
Socket
7/16” or 11 mm
Socket
1/2” or 13 mm
Wrench
7/16” or 11 mm
Wrench
1/2” or 13 mm
Hex drive
5/64” or 2 mm
Item No
Part No
Description
Qty
1
1SLA002
Slam Latch assembly
1
2
2HND002
Slam Latch handle
1
3
RHSN 0.25-20x1 FT SS 18-8
1/4”-20 X 1” carriage bolt, fully threaded, stainless steel
2
4
NLN 0.25-20 GR.5
1/4”-20 nylon lock hex nut, grade 5
2
5
FW 0.25 GR.5
1/4” flat washer, grade 5
2
6
HB 0.25-20x1 FT GR.5
1/4”-20 X 1” hex bolt, fully threaded, grade 5
8
7
HSLW 0.25
1/4” split lock washer
8
8
HB 0.3125-18x1.75 FT GR.5
5/16”-18 X 1-3/4” hex bolt, fully threaded, grade 5
2
9
6438K160
5/16”-18 clamp on shaft collar
2
1
2
3
5
4
6
8
7
9
Installation Procedure
3
Part No: S001
Rev: A
Date: 07-Jun-16
1-888-543-4373
www.HERD.com
1-888-543-4373
Important
Steps 1 through 5 document the installation procedure for the Herd Slam Latch. The Slam Latch requires
periodic adjustment. For instructions on how to properly adjust your Slam Latch, proceed to step 6.
1. Attach Slam Latch (Item 1) to
Herd bumper. Slam Latch must
be fastened on both driver side
and passenger side as shown.
Ensure that the Slam Latch may
still move forwards and
backwards with relative ease
after fastening.
Figure 1 –Slam Latch installation.
2. Hand tighten bolts until washers
may just barely spin freely. Do
not fully tighten bolts until
installation and adjustment is
complete.
Figure 2 –Slam Latch installation close-up (driver side shown).
6
7
1
6
1
7
Installation Procedure
4
Part No: S001
Rev: A
Date: 07-Jun-16
1-888-543-4373
www.HERD.com
1-888-543-4373
3. Install Slam Latch adjustment
screws (Item 8) on both driver
side and passenger side.
Adjustment screws are used to
adjust forward position of Slam
Latch.
Figure 3 –Slam Latch adjustment screw installation.
4. Position the shaft collar (Item 9)
inside the bumper between the
flange of the bumper and the
Slam Latch assembly (Item 1).
Feed the adjustment screw
(Item 8) through the hole in the
bumper and thread the screw
through the shaft collar and into
the threaded hole. Tighten the
clamping screw (Item A) on the
shaft collar to 19 ft-lbs of torque.
Ensure that the Slam Latch
assembly is in the most rear-ward
position.
Figure 4 –Slam Latch adjustment screw installation close-up (driver side shown)
with assembled side-view insert.
9
8
1
8
9
1
A
8
1
9
Installation Procedure
5
Part No: S001
Rev: A
Date: 07-Jun-16
1-888-543-4373
www.HERD.com
1-888-543-4373
5. Install the Slam Latch handle
(Item 2) to the Slam Latch
assembly. Feed carriage bolts
(Item 3) through handle and Slam
Latch assembly as shown. Fasten
on other side using supplied flat
washer (Item 5) and nylon lock
nut (Item 4).
Figure 5 –Slam Latch handle installation.
Important
The Herd Slam Latch requires adjustment. Proceed with the following steps for instructions on how to
properly adjust your Slam Latch.
6. If the Herd bumper is already
installed on a truck, open the
bumper. Loosen the 8 bolts
(Item 6) so that the washers
(Item 7) may just spin freely.
Figure 6 –Slam Latch adjustment (passenger side shown).
2
3
5
4
4
6
7
Installation Procedure
6
Part No: S001
Rev: A
Date: 07-Jun-16
1-888-543-4373
www.HERD.com
1-888-543-4373
7. Close the bumper. Turn the
adjustment screws (Item 8)
counter-clockwise until the latch
(Item B) on the Slam Latch
assembly sits flush against the
ramp (Item C) on the mounting
bracket. If the handle is too hard
to open, turn the adjustment
screws clockwise. This will loosen
the assembly. Adjust as necessary
until bumper can open/close
properly and all rattling
disappears.
Figure 7 –Slam Latch adjustment (passenger side shown) with side profile insert
and adjustment screw detail insert.
8. Open the bumper and tighten the
8 bolts (Item 6) from step 6 to
12 ft-lb of torque. Close the
bumper. The adjustment is now
complete.
Figure 8 –Slam Latch mounting bolts (passenger side shown).
C
CW
CCW
8
B
TIGHTENING
LOOSENING
C
B
8
8
12 ft-lb
Inhaltsverzeichnis
Andere Herd Autozubehör Handbücher
Herd
Herd AeroPLUS C4-02 Leitfaden
Herd
Herd IN27BG Bedienungsanleitung
Herd
Herd MK15C4-02 Bedienungsanleitung
Herd
Herd Defender Series Bedienungsanleitung
Herd
Herd KW22C4-02 Bedienungsanleitung
Herd
Herd SLAM LATCH Leitfaden
Herd
Herd Aero Bedienungsanleitung
Herd
Herd 404006 Bedienungsanleitung
Herd
Herd Aero Bedienungsanleitung
Herd
Herd Aero Series Bedienungsanleitung
