Herd IN24A2 Bedienungsanleitung

Installation guide

1-888-543-4373

www.HERD.com

1-888-543-4373

Part No: IN24-IG

Rev: A

Date:28-Nov-16

Important

Herd Bumpers are vehicle "Make & Model" specific. Use of a bumper on a vehicle other than the model it was

designed for will constitute improper use of the product and may void warranty.

Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these

instructions, OE hardware means the truck's original factory hardware.

For further detail of warranty coverage and warranty repair information visit www.HERD.com.

SKU #

Truck Model

IN24A2, IN25A2, IN24A4,

IN25A4, IN24D2, IN25D2,

IN24D4, IN25D4,

IN24DFLT2, IN25DFLT2,

IN24RT, IN25RT, IN24TX4,

IN24BTX4, IN24SRT

International

HX520 SFA,

HX615/620 SBA

General Safety

Take time to fully read the instructions before installing the Herd bumper.

At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.

Parts and components of the Herd bumper can be heavy, handle with care to avoid injuries.

Respect power tools and use them as advertised.

For assistance call

1-888-543-4373

www.HERD.com

Thank you for choosing HERD!

HERD North America Inc.

2168 Springfield Road

Box 28, Group 525, RR5

Winnipeg, MB. Canada R2C 2Z2

IN24SRT SHOWN

Parts and tools referenced in this instruction

1-888-543-4373

www.HERD.com

1-888-543-4373

Part No: IN24-IG

Rev: A

Date:28-Nov-16

Parts and hardware included (IN24 Bumper shown)

Tools Required

Tool

Specification

Socket

¾” or 19 mm

Socket

15/16” or 24 mm

Socket

11/8” or 30 mm

Wrench

¾” or 19 mm

Wrench

15/16” or 24 mm

Wrench

11/8” or 30 mm

Item No

Part No

Description

Qty

IN24/IN25 BUMPER

Bumper, IN HX 520/615/620

BR-IN24/BR-IN25

Bracket, IN HX 520/615/620

1-BR-PAC-51X9.5

Packer, 51 mm x 51 mm, 3/8” thick

1MPA036

Center Mount, IN24

1MPA037

Nut Plate, IN24

HB0.625-11X3.25GR8

Hex Bolt - 5/8”-11x3.25” Grade 8

HB0.625-11X2FTGR8

Hex Bolt - 5/8”-11x2”Fully Thr. Grade 8

HB0.5-13X2GR8

Hex Bolt - 1/2”-13x2” Grade 8

NLN0.625-11GR8

Hex Nylon Lock nut -5/8”-11 Grade 8

FW0.5GR8

Flat Washer - ½” Grade 8

FW0.625GR8

Flat Washer - 5/8” Grade 8

W-8SH

Shim, 1/16È thick

1MP060

Shim, 3/8” thick, 5/8” bolt (IN25 only)

Installation Procedure

1-888-543-4373

www.HERD.com

1-888-543-4373

Part No: IN24-IG

Rev: A

Date:28-Nov-16

1. Unplug driving lights (if

equipped). Remove front bumper

bolts.

Figure 1

2. Disconnect torsion bar (IN25 set

back axle only). Remove OEM

bumper.

Figure 2

3. Install center mount (Item 4)

onto cross member as shown in

Figure 3.

Figure 3 –Center mount installation.

Cross member

Remove these bolts

Remove this bolt

Installation Procedure

Part No: IN24-IG

Rev: A

Date: 28-Nov-16

1-888-543-4373

www.HERD.com

1-888-543-4373

4. Open bumper. Using crane, lift

the bumper (Item 1) and bracket

(Item 2) and attach to Herd

Center Mount (Figure 4a) and

tow receiver casting (Figure 4b).

Use supplied shims (Item 12 or

13) to close gap between the

Center Mount (Item 4) and

bracket (Item 2) if required.

Note:

If installer does not have a crane

available, bumper can be

disassembled from the bracket to

simplify installation as shown in

step 5, otherwise proceed to step

Figure 4a –Herd bracket attached to center mount.

Figure 4b –Herd bracket attached to tow receiver casting.

Tow receiver

casting

Installation Procedure

Part No: IN24-IG

Rev: A

Date: 28-Nov-16

1-888-543-4373

www.HERD.com

1-888-543-4373

5. To disassemble bracket from the

bumper remove both hinge bolts.

Note:

If bumper is equipped with lift

assist the springs must be

removed. Refer to instructions

S004 (Defender bumpers) or S005

(Aero/Texas bumpers) for proper

lift assist disassembly procedure.

Figure 5 - Bumper disassembly (Aero bumper shown).

6. If equipped with OEM fog lights,

remove driving lights from

factory bumper and retain OEM

hardware. Reinstall onto Herd

bumper using the preinstalled

driving light brackets on both

driver and passenger side.

Figure 5 –OEM Fog Light installation.

7. Close the bumper and check the

fitment. Bumper position can

be adjusted side to side and up

/ down as required. Once

fitment confirmed tighten all

bolts.

Figure 6 –Bolt torque specs (Driver side shown).

Important

Check mounting points after the first 5000 km and every 3-6 month.

If bumper is equipped with Herd Slam Latch, periodic adjustment is required. Refer to Slam Latch Installation

adjustment instructions to properly adjust your Slam Latch.

110 ft-lb

6 Bolts

Hinge bolts

OEM Hardware

Fog Light

210 ft-lb

4 Bolts

210 ft-lb

4 Bolts

110 ft-lb

4 bolts

Dieses Handbuch passt für folgende Modelle

Andere Herd Autozubehör Handbücher

Herd

Herd PB11C4-02 Bedienungsanleitung

Herd

Herd C4 Series Bedienungsanleitung

Herd

Herd Aero Bedienungsanleitung

Herd

Herd SLAM LATCH Leitfaden

Herd

Herd 404006 Bedienungsanleitung

Herd

Herd KW22C4-02 Bedienungsanleitung

Herd

Herd KW01 Bedienungsanleitung

Herd

Herd MK15C4-02 Bedienungsanleitung

Herd

Herd IN27BG Bedienungsanleitung

Herd

Herd WS30C4-02 Bedienungs- und Wartungshandbuch

Herd

Herd Aero Series Bedienungsanleitung

Herd

Herd Aero Bedienungsanleitung

Herd

Herd Defender Series Bedienungsanleitung

Herd

Herd FL33BG Bedienungsanleitung

Herd

Herd AeroPLUS C4-02 Leitfaden

Herd

Herd Aero Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung