HIK VISION 7216HVI-S Bedienungsanleitung

Quick Start Guide

DS-7208 & 7216HVI-S Series DVR

Quick Start Guide - DS-7208 & 7216HVI-S Series DVR 1

Menu Structure

The menu structure of the DS-7208HVI-S & 7216HVI-S

Series DVR is as followed:

Startup and Shutdown

Proper startup and shutdown procedures are crucial to

expanding the life of your DVR.

To startup your DVR:

1. Ensure the power supply is plugged into an electrical

outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) is used in

conjunction with the unit.

2. Turn on the switch on rear panel. The Status indicator

LED should turn green. The unit will begin to start.

3. After startup, the Power indicator LED will remain

Green.

There are two proper ways to shutdown the DVR. To

shutdown the DVR:

• OPTION 1: Standard Shutdown

1. Enter the Shutdown menu by clicking on Menu >

Shut down.

2. Select the Shutdown button.

3. Message “Please close power!”will pop up

4. Turn off switch on rear panel

• OPTION 2: Manual Shutdown

1. Press and hold the POWER button for 3 seconds.

2. Enter the administrator‟s username and password in the

dialog box for authentication.

3. Message “Are you sure to turn off DVR?”will popup.

4. Click “Yes”then message “Please close power”will

pop up

5. Turn off switch on rear panel

Note: Do not press the POWER button again when the

system is shutting down.

Using the Setup Wizard

By default, the

Setup Wizard will

start once the

DVR has loaded.

The Setup Wizard

will walk you

through some of

the more important settings of your DVR. If you do not

wish to use the Setup Wizard at this time, click the Cancel

button. You may also choose to use the Setup Wizard at a

later time by leaving the “Start Wizard when DVR starts?”

checkbox checked.

To start using the Setup Wizard:

2 Quick Start Guide - DS-7208 & 7216HVI-S Series DVR

1. Click the Next button

on the Wizard window.

This will take you to

the User Permission

window.

2. Navigate to the Admin

Password input field.

3. Enter the admin password into the Admin Password input

field. By default, the password is 12345.

4. To change the admin password, check the New Admin

Password checkbox. Enter the new password and confirm

the password in the given fields.

5. Click the Next button.

This will take you to

the HDD Management

window.

6. To start HDD

management, click the

Enter button.

7. If a new HDD was recently installed, select the HDD from

the list to initialize it.

Initializing the HDD

will format and

remove all data from

it.

8. After the HDD has

been initialized, click

the OK button which will take you back to the Setup Wizard

window.

9. Click the Next button.

This will take you to

the Record Settings

Window.

10. To enter the Record

Settings window, click

the Enter button.

11. Select the Schedule tab.

12. Click the Edit button.

This will open up a new recording schedule.

13. Check both the

Enable Schedule and

All Day checkbox. This

will enable the

recording schedule and

have it record

continuously all day.

14. Click the OK button.

This will take you back to the Schedule tab. To copy the

schedule to a different channel, select the channel or all

under Copy To and

click the Copy button.

15. Click the Next button.

This will take you to the

Network Settings

window.

16. To configure network

settings, click the Enter

button.

17. Enter the IP Address,

Subnet Mask and

Default Gateway.

18. Click the OK button to

return to the Setup Wizard.

19. If all the settings are entered as desired, click the Done

button to finish and exit the Setup Wizard.

Quick Start Guide - DS-7208 & 7216HVI-S Series DVR 3

Congratulations! You‟ve completed the Setup Wizard. The

next step in the initial setup process is to setup the system

date and time.

Setting Date & Time

It is extremely important to setup the system date and time to

accurately timestamp recordings and events.

To setup date and

time:

1. Enter General

Settings menu by

clicking Menu

> Setting >

General.

2. Enter the correct date and time under System Time.

3. Click the Apply button to save the setting.

Playback

Playback from Search

To playback files from a video search:

1. Enter into the Video Search menu by clicking Menu >

Video Search.

2. Set the search parameters

by selecting cameras to

search, video/file type and

the start/end time.

3. Click the Play button to

start playback of all the

files found with the

specified search criteria

or click the Search

button to bring up the list

of search results. After search results are presented, select the file

you would like to playback and press Play.

4. Recordings will

automatically be

playbacked in

the Playback

interface.

Playback from Live Preview

You may also instantly playback from a channel while

watching a Live Preview. The playback will be of recordings

from the past 5 minutes.

To playback from a channel instantly in Live Preview:

• Using a Mouse:

1. Right-click the mouse on desired channel and select the

Playback button.

2. Recordings from the selected channel will start playing

back in the Playback interface. An Attention message

will appear if there are no recordings found from the

previous 5 minutes. You may also press the Play button

to view the day‟s recording for the selected channel.

3. You may also select additional channels for playback

from the channel list on the right hand side of the

Playback interface.

• Using the Front Panel/Remote:

1. Press the PLAY button. This will take you into the

Playback interface.

2. Enter the channel you would like to watch recordings

for on the front panel or remote (i.e. press „11‟ for channel

11).

3. Recordings will begin for the selected channel.

4 Quick Start Guide - DS-7208 & 7216HVI-S Series DVR

Playback from System Log

You may also playback recordings from the System Log.

To playback video from the System Log:

1. Enter the Log Search menu by clicking Menu>

Maintenance > Log Search.

2. Set Major Type setting to Information.

3. Set Minor Type setting to Start Record or End Record.

4. Set Start Time and End Time.

5. Click the Search button.

6. A list of results with your search criteria will be displayed.

Select the video log to playback and click Play.

7. The recording will begin to play in the Playback interface.

Backup

Recorded files can be backed up to various devices, such as

USB flash drives, USB HDDs or a DVD writer.

To export recorded files:

1. Enter the Export Video menu by clicking Menu > Video

Export.

2. Select desired parameters to search for files to export.

3. Press the Export button. This will take you to the Video

Search menu.

4. Select the files to export.

You may also click the Play button to verify that these files

are indeed the ones you would like to export.

5. The size of the currently selected files is displayed in the

lower-left corner of the window. Select the Next button to

enter the Export menu.

6. Select device to export to from drop-down list (USB Flash

Drive, USB HDD, and DVD Writer). If backup device is not

recognized:

• Click the Refresh button.

• Reconnect device.

• Check for compatibility from vendor.

7. Click Start to begin backup process.

8. After the backup process has completed, you may select

the files from your device and click the Play button to verify

that it has been exported successfully.

Note: Video Player software will automatically be copied

on to the device that the recorded files were exported on.

Quick Start Guide - DS-7208 & 7216HVI-S Series DVR 5

Using the Front Panel Controls

Figure 4. DVR Front Panel Controls

The controls on the front panel include:

1. USB Ports: Universal Serial Bus (USB) ports for additional devices such as USB mouse and

USB Hard Disk Drive (HDD).

2. Status Indicators: Status indicators for different features of the DVR.

• Alarm: Alarm indicator turns red when a sensor alarm is detected.

• Ready: Ready indicator turns green when DVR is functioning properly.

• Status: Status indicator turns green when DVR is controlled by an IR remote.

• HDD: HDD indicator blinks red when data is being read from or written to HDD.

• NETWORK: NETWORK indictor blinks blue when network connection is functioning

properly.

3. Control Buttons:

• 1/MENU Button: The 1/MENU button works as numeric [1]. Pressing this button will return

the user to the Main menu (after successful login). The 1/MENU button will also bring up

Sensitivity Interface settings.

• 2ABC/F1: The 2ABC/F1 button works as numeric [2] and letter [ABC]. When it is used in a

list field will select all items on the list.

• 3DEF/F2: The 3DEF/F2 button works as numeric [3] and letter [DEF]. It is also used to cycle

through tab pages.

• 4GHI/ESC: The 4GHI/ESC button works as numeric [4] and letter [GHI], it is also used to

6 Quick Start Guide - DS-7208 & 7216HVI-S Series DVR

escape to the previous menu

• 5JKL/EDIT: The 5JKL/EDIT button works as numeric [5] and letter [JKL]. The 5JKL/EDIT

button is used to edit text fields. When editing text fields, it will also function as a Backspace

button to delete the character in front of the cursor. On checkbox fields, pressing the

5JKL/EDIT button will tick the checkbox. In Playback mode, it can be used to generate video

clips for backup.

• 6MNO/PLAY: The 6MNO/PLAY button works as numeric [6] and letter [MNO]. It is used to

enter the Playback menu. It is also used to turn audio on/off in the Playback menu.

• 7PQRS/REC: The 7PQRS/REC button works as numeric [7] and letter [PQRS]. It is also used

to enter the Manual Record interface.

• 8TUV/PTZ: The 8TUV/PTZ button works as numeric [8] and letter [TUV]. It is also used to

enter the PTZ Control mode.

• 9WXYZ/PREVIEW: The 9WXYZ/PREVIEW button works as numeric [9] and letter

[WXYZ]. It is also used to switch between single screen and multi-screen mode.

• 0/A: The 0/A button works as numeric [0]. It is also used to switch between input methods

(upper and lowercase alphabet, symbols and numeric input). It can also be used to clear entire

masked areas, such as in the Motion Detection and Privacy Mask menus.

•SHIFT: The SHIFT button is used for switch button action between numeric button and

control button.

4. DIRECTION/ENTER Buttons:

• DIRECTION Buttons: The DIRECTION buttons are used to navigate between different fields

and items in menus. In Playback mode, the Up and Down button is used to speed up and slow

down recorded video. The Left and Right button will jump 30s backward and forward in a

video. In Preview mode, these buttons can be used to cycle through channels.

• ENTER Button: The ENTER button is used to confirm selection in any of the menu modes. It

can also be used to tick checkbox fields. In Playback mode, it can be used to play or pause the

video. In Single Play mode, pressing the ENTER button will advance the video by a single

frame.

5. IR Receiver: Receiver for IR remote.

Note: It is important to note that you must click the EDIT button on either the remote or front panel on a text

field before you‟re able to edit its content. After you‟re done entering text, you must hit the ENTER button to be

able to move on to the next field.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION DVR Handbücher

HIK VISION

HIK VISION DS-7208HTI-K2 Bedienungsanleitung

HIK VISION

HIK VISION DS-9104HFI-S Bedienungsanleitung

HIK VISION

HIK VISION iVMS-4200 Bedienungsanleitung

HIK VISION

HIK VISION DS-9500 Series NVR Bedienungsanleitung

HIK VISION

HIK VISION DS-9100HWI-ST Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7104HWI-SL Series Bedienungsanleitung

HIK VISION

HIK VISION C Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7600 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7604 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7304HUI-K4 Bedienungsanleitung

HIK VISION

HIK VISION DS-7104HGHI-SH Bedienungsanleitung

HIK VISION

HIK VISION DS-7004HI-S Bedienungsanleitung

HIK VISION

HIK VISION DS-MP7516 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-8100-S Series Bedienungsanleitung

HIK VISION

HIK VISION DS-90 HUHI-F8/N Series Bedienungsanleitung

HIK VISION

HIK VISION DS-MP7608H Bedienungsanleitung

HIK VISION

HIK VISION DS-7204HVI-S Series Bedienungsanleitung

HIK VISION

HIK VISION DS-8100HFI-ST Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7200-SH Bedienungsanleitung

HIK VISION

HIK VISION DS-7104NI-Q1 Bedienungsanleitung

HIK VISION

HIK VISION DS-8100HFI-ST Series Bedienungsanleitung

HIK VISION

HIK VISION DS-8000HTI-S Series Bedienungsanleitung

HIK VISION

HIK VISION DS-9000HFI-RH Series Bedienungsanleitung

HIK VISION

HIK VISION DS-8000AHI-S/AHLI-S Series Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

FSM

FSM Colibri Grande PRO Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung