Honeywell DR 4300 Leitfaden

Form 43-DR-33-75 Page 1 of 3

Model DR 4300

Circular Chart Recorder

Replacement Instruction

Digital Input Printed Wiring Assembly (51404566-501)

Document Number Form: 43-DR-33-75

Effective: 3/98

Supersedes: None

Kit Contents This kit contains a Digital Input Printed Circuit Board.

Summary Enclosed is a new digital input board for your DR4300 recorder. Use the

following procedure to install the new board in your recorder.

WARNING Never access components inside the case with power applied.

Continued next page

Kit Instruction, continued

Page 2 of 3 Form 43-DR-33-75

Component Location Refer to Figure 1 for the component locations and Table 1 for the

installation procedure.

24225

Digital

Input

Board

Main

Board

Terminal Ground

on Main Board

TB1

Stand-offs

Figure 1 – Component Location

Kit Instruction, continued

Form 43-DR-33-75 Page 3 of 3

Installation Procedure Follow the procedure in Table 1 to install the new digital input printed

wiring assembly in your recorder.

Table 1 – Digital Input PWA Installation

Step Action

1Power down the recorder. Open the chart door and swing the

chart plate out. This permits access to the Main printed

circuit board.

2 Locate the Digital Input printed circuit assembly (PCA)

mounted on top of the pen channel’s printed circuit assembly

on three plastic stand-offs.

3 Disconnect the field wiring from P30 on the old digital input

PCA.

4 Disconnect the power cable from J9 on the old digital input

PCA. You can leave it attached to J13 on the main PCA

unless you are also replacing the cable.

5 Disconnect the processor interface cable from P7 on the old

digital input PCA. You can leave it attached to J10 on the

main PCA unless you are also replacing the cable.

6 Loosen the digital input ground wire (WG) from the ground

terminal located on the main PCA.

7 To remove the old digital input PCA, use needle-nose pliers

to squeeze together the split top of the stand-off on the left

and slide the PCA off the stand-off. Repeat for the center and

right stand-offs.

8 Position the new digital input PCA on the stand-offs and

press it into place.

9 Replace the cable plugs, terminal block, and ground wire

disconnected in Steps 3 through 6.

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell AUTOCUBE 8200 Bedienungsanleitung

Honeywell

Honeywell Multiple Meter Units Bedienungsanleitung

Honeywell

Honeywell TE923W - Deluxe Weather Station Bedienungsanleitung

Honeywell

Honeywell BendixKing KN 62A Bedienungsanleitung

Honeywell

Honeywell APT4000PH Bedienungsanleitung

Honeywell

Honeywell RMA300-ME Bedienungsanleitung

Honeywell

Honeywell Morley-IAS MI-IM10 Bedienungsanleitung

Honeywell

Honeywell FlexLine SmartServo 954 Bedienungsanleitung

Honeywell

Honeywell HERMetic UTImeter Gtex Chem Bedienungsanleitung

Honeywell

Honeywell ACM 150 Betriebsanleitung

Honeywell

Honeywell HG1120 Bedienungsanleitung

Honeywell

Honeywell W8710A Bedienungsanleitung

Honeywell

Honeywell MagneW 3000 Plus Benutzerhandbuch

Honeywell

Honeywell E3Point Bedienungsanleitung

Honeywell

Honeywell FS20X Series Bedienungsanleitung

Honeywell

Honeywell LeaderLine DPR 100 C Bedienungsanleitung

Honeywell

Honeywell GENT S4-34 Series Gebrauchsanweisung

Honeywell

Honeywell DR4300 Series Leitfaden

Honeywell

Honeywell NOTIFIER UDS-3 Verdrahtungsschema

Honeywell

Honeywell AD1200-CT Bedienungsanleitung

Honeywell

Honeywell OELD Bedienungsanleitung

Honeywell

Honeywell SX Bedienungsanleitung

Honeywell

Honeywell NK Bedienungsanleitung

Honeywell

Honeywell FE260 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung