Honeywell SX Bedienungsanleitung

43-TV-33-72 iss.2 GLO Jan 21 UK 1

SX Recorder - Installation Instruction

Inverter and cable

SX Recorder

This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up

functionality in the recorder. Refer to the User manual for detailed operational requirements.

The SX Recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If unsure, please

return the unit to your supplier for repair or upgrade.

Removing the case and opening the back of the recorder should only be performed under the following circumstances:

When an item of hardware requires individual replacement.

When an item of hardware is to be retrospectively fitted.

In all other instances it is recommended that the complete unit be returned to an authorised agent or service centre.

For Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility

WARNING

HAZARDOUS VOLTAGES

Disconnect all power to the recorder before removing the case and attempting any maintenance procedures.

SAFETY TESTS

Upon completion of service procedures detailed in this manual two basic safety tests should be performed in order to

ensure continued safe operation of the instrument.

Earth Resistance; 25 VDC applied between case and protective earth, bonding resistance should be < 0.1 Ohm.

Insulation Resistance; 500Vdc applied between the earth terminal, and the live and neutral terminal shorted together,

insulation resistance to be >2.0 MOhm. (Mega Ohm, NOT milli Ohm)

Failure to comply with these instructions could result in death or serious injury

CAUTION

OBSERVE ANTI-STATIC PRECAUTIONS

Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices.

Full anti-static precautions MUST be observed when in contact with the electronics of your recorder.

SAVE DATA, SETUPS AND LAYOUTS

Removal of PCBs and battery back-up will result in the loss of all non-volatile data.

Ensure all data and set-ups are saved.

Failure to comply with these instructions may result in product damage.

43-TV-33-72 iss.2 GLO Jan 21 UK 2

Before attempting to repair or upgrade a recorder, it is advisable to clear a sufficient work space so components such as

the front panel can be rested on the work surface without getting scratched or damaged.

Panel Mounting

Before a new Inverter can be fitted the recorder must be removed from the panel. Loosen the mounting clamp screws,

slide the clamp towards the rear of the recorder and remove the clamps and the recorder.

Removing the Touch Screen Assembly

To fit a new Inverter the case and back panel must be removed. The case and back panel can be removed as a single

assembly. Remove the 2 screws on each side of the case as shown in Fig 1 below

Slide the case and rear panel assembly off the recorder.

Fig 1

Remove 2 screws from

each side of the case

Fig 2

43-TV-33-72 iss.2 GLO Jan 21 UK 3

Once the case has been removed all the boards must be removed with the exception of the processor board. Fig 3

To release all the I/O boards loosen the screws down the side of the recorder that lock the boards in place. Remove the

boards by pulling towards the back of the recorder.

Ensure a note is made of where the boards came from, the boards will need to be replaced in exactly the same slots.

The power supply must also be removed in the same way, the securing screw is on the other side of the recorder.

Fig 3

Power

Supply

Loosen

Screw

Withdraw

boards

Fig 4

Speaker

cable

Mother

Board

43-TV-33-72 iss.2 GLO Jan 21 UK 4

Disconnect the speaker cable from the Mother Board.

Once all the cards have been removed and the speaker cable is disconnected the Mother board can be extracted by

pulling upwards to disconnect from the Processor Board. See fig 4 above.

Place the recorder face down, ensuring the front face is not going to get scratched or damaged.

The inverter is now accessible. Disconnect the high voltage lead from the inverter (See Fig 5). Disconnect the inverter

lead from the processor board.

Undo the two M2 nuts that hold the inverter in place, remove the nuts and shakeproof washer. Lift the inverter clear of

the mounting screws.

Fig 5

High voltage

lead

M2 nuts

43-TV-33-72 iss.2 GLO Jan 21 UK 5

Fitting the new inverter

The new inverter can be fitted onto the screws. Make sure the plastic spacers are still in position on the screws before

the inverter is fitted.

Fit the M2 shakeproof washers and nuts to the screws and secure the inverter in place.

The inverter lead should be threaded through the square hole in the central chassis partition. See Fig 6. Plug the

inverter cable into the processor board. The connector is polarised, so must be fitted in the correct orientation.

Plug the Mother Board back into the vertical board guides, ensure it is properly seated on the processor board.

Refit all the I/O boards and the power supply in the same slots as they originally occupied. Tighten up the retaining

screws that secure the boards into the chassis.

Slide the case back onto the recorder ensuring it is fitted the right way round. The cooling slots should be at the top of

the unit.

Finally fit the four M4 screws that hold the case to the chassis.

Copyrighted Materials. For more information please contact your supplier.

Fig 6

Thread cable

through hole.

Andere Handbücher für SX

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell FlexLine SmartServo 954 Bedienungsanleitung

Honeywell

Honeywell DR 4300 Leitfaden

Honeywell

Honeywell QX Bedienungsanleitung

Honeywell

Honeywell HomMed Genesis Touch Bedienungsanleitung

Honeywell

Honeywell CM4 Bedienungsanleitung

Honeywell

Honeywell Vertex Bedienungsanleitung

Honeywell

Honeywell E-Mon Class 1000 Bedienungsanleitung

Honeywell

Honeywell RM640 Bedienungsanleitung

Honeywell

Honeywell W8600B Bedienungsanleitung

Honeywell

Honeywell AUTOCUBE 8200 Bedienungsanleitung

Honeywell

Honeywell DR Graphic Bedienungsanleitung

Honeywell

Honeywell 04973 Series Handbuch

Honeywell

Honeywell Themis alpha EI2 Betriebsanleitung

Honeywell

Honeywell MiniRAE 3000+ Bedienungsanleitung

Honeywell

Honeywell UDA2182 Bedienungsanleitung

Honeywell

Honeywell EK205 Bedienungsanleitung

Honeywell

Honeywell HERMetic UTImeter Gtex Chem IIC Bedienungsanleitung

Honeywell

Honeywell DR4300 Series Leitfaden

Honeywell

Honeywell AirAlert 96d Handbuch

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Bedienungsanleitung

Honeywell

Honeywell QX Series Bedienungsanleitung

Honeywell

Honeywell RABO G16 Bedienungsanleitung

Honeywell

Honeywell NK Bedienungsanleitung

Honeywell

Honeywell E-Mon Anleitung zur Verwendung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung