Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

FocusPRO®TH6000 Series

Programmable Thermostat

® U.S. Registered Trademark. Patents pending.

Installation

Guide

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions

can damage the product or cause a hazardous condition.

Need Help?

For assistance with this product please visit http://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

69-2695EFS-01

This manual covers the following models

• TH6110D:For1Heat/1Coolsystems

• TH6220D:Forupto2Heat/2Coolsystems

• TH6320U:Forupto3Heat/2Coolsystems

(Remove battery holder to find model number)

System Types

• Gas,oil,orelectricheatwithair

conditioning

• Warmair,hotwater,high-efficiency

furnaces,heatpumps,steam,

gravity

• Heatonly—two-wiresystems,

three-wirezonevalves(Series20),

and normally open zone valves

• Heatonlywithfan

• Coolonly

• 750mVheatingsystems

Installation Guide

69-2695EFS— 01 2

ENGLISH

MCR29435

M29433

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Drill3/16"holesfordrywall.Drill7/32"holesforplaster.

Wallanchors

Wallplate

Wirehole

Mounting screws

CAUTION: ELECTRICAL HAZARD

Cancauseelectricalshockorequipmentdamage.Disconnectpowerbefore

beginning installation.

MERCURY NOTICE

Ifthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donot

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Pull here to remove wallplate

from new thermostat.

Remove battery holder. Insert reference card after wallplate is

mounted(seeinstructions,below).

It's easier to grasp the wallplate

and remove it after completely

removing the battery holder.

MCR29434

FocusPRO®TH6000 Series

3 69-2695EFS— 01

ENGLISH

MCR29436

Power options

Keep wires in this

shaded area

Connect Cfor primary AC power

(optional if batteries are installed).

Insert batteries for primary

or backup power.

Remove factory-

installed jumper

only for two-

transformer

systems.

Conventional Terminals:

Rc 24VACpowerfromcooling

transformer

R24VACpowerfromheating

transformer

WHeat relay (stage 1)

W2 Heat relay (stage 2)

Y Compressor contactor (stage 1)

Y2 Compressor contactor (stage 2)

G Fan relay

C24VACcommon.For2transformer

systems,usecommonwirefromcooling

transformer.

Heat Pump Terminals:

Rc 24VACpowerfromcooling

transformer

R24VACpowerfromheating

transformer

O/B Changeover valve

YCompressor contactor (stage 1)

Y2 Compressor contactor (stage 2)

-TH6320U only

G Fan relay

Aux/E Auxiliary/Emergency heat relay

LSends output when set to Em. Heat

C 24VACcommon

Wiring

Terminal designations

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

TH6110D

RcYWGRC

TH6220D

RcYWGW2Y2 RC

TH6320U

RcYWGW2Y2 RC

MCR29437A

TH6110D

RcYGRC

RcY

TH6220D

RcYGAux

TH6320U

MCR29438A

Aux

Installation Guide

69-2695EFS— 01 4

ENGLISH

Wiring

Wiring guide — conventional systems

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

NOTES

Wirespecifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means and

overload protection as required.

[2] Remove jumper for 2-transformer systems.

 [3] Optional24VACcommonconnection.

[4] Common connection must come from cooling

transformer.

[5] InInstallerSetup,setsystemtypetoHeat Only.

[6] InInstallerSetup,setsystemtypeto

2Heat/2Cool Conventional.

 [7] InInstallerSetup,setchangeovervalvetoO

or B.

[8] InInstallerSetup,setsystemtypeto

2Heat/1Cool Heat Pump.

[9] InInstallerSetup,setsystemtypeto

2Heat/2Cool Heat Pump.

[10] InInstallerSetup,setsystemtypeto

3Heat/2CoolHeatPump.

[11] L terminal sends a continuous output when

thermostat is set to Em. Heat. Connect to

Honeywell zoning panels to switch the panel to

Emergency Heat.

1H/1C System

(1 transformer)

Rc Power [1]

R[R+Rc joined by jumper]

YCompressor contactor

C 24VACcommon[3]

W Heat relay

GFan relay

Heat-only System

Rc Power [1]

R[R+Rc joined by jumper]

C 24VACcommon[3]

W Heat relay

Heat-only System

(Series 20) [5]

Rc [R+Rc joined by jumper]

RSeries 20 valve terminal “R” [1]

Y Series20valveterminal“W”

C 24VACcommon[3]

W Series 20 valve terminal “B”

Heat-only System

(normally open zone valve) [5]

Rc [R+Rc joined by jumper]

RPower

[1]

Y Normally open zone valve

C 24VACcommon[3]

1H/1C System

(2 transformers)

Rc Power (cooling transformer) [1,2]

RPower (heating transformer) [1,2]

YCompressor contactor

C 24VACcommon[3,4]

W Heat relay

GFan relay

Heat-only System

with Fan

Rc Power [1]

R[R+Rc joined by jumper]

C 24VACcommon[3]

WHeat relay

GFan relay

Cool-only System

Rc Power [1]

R[R+Rc joined by jumper]

YCompressor contactor

C 24VACcommon[3]

G Fan relay

2H/2C System

(1 transformer) [6]

Rc Power [1]

R[R+Rc joined by jumper]

YCompressor contactor (stage 1)

C 24VACcommon[3]

WHeat relay (stage 1)

GFan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers) [6]

Rc Power (cooling transformer)[1,2]

RPower (heating transformer) [1,2]

YCompressor contactor (stage 1)

C 24VACcommon[3,4]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

RcYWG RC

MCR29439

MCR29440

RcY

MCR29441

RcYRC

MCR29442

RcWG RC

MCR29444

RcYG RC

MCR29445

RcYWGW2Y2 RC

MCR29446

RcYWG RC

M29443

RcYWGW2Y2 RC

M29447

FocusPRO®TH6000 Series

5 69-2695EFS— 01

ENGLISH

MCR29453

Wiring

Wiring guide — heat pump systems

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

Thermostat mounting

Align the 4 tabs on the wallplate with

slotsonthebackofthethermostat,

then push gently until the thermostat

snaps in place.

Push excess wire back into

the wall opening.

Plug wall opening with

non-flammable insulation.

1H/1C Heat

Pump System

Rc Power [1]

R[R+Rc joined by jumper]

YCompressor contactor

C 24VACcommon[3]

O/B Changeover valve [7]

G Fan relay

2H/1C Heat

Pump System

(TH6220D only) [8]

Rc Power [1]

R[R+Rc joined by jumper]

YCompressor contactor

C 24VACcommon[3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

L Sends output when set to Em. Heat [11]

2H/1C Heat

Pump System

(TH6320U only) [8]

Rc Power [1]

R[R+Rc joined by jumper]

YCompressor contactor

C 24VACcommon[3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

LSends output when set to Em. Heat [11]

2H/2C Heat

Pump System

(TH6320U only) [9]

Rc Power [1]

R [R+Rc joined by jumper]

YCompressor contactor (stage 1)

C 24VACcommon[3]

O/B Changeover valve[7]

G Fan relay

Y2 Compressor contactor (stage 2)

LSends output when set to Em. Heat [11]

3H/2C Heat

Pump System

(TH6320U only) [10]

Rc Power [1]

R [R+Rc joined by jumper]

YCompressor contactor (stage 1)

C 24VACcommon[3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

LSends output when set to Em. Heat [11]

See [notes] on page 4.

MCR29448

RcY

RcYGAux

MCR29450

RcYGY2

MCR29451

RcYGAux

CY2

MCR29452

RcY

GAux

MCR29449A

Installation Guide

69-2695EFS— 01 6

ENGLISH

Done Next

MCR29454

Tobegin,press and hold the sand FAN

buttons until the display changes.

Function

number Setting

Press s or t to change settings.

Press NEXT to advance to the next function.

PressDONEtoexitandsavesettings.

Installer setup

Follow the procedure below to configure the thermostat to match the installed heat-

ing/coolingsystem,andcustomizefeatureoperationasdesired.

Continued on next page

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

*[Othercyclerateoptions:2,4,6,7,8,10,11or12CPH]

1System type 0 1 heat/1 cool conventional

1 1 heat/1 cool heat pump (no aux. heat)

2 Heatonly—2-wiresystems,3-wirezonevalves(Series20),andnor-

mally open zone valves

3 Heatonlywithfan

4 Cool only

5 2 heat/1 cool heat pump (with aux. heat)

6 2 heat/2 cool conventional

7 2heat/1coolconventional

8 1 heat/2 cool conventional

9 2 heat/2 cool heat pump (no aux. heat) - TH6320U only

10 3heat/2coolheatpump(withaux.heat)-TH6320U only

2Changeover valve

(O/B terminal) 0 Changeover valve (O/B terminal energized in cooling)

1 Changeover valve (O/B terminal energized in heating)

3Fan control

(heating) 0 Gas or oil furnace — equipment controls fan in heating

1 Electricfurnace—thermostatcontrolsfaninheating

5Stage 1 heat cycle

rate (CPH: cycles/

hour)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 Forhotwatersystems&furnaces of over 90% efficiency

9 For electric furnaces

6Stage 2 heat cycle

rate/Auxiliary heat

cycle rate (CPH)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 Forhotwatersystems&furnaces of over 90% efficiency

9 For electric furnaces

7Auxiliary heat cycle

rate (CPH)*

Only

TH6320U

for 3H/2C Heat Pumps

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 Forhotwatersystems&furnaces of over 90% efficiency

9 For electric furnaces

9Stage 1 compressor

cycle rate (CPH) 3 Recommended for most compressors

[Othercyclerateoptions:1,2,4,5or6CPH]

FocusPRO®TH6000 Series

7 69-2695EFS— 01

ENGLISH

Installer setup

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

10 Stage 2 compressor

cycle rate (CPH) 3 Recommended for most compressors

[Othercyclerateoptions:1,2,4,5or6CPH]

12 Manual/Auto

changeover 0 Manual changeover (Heat/Cool/Off)

1 Auto changeover (Heat/Cool/Auto/Off) **See page 8

2 Auto changeover only (Auto) **See page 8

13 Adaptive Intelligent

Recovery™1 On**See page 8

0 Off

14 Temperature

display 0 Fahrenheit

1 Celsius

15 Compressor

protection 5 Five-minute compressor off time **See page 8

[Otheroptions:0,1,2,3or4-minuteofftime]

16 Schedule format 0 5/2 (programmable weekdays and weekends)

1 5/1/1(weekdays,Saturday&Sundayprogrammable)

27 Heat temperature

range stops 90 Max. heat temperature setting is 90° F (32° C)

[Other options: 40 °F to 89 °F (4.5 °Cto31.5°C)]

28 Cool temperature

range stops 50 Min. cool temperature setting is 50° F (10° C)

[Other options: 51 °F to 99 °F (10.5 °Cto37°C)]

Installer system test

10 0

MCR29455

System test System status

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

Press s / t to turn system on/off.

Press NEXT to advance to next test.

PressDONEtoterminatesystemtest.

Test number System status

Tobegin,press and hold the s and t

buttons until the display changes.

10 Heating system 0 Heat and fan turn off.

1 Stage1heatturnson.FanturnsonifSetupFunction1issetto1,5,

9or10ORSetupFunction3issetto1**Seepage6

2 Stage 2 heat turns on

3 Stage3heatturnson-TH6320U only

20 Emergency heating

system 0 Heat and fan turn off

1 Heat and fan turn on

30 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Stage 2 compressor turns on

40 Fan system 0 Fan turns off

1 Fan turns on

CAUTION: Compressor protection is bypassed during testing. To prevent equipment

damage,avoidcyclingthecompressorquickly.

Installation Guide

Honeywell International Inc.

1985DouglasDriveNorth

GoldenValley,MN55422

http://customer.honeywell.com

Automation and Control Solutions

® U.S. Registered Trademark

69-2695EFS—01M.S.01-12

Printed in U.S.A.

Special functions

Auto Changeover(SetupFunction12):WhensettoAuto,thethermostatautomaticallyselects

heating or cooling depending on the indoor temperature. The thermostat will automatically adjust

heatandcoolsettingstomaintaina3-degreeseparation(fixed).Note:IfyouselectAuto Changeover

Only,theSystemSettingonthethermostatwillstaylockedintheAutoposition,preventingtheuser

fromchangingittoEmHeat,Heat,CoolorOff.

Adaptive Intelligent Recovery™(SetupFunction13):Allowsthethermostatto“learn”

howlongthefurnaceandairconditionertaketoreachprogrammedtemperaturesettings,sothe

temperature is reached at the scheduled time.

Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes

beforerestarting,topreventdamage.Duringthewaittime,themessageCoolOnorHeatOn(heat

pumps only) will flash on the display.

Accessories & replacement parts

Please contact your distributor to order replacement parts.

Battery holder ............................PartNumber50007072-001

Cover plate assembly* .....................PartNumber50002883-001

12 pack of medium cover plates* .............PartNumber50007298-001

*Use to cover marks left by old thermostats.

Specifications

Temperature Ranges

• Heat:40°to90°F(4.5°to32°C)

• Cool:50°to99°F(10°to37°C)

Operating Ambient

Temperature

• 32°to120°F(0°to48.9°C)

Shipping Temperature

• -20°to120°F(-28.9°to48.9°C)

Operating Relative Humidity

• 5%to90%(non-condensing)

Physical Dimensions

• 3-9/16"Hx5-13/16"Wx1-1/2"D

 91mmHx147mmWx38mmD

Electrical Ratings

Terminal Voltage(50/60Hz) RunningCurrent

WHeating 20-30Vac 0.02-1.0A

(Powerpile) 750mVDC 100mADC

W2(Aux/E)Heating 20-30Vac 0.02-1.0A

YCooling 20-30Vac 0.02-1.0A

Y2Cooling 20-30Vac 0.02-1.0A

GFan 20-30Vac 0.02-0.5A

O/BChangeover 20-30Vac 0.02-0.5A

LOutput 20-30Vac 0.02-0.5A

FocusPRO®Série TH6000

Thermostat programmable

® Marque de commerce déposée aux É.-U

Guide

d’installation

Doit être installé par un technicien expérimenté et qualifié.

Lire attentivement ces instructions. Le manquement à suivre ces instructions peut

entraîner des dommages au produit et causer des conditions dangereuses.

Besoin d’aide?

Pourobtenirdel’assistanceausujetdeceproduit,

consulter le http://customer.honeywell.com ou téléphoner sans frais

au Centre de service à la clientèle de Honeywell au 1 800 468-1502

Ce guide couvre les modèles suivants :

• TH6110D:Pour1systèmedechauffageet1systèmedeclimatisation

• TH6220D:Pour2systèmesdechauffageet2systèmesdeclimatisation

• TH6320U:Pour3systèmesdechauffageet2systèmesdeclimatisation

(Enlever le porte-piles pour trouver le numéro de modèle.)

Types de système

• Chauffageaugaznaturel,

au mazout ou à l’électricité

avec climatiseur

• Fournaisesàgrandrendement

à air chaud ou à eau chaude ;

thermopompes,systèmes

à la vapeur ou gravitaires

• Chauffageseulement–systèmes

àdeuxfils,soupapesdezone

à trois fils (Série 20) soupapes

de zones normalement ouvertes

• Chauffageseulementavec

soufflante

• Climatisationseulement

• Systèmesdechauffagede750mV

Guide d’installation

69-2695EFS— 01 2

FRANÇAIS

MCR29435

M29433

MCR29434

Installation de la plaque murale

1. Séparer la plaque murale du thermostat.

2. Installer la plaque murale tel que décrit

ci-dessous.

Percerdestrousde5mm(3/16po)

dans le placoplâtre.

Ancrages muraux

Plaque murale

Trou du fil Visdemontage

MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE

Peut causer un choc électrique ou endommager l’équipement. Couper l’alimentation avant

de commencer l’installation.

REMARQUE À PROPOS DU MERCURE :

Si ce produit sert à remplacer une commande qui contient du mercure dans un tube

scellé,nepasjeterlavieillecommandeauxordures.Consulterl’administration

locale de gestion des déchets pour connaître les instructions relatives au recyclage

et à l’élimination.

Tirer ici pour enlever la plaque

murale du thermostat neuf.

Retirer le porte-piles. Insérer la carte de référence

après avoir installé la plaque murale

(voir les instructions ci-dessous).

Il est plus facile de saisir la

plaque murale et de l’enlever

après avoir complètement

retiré le porte-pile.

Percerdestrousde5,5mm

(7/32po)silemurestenplâtre.

Andere Handbücher für FocusPRO Wi-Fi TH6000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T8095A Bedienungsanleitung

Honeywell

Honeywell Super Tradeline T874R Bedienungsanleitung

Honeywell

Honeywell T8602D Bedienungsanleitung

Honeywell

Honeywell T6R-HW Bedienungsanleitung

Honeywell

Honeywell CT2800 Technische Daten

Honeywell

Honeywell LYRIC T4 Bedienungsanleitung

Honeywell

Honeywell T8600D Bedienungsanleitung

Honeywell

Honeywell VisionPRO TB8220 Bedienungsanleitung

Honeywell

Honeywell RTHL2410 series Bedienungsanleitung

Honeywell

Honeywell T8611G Chronotherm IV Deluxe Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Bedienungsanleitung

Honeywell

Honeywell T3 Bedienungsanleitung

Honeywell

Honeywell T8132C Bedienungsanleitung

Honeywell

Honeywell CT3200 series Benutzerhandbuch

Honeywell

Honeywell Lyric T6R Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Series Bedienungsanleitung

Honeywell

Honeywell TL8230A Bedienungsanleitung

Honeywell

Honeywell RTH1100 series Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell PRO TH3210D Bedienungsanleitung

Honeywell

Honeywell T834H Bedienungsanleitung

Honeywell

Honeywell T410A Bedienungsanleitung

Honeywell

Honeywell TH2210DV Bedienungsanleitung

Honeywell

Honeywell Prestige Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung