Honeywell PRO TH4110B Bedienungsanleitung

Installation

Guide

TH4110B

Programmable Thermostat

Product Application

This thermostat provides electronic control of 24 VAC single-stage heating and cool-

ing systems, or 750 mV heating systems.

System Types

• Gas, oil, or electric heat with air

conditioning

• Warm air, hot water, high-efficiency

furnaces, heat pumps, steam, gravity

• Heat only

• Heat only with fan

• Cool only

• 750 mV heating systems

Power Type

• AA alkaline batteries (2)

System Settings

• Heat, Off, Cool

Fan Settings

• Auto, On

Must be installed by a trained, experienced technician

• Read these instructions carefully. Failure to follow these instructions can dam-

age the product or cause a hazardous condition.

• Check the ratings in this booklet to verify that this product is suitable for your

application (see page 12).

• Always test for proper operation after installation (see pages 8-9).

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

® U.S. Registered Trademark. Patents pending.

PRO TH4110B Programmable Thermostat

Install the thermostat about 5 feet (1.5m) above the floor in an area

with good air circulation at average temperature.

Do not install in locations where the thermostat can be affected by:

• Drafts or dead spots behind doors and in corners

• Hot or cold air from ducts

• Sunlight or radiant heat from appliances

• Concealed pipes or chimneys

• Unheated/uncooled areas such as an outside wall behind the thermostat

NO NO

IInnssttaallllaattiioonn

Pre-installation checklist ................2

Wallplate installation ......................3

Wiring..............................................4

Wiring diagrams ..............................5

IInnssttaalllleerrSSeettuupp

Fan operation settings ....................6

Battery installation ..........................7

Thermostat mounting ....................7

Installer setup..................................8

Installer system test ........................9

AAppppeennddiicceess

Quick reference to controls..........10

Quick reference to display............10

Compressor protection ................10

In case of difficulty ......................11

Accessories....................................12

Specifications ................................12

Table of contents

Installation tips

Installation Guide

Pre-installation checklist

Package contents

Check to make sure your package includes the following items:

Operating manual

Wall anchors and

mounting screws

(2 each)

AA alkaline

batteries (2)

Quick reference card

PRO TH4110B

digital thermostat

(wallplate attached to back)

Required tools & supplies

• No. 2 Phillips screwdriver

• Small pocket screwdriver

• Drill

• Drill bit (3/16” for drywall, 7/32” for plaster)

• Hammer

• Pencil

• Electrical tape

• Level (optional)

PRO TH4110B Programmable Thermostat

Remove the wallplate from the ther-

mostat as shown at left, then follow

directions below for mounting.

1 Pull wires through wire hole.

2 Position wallplate on wall, level and

mark hole positions with pencil.

3 Drill holes at marked positions as

shown below, then tap in supplied

wall anchors.

4 Place wallplate over anchors, insert

and tighten mounting screws.

5 Insert quick reference card in slot

in front of wall plate.

Grasp top and bottom of wallplate

and pull to remove from thermostat.

Drill 3/16” holes for drywall.

Drill 7/32” holes for plaster.

Wall anchors

Mounting screwsWire hole

Wallplate installation

Insert quick reference card after

wallplate is mounted (see mounting

instructions, below)

Installation Guide

Wiring

1 Loosen screw terminals, insert

wires into terminal block, then

re-tighten screws.

2 Push excess wire back into the

wall opening. Keep wires in shaded

area as shown at left.

3 Plug the wall opening with non-

flammable insulation to prevent

drafts from affecting thermostat

operation.

Terminal Designations

WWHeat relay.

YYCompressor contactor.

GGFan relay.

OOHeat pump changeover valve

energized in cooling.

RRccCooling power. Connect to

secondary side of cooling

system transformer.

RRHeating power. Connect to

secondary side of heating

system transformer.

BBHeat pump changeover valve

energized in heating.

Terminal

block

NOTES

R & Rc terminals

In single-transformer system, leave metal

jumper in place between R & Rc. Remove

metal jumper if two-transformer system.

Heat pump systems

If wiring to a heat pump, use a small piece of

wire (not supplied) to connect terminals W

and Y.

Wire specifications

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

Keep wires in this

shaded area

CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage.

Disconnect power before wiring.

Wiring

Jumper

PRO TH4110B Programmable Thermostat

Typical 1H/1C system: 1 transformer Typical 1H/1C system: 2 transformers

Power supply. Provide disconnect means and overload protection as required.

Factory-installed jumper. Remove for 2-transformer systems only.

Use either Oor Bterminals for changeover valve.

Use a small piece of wire (not supplied) to connect Wand Yterminals.

Set fan operation switch to Heat Pump (see page 6) and configure for heat pump (see pg. 8).

Remove jumper

Wiring diagrams

Typical 1H/1C heat pump system Typical heat-only system

Typical heat-only system with fan Typical cool-only system

Installation Guide

•GGaassoorrOOiill::For gas or oil heating

systems, leave the fan operation

switch in this factory-set position

(This setting is for systems that

control the fan in a call for heat.)

•EElleeccttrriiccoorrHHeeaattPPuummpp::Change the

switch to this setting for heat

pump or electric heat systems.

(This setting is for systems that

allow the thermostat to control the

fan in a call for heat, if a fan wire is

connected to the GGterminal.)

Set fan operation switch

Fan operation settings

PRO TH4110B Programmable Thermostat

Install batteries in back of thermostat

Install two AA alkaline batteries in the

back of the thermostat, as shown at

left.

Fresh batteries should be installed

immediately when the RREEPPLLAACCEEBBAATTTT

warning begins flashing (see page 10.)

The warning flashes about two months

before batteries are depleted.

Even if the warning does not appear,

Batteries should be replaced once a year,

or before the home is left vacant for

more than a month.

Battery installation

Align the 4 tabs on the wallplate with

corresponding slots on the back of the

thermostat, then push gently until the

thermostat snaps in place.

Thermostat mounting

Setup

Installation Guide

System type

Heating cycle rate

(CPH: cycles/hour)

Compressor

cycle rate (CPH)

Temperature

display

Compressor

protection

0 Gas, oil or electric heat with air conditioning

1 Heat pump (5 minute compressor off time in heating and cooling)

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

0 Fahrenheit

1 Celsius

5 Five-minute compressor off time **See page 10

[Other options: 0, 1, 2, 3 or 4-minute off time]

Setup Function Settings & Options

To begin, press and hold the and

buttons until the display changes

Function number

Press to change settings

Press to advance to next function

Press and hold to exit and save settings

Setting

Installer setup

Follow the procedure below to configure the thermostat to match the installed

heating/cooling system, and customize feature operation as desired.

Installer system test

After completing the installer setup above, press the button again to begin a

system test (see next page).

Press and hold both buttons

Andere Handbücher für PRO TH4110B

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell Lyric T5 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell MagicStat T8132 Bedienungsanleitung

Honeywell

Honeywell Tradeline T874A-F Bedienungsanleitung

Honeywell

Honeywell ZonePro Bedienungsanleitung

Honeywell

Honeywell FEMA TAM Series Bedienungsanleitung

Honeywell

Honeywell THX9000 Prestige HD Benutzerhandbuch

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell RTH1100 series Bedienungsanleitung

Honeywell

Honeywell T6 Pro Z-Wave Bedienungsanleitung

Honeywell

Honeywell RTH6500 Bedienungsanleitung

Honeywell

Honeywell RTHL2310 series Bedienungsanleitung

Honeywell

Honeywell Chronotherm IV T8611G Bedienungsanleitung

Honeywell

Honeywell T7351F2010 - Digital Thermostat, 3h Bedienungsanleitung

Honeywell

Honeywell Round T8700C Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4500 Bedienungsanleitung

Honeywell

Honeywell Magic Stat MS3000 Bedienungsanleitung

Honeywell

Honeywell T8132A Bedienungsanleitung

Honeywell

Honeywell RedLINK Bedienungsanleitung

Honeywell

Honeywell T841A Bedienungsanleitung

Honeywell

Honeywell CM707 Bedienungsanleitung

Honeywell

Honeywell TL5110 Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5220D Bedienungsanleitung

Honeywell

Honeywell Chronotherm III Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung