HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

installation

instructions

hp StorageWorks

SAN switch

rack mount kit

Second Edition (June 2003)

Part Number: AV–RU6YB–TE

This document provides step-by-step instructions for installing the SAN Switch 2/8, SAN Switch

2/16 or SAN Switch 2/32 using the hp StorageWorks SAN switch rack mount kit.

For the latest version of these Installation Instructions and other documentation, access the HP

storage website at:

http://www.hp.com/country/us/eng/prodserv/storage.html

2 SAN Switch Rack Mount Kit Installation Instructions

Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for

errors contained herein or for incidental or consequential damages in connection with the furnishing, performance,

or use of this material.

This document contains proprietary information, which is protected by copyright. No part of this document may be

photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard.

The information contained in this document is subject to change without notice.

BROCADE, the Brocade B weave logo, Brocade: the Intelligent Platform for Networking Storage, SilkWorm, and

SilkWorm Express, are trademarks or registered trademarks of Brocade Communications Systems, Inc. or its

subsidiaries in the United States and/or in other countries.

Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The

information is provided “as is” without warranty of any kind and is subject to change without notice. The warranties

for Hewlett-Packard Company products are set forth in the express limited warranty statements for such products.

Nothing herein should be construed as constituting an additional warranty.

Printed in the U.S.A.

SAN Switch Rack Mount Kit Installation Instructions

Second Edition (June 2003)

Part Number: AV–RU6YB–TE

3SAN Switch Rack Mount Kit Installation Instructions

About this Document

This document describes the installation of the SAN Switch 2/32, SAN Switch

2/16, and SAN Switch 2/8 in an HP Series 9000 or comparable EIA rack, or in an

HP System/e rack using the SAN Switch Rack Mount Kit, part number

331148-B21.

This section describes the content reflected in this document, including:

■Intended Audience, page 3

■Related Documentation, page 3

■Rack Stability, page 4

■Installation and Safety Guidelines, page 5

■Installing the Switch in a Rack Using the SAN Switch Rack Mount Kit,

page 8

Intended Audience

This book is intended for use by system administrators who are experienced with

the following:

■HP StorageWorks Fibre Channel SAN switches

■Fabric Operating System (FOS) V3.1.x or later

Related Documentation

For a list of related documents included with this product, see the Related

Documents section of the Release Notes that came with your switch.

For the latest information, documentation, and firmware releases, please visit the

following StorageWorks website:

http://www.hp.com/country/us/eng/

prodserv/storage.html

For information about Fibre Channel standards, visit the Fibre Channel

Association website, located at:

http://www.fibrechannel.org

4 SAN Switch Rack Mount Kit Installation Instructions

Rack Stability

Rack stability protects personnel and equipment.

WARNING: To reduce the risk of personal injury or damage to the

equipment, be sure that:

■The leveling jacks are extended to the floor.

■The full weight of the rack rests on the leveling jacks.

■In single rack installations, the stabilizing feet are attached to the rack.

■In multiple rack installations, the racks are coupled.

■Only one rack component is extended at any time. A rack may become

unstable if more than one rack component is extended for any reason.

5SAN Switch Rack Mount Kit Installation Instructions

Installation and Safety Guidelines

Read the following sections for installation guidelines. Install the SAN Switch in

one of the following ways:

■As a stand-alone unit on a flat surface.

■In an Electronics Industries Association (EIA) cabinet (like the HP 9000

Series Rack).

■In an HP System/e rack.

Selecting an Operating Location

To ensure correct operation of the switch, the location where the switch is in use

must meet the following requirements:

■Adequate supply circuit, line fusing, and wire size, as specified by the

electrical rating on the switch nameplate.

■An air flow of at least 300 cubic feet per minute, available in the immediate

vicinity of the switch.

■If installing the switch in the HP 9000 Series, or comparable EIA rack:

— All equipment installed in the rack should have a reliable branch circuit

ground connection, and should not rely on a connection to a branch

circuit, such as a power strip.

— The rack should be balanced and the installed equipment should be within

the rack’s weight limits. Ensure the rack is mechanically secured to insure

stability in the event of an earthquake.

Cooling Requirements

Cooling air is drawn into the switch chassis by the fans mounted on the rear of the

chassis. The air is expelled through vents in the front (port side) of the chassis,

next to the HP logo. HP recommends installing the switch so that air intake and

exhaust for all components in the rack is flowing in the same front-to-back

direction.

Note: HP highly recommends mounting the switch in a cabinet or rack so that the fans

reside in the front of the cabinet, and the ports (cables) reside in the rear of the cabinet.

6 SAN Switch Rack Mount Kit Installation Instructions

Follow these guidelines to ensure proper air flow, and prevent component

overheating:

■To ensure adequate cooling, install the switch with the non-port side,

which contains the air intake vents, facing the cool-air aisle.

■Verify a minimum of 47 cubic feet/minute (79.8 cubic meters/hour) of air

flow is available to the air intake vents on the non-port side of the switch.

■Verify that the ambient air temperature does not exceed 40° Celsius (104°

Fahrenheit) while the switch is operating.

Caution: Do not block air vents. The switch uses ambient air for cooling.

Power Requirements

The AC power source must meet these requirements:

■Primary AC Input 100–240 VAC (switch auto-senses input voltage) 47–63 Hz

■Correctly wired primary outlet, with circuit protected by a circuit breaker and

grounded in accordance with local electrical codes

■Adequate supply circuit, line fusing, and wire size, as specified by the

electrical rating on the switch nameplate

■Voltage capability of 85–264 VAC

■Input voltage frequency of 47–63 Hz

■Power capability of 75 W maximum

Rack Mount Checklist

Verify that the rack and the area around the rack meets the following

requirements:

■The cabinet must be a standard EIA cabinet.

■Plan a cabinet space that is 1.5 rack units high (2.6 inches; 6.7 cm), 19 inches

(48.3 cm) wide, and at least 23 inches (68.6 cm) deep.

■Ground all equipment in the cabinet through a reliable branch circuit

connection, and maintain ground at all times. Do not rely on a secondary

connection to a branch circuit, such as a power strip.

7SAN Switch Rack Mount Kit Installation Instructions

■Ensure that air flow and temperature requirements are met on an ongoing

basis, particularly if the switch is installed in a closed or multi-rack assembly.

■Verify that the additional weight of the switch does not exceed the cabinet’s

weight limits or unbalance the cabinet in any way.

■Secure the cabinet to insure stability in case of unexpected movement.

Note: For proper air flow, the SFP media side of the switch must face the rear of the

rack. This mounting allows air to enter from the front of the rack and to exhaust at the

rear of the rack, similar to other rack-mounted equipment. This prevents switch

overheating.

8 SAN Switch Rack Mount Kit Installation Instructions

Installing the Switch in a Rack Using the SAN Switch

Rack Mount Kit

This section provides instructions for installing the SAN Switch 2/32, SAN

Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series

or comparable EIA rack using the SAN Switch Rack Mount Kit, part number

331148-B21.

Figure 1: SAN Switch 2/16 rack-mounted switch

Note: The Rack Mount Kit installation requires one technician to install a SAN switch.

The following items are required to install the switch in a rack:

■SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8

■Power cables

■#2 Phillips screwdriver

■7/16-inch wrench or socket

■The SAN Switch Rack Mount Kit rails and rail mounting hardware listed

9SAN Switch Rack Mount Kit Installation Instructions

(2) rear mounting brackets

A right inner rail and a right outer rail

A left inner rail and a left outer rail

(14) #8-32 x 3/16-inch Phillips pan-head

screw with thread lock

(10) #10-32 x 1/2-inch Phillips pan-head

screw with captive star lock washer

(8) #10 alignment washer

(8) #10 adapter washer

(2) 1/4-20 hex nut with captive star lock

washer

(2) 1/4-inch flat washer

10 SAN Switch Rack Mount Kit Installation Instructions

Caution: For proper air flow, the SFP media side of the SAN Switch 2/32,

SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This

mounting allows air to enter from the front of the rack and to exhaust at the

rear of the rack, similar to other rack-mounted equipment. This prevents switch

overheating, which may cause it to fail.

To install the switch in a rack:

1. Check contents of the shipping carton to verify all the required parts and

hardware are available.

2. Choose a mounting location in the rack for the switch.

3. Attach the rear mounting brackets to the rear rack uprights by completing one

of the following steps:

— For an HP 9000 Series or comparable EIA rack, assemble each of the two

brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and (2) #10 adapter washers as shown in Figure 2.

Figure 2: Installing the rear mounting brackets (HP 9000 Series or comparable EIA

rack)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP Dual Hinge Notebook Stand Technisches Datenblatt

HP E1586A Bedienungsanleitung

HP A4838A Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Bedienungsanleitung

HP Proliant DL580 Bedienungsanleitung

HP cc2300 Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP 6400/8400 Bedienungsanleitung

HP MCS 5042 Bedienungsanleitung

HP Tc4100 - Server - 256 MB RAM Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Gebrauchsanweisung

HP DESKJET 350 Bedienungsanleitung

HP StorageWorks SSL1016 Bedienungsanleitung

HP RP9 Compact Stand Bedienungsanleitung

HP Rack System/E Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP 669048-009 Bedienungsanleitung

HP Model 745 - VME Workstation Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Quick Release EM870AA Gebrauchsanweisung

HP D7171A - NetServer - LPr Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung