HP Proliant DL580 Bedienungsanleitung

HP 3-7U Quick Deploy

Rail System

Installation Instructions

for HP products

The information contained herein is subject to change without notice. The only

warranties for HP products and services are set forth in the express warranty

statements accompanying such products and services. Nothing herein should

be construed as constituting an additional warranty. HP shall not be liable for

technical or editorial errors or omissions contained herein.

June 2006 (Third Edition)

Part Number 378950-003

Overview

This rack hardware kit supports a variety of 3-7U HP products

in round-, square-, or threaded-hole racks. Use the legend to

identify installation steps appropriate to the type of rack.

IMPORTANT: If you are shipping the server installed

in a rack, see the additional instructions located in

"Preparing the product for rack relocation or

integrated shipping" before proceeding.

Hardware kit contents

In addition to the supplied items, you may need:

•Screws that fit a threaded-hole rack

•The appropriate screwdriver for the screws

•Kit 371482-B21 for integrated shipping a

round-hole rack

Rack warnings

WARNING: To reduce the risk of personal

injury or damage to the equipment,

be sure that:

•The leveling jacks are extended to

the floor.

•The full weight of the rack rests on the

leveling jacks.

•The stabilizing feet are attached to the

rack if it is a single-rack installation.

•The racks are coupled together in

multiple-rack installations.

•Only one component is extended at a

time. A rack may become unstable if

more than one component is extended

for any reason.

Anti-tip stabilizer

The anti-tip stabilizers provide stability and support when

equipment is installed, removed or accessed within the rack.

Stabilizer kits are available in both 600-mm and 800-mm

versions. HP also recommends using the side feet, provided

with these kits, to stabilize stand-alone racks from the other

side. If you are stabilizing racks that are secured together

with baying kits, the side feet are optional on either end

of the row.

HP recommends that stabilizer option kits be used when one

or more of the following situations occur:

•The standard 600-mm (23.62-in) or 800-mm (31.50-in)

front foot is required with deployments of

stand-alone racks.

•Side feet, which are included in the stabilizer kits, are

recommended to be installed as well.

Rack rows with four or more bayed racks, without a single

rack-mountable components exceeding 99.79 kg (220 lb), do

not need a stabilizer kit installed.

Lift

WARNING: If you are going to use a lift, be

sure to use a lift that can handle the load of

the server.

Installing the product in a rack

CAUTION: Always plan the rack installation so that

the heaviest item is on the bottom of the rack. Install

the heaviest item first, and continue to populate the

rack from the bottom to the top.

IMPORTANT: If you are shipping the server installed

in a rack, see the additional instructions located in

"Preparing the product for rack relocation or

integrated shipping" before proceeding.

IMPORTANT: If you are installing the server in a

shallow rack [i.e., less than 72.39 cm (28.5 in)], see

the additional instructions located in "Preparing the

rails for shallow rack installation" before proceeding.

WARNING: To reduce the risk of personal

injury or equipment damage, be sure that

the rack is adequately stabilized before

sliding the server into the rails.

WARNING: To reduce the risk of personal

injury or equipment damage, do one of

the following:

•Use two or more people to lift and

stabilize the product pieces

during assembly.

•Use a lift that can handle the load

of the product.

CAUTION: Be sure to keep the product parallel to

the floor when sliding the server into the rails.

Tilting the product up or down could result in

damage to the slides.

Installing the cable

management arm

IMPORTANT: If you need to hinge the cable

management arm on the rear right-hand side of the

rack, see the instructions located in "Converting the

cable management arm swing" and perform the steps

to convert the arm to a right-hand swing before

installing the arm on the rack. After conversion,

mirror the installation steps on the rear right-hand

side of the rack.

NOTE: When properly installed, the cable

management arm is attached to the server and the

rack rail.

The installation is complete.

If the rack installation is to be shipped with product(s)

installed, perform the steps in "Preparing the product for rack

relocation or integrated shipping."

Converting the cable

management arm swing

The cable management arm is designed for ambidextrous

implementation. You can convert the arm for

right-hand swing.

NOTE: To access some components on the rear of the

product, you may need to remove the cable

management arm.

IMPORTANT: When converting the cable arm,

always be sure to orient the arm with the cable trough

facing upward.

The cable management arm is ready for installation on

the rack.

Preparing the rails for

integrated shipping in a rack

IMPORTANT: You must provide screws to secure

the slide mounting bracket assemblies in a

threaded-hole rack.

IMPORTANT: You will need kit 371482-B21 to

prepare a round-hole rack for integrated shipping.

NOTE: Use the integrated shipping hardware

included with this kit to prepare a square-hole rack for

integrated shipping.

Return to step 1 in "Installing the product in a rack."

Preparing the product for

rack relocation or

integrated shipping

To service or remove the product from the rack, reverse the

procedures in this section:

1. Remove the rear slide locking screw and the front rail

locking screws. Retain the screws for future use.

2. Cut and discard the orange tie wraps.

Preparing the rails for shallow

rack installation

Return to step 2 in "Installing the product in a rack."

Andere Handbücher für Proliant DL580

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

HP Rack System/E Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Gebrauchsanweisung

HP StorageWorks SSL1016 Bedienungsanleitung

HP 6400/8400 Bedienungsanleitung

HP Location Discovery Services Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP Integrated Work Center Stand Gebrauchsanweisung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP Retail Mobile POS Case Bedienungsanleitung

HP 355 Bedienungsanleitung

HP J1530C Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP DL320s - ProLiant 9TB SATA Storage Server... Bedienungsanleitung

HP Quick Release EM870AA Gebrauchsanweisung

HP Z600 - Workstation - 6 GB RAM Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Bedienungsanleitung

HP TFT7600 G2 Bedienungsanleitung

HP E1586A Bedienungsanleitung

HP Model 745 - VME Workstation Bedienungsanleitung

HP ProCurve 6600-48G-4XG Bedienungsanleitung

HP Tc4100 - Server - 256 MB RAM Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung