HP Z600 - Workstation - 6 GB RAM Bedienungsanleitung

Sliding rack-mount kit installation

Introduction

This document describes how to install the sliding rack mount kit on an HP Z600 Workstation and an

HP Z800 Workstation. It also describes how to install the workstation into a rack.

For Legacy Rack Customers:

Owners of earlier model racks (E3660B, E3661B, E3662B, E7590A, J1450B or J1487A/B) must also

purchase the HP Legacy Rack Adapter, part number WD587AA, to install the sliding rack mount kit.

Kit contents

This product includes the parts needed to install the sliding rack kit in HP round hole and square hole

racks, earlier HP racks, and some third-party racks, including some racks with threaded holes. The

following list describes all of the included parts; however, not all parts are used with every application.

A. Outer slide assembly (2) B. Inner slide assembly (2) C. Flange (2) D. M4 screw (8)

Earlier HP racks and third party racks

Parts for installing the sliding rack mount in HP legacy racks are sold separately in adapter kit part

number WD587AA. This adapter kit includes these parts:

AA. Front bracket (2) BB. M5 screw (4) CC. M6 screw (2) DD. Adapter bracket (2)

(Required for earlier HP racks

only.)

ENWW Introduction 1

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed

area marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce

the risk of injury from a hot component, enable the surface to cool before touching.

WARNING! If a product is shipped in packaging marked with this symbol, , the product must always

be lifted by two persons to avoid personal injury due to product weight.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper

workstation setup, posture, health, and work habits for computer users, and provides important electrical

and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the

documentation CD (if one is included with the product).

CAUTION: Static electricity can damage the electronic components of the workstation. Before

beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal

object.

CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge

(ESD) precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body

to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat,

static strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested

for reliability and are manufactured to high quality standards.

2 Sliding rack-mount kit installation ENWW

Tools required

Round hole and square hole racks

●T-15 Torx screwdriver

Threaded hole racks

●T-15 Torx screwdriver

●Flat head screwdriver

●Cross-tip screwdriver

For earlier HP racks including E3660B, E3661B, E3662B, J1450B, J1487A,

J1487B

●T-15 Torx screwdriver

●T-25 Torx screwdriver

●M10 socket wrench

Step 1—Preparing the workstation

NOTE: All illustrations are examples only. Workstation models vary. For product-specific information,

see the service guide for your HP workstation at http://www.hp.com/support/workstation_manuals

before beginning installation.

To prepare the workstation for component installation:

1. Power down the workstation and all external devices.

2. Disconnect the workstation power cord.

3. Disconnect all connections to external devices.

4. Remove the side access panel.

ENWW Tools required 3

5. Remove the rear handle by using a T-15 Torx screwdriver to remove the long screw that secures

the handle (1), and then remove the handle (2).

Figure 1 Removing the rear handle

6. Lift the rear edge of the top cover at the center detente (1), press on the front edge of the top cover

(2), and then slide the cover toward the rear of the system.

Figure 2 Disengaging the top cover

4 Sliding rack-mount kit installation ENWW

7. Lift the top cover from the chassis as shown in the following figure.

Figure 3 Removing the top cover

8. Reinstall the side access panel.

Step 2—Installing rails and flanges

1. Align the flange with the screw holes on the left side of the chassis (the bottom of chassis becomes

the left side for mounting) (1).

2. Attach the flange (2), using a T-15 Torx screwdriver and two M4 screws.

3. Align the inner slide with the two screw holes on the left side (the bottom) of the chassis (3).

NOTE: The front inner slide is stamped “FRONT.”

4. Attach the slide (4) using a T-15 Torx screw driver and two M4 screws.

5. Repeat steps 1–4 for the right side (the top) of the chassis.

Figure 4 Installing rails and flanges

ENWW Step 2—Installing rails and flanges 5

Step 3—Installing rails to the rack

(Optional) Adjusting slides to fit shallower or deeper third-party racks

1. Remove the slide adjustment attachment (1).

2. Adjust the rail to the desired length (2).

3. Insert the slide adjustment attachment (3).

Figure 5 Adjusting slides

6 Sliding rack-mount kit installation ENWW

Installing on round hole and square hole HP racks

These instructions apply to racks such as standard HP racks.

NOTE: To determine the appropriate alignment for a workstation that requires a 4U space (HP Z600

Workstations) or a 5U space (HP Z800 Workstations), see the two Figure 12 Mounting reference

guides on page 11.

1. Engage the three pins on the rear slide mounting bracket in the holes in the rear rack column, and

then slide forward to lock in place (1).

2. Engage the three pins on the front slide mounting bracket in the holes in the front rack column, and

then slide backward to lock in place (2).

NOTE: The slide telescopes to accomplish this task.

Repeat this procedure for the second slide.

3. If the slide must be repositioned, release the rear bracket (3).

4. If the slide must be repositioned, release the front bracket (4).

Figure 6 Installing on round and square hole HP racks

5. Continue with Step 4—Mounting into a rack on page 10.

ENWW Step 3—Installing rails to the rack 7

Installing on threaded hole racks

NOTE: To determine the appropriate alignment for a workstation that requires a 4U space (HP Z600

Workstations) or a 5U space (HP Z800 Workstations), see the two Figure 12 Mounting reference

guides on page 11.

1. Remove the three pins from the rear slide mounting bracket, using a flat blade screwdriver (1).

2. Remove the three pins and two nuts from the front slide mounting bracket (2).

3. Attach the rear slide mounting bracket to the rear rack column, using screws provided by the rack

manufacturer (3).

4. Attach the front slide mounting bracket to the front rack column using, screws provided by the rack

manufacturer (4).

5. Adjust the rear slide (5) if necessary.

Figure 7 Installing on threaded hole racks

6. Continue with Step 4—Mounting into a rack on page 10.

8 Sliding rack-mount kit installation ENWW

Installing on earlier HP racks

NOTE: The parts for this procedure are available separately in adapter kit number WD587AA.

1. Extend the rails (1).

2. Remove the rear mounting brackets from the outer slides (2).

3. Remove the front mounting brackets from the outer slides (3). Save the bracket nuts for use in

Steps 6 and 7.

Figure 8 Installing on earlier HP racks

4. Attach adapter bracket to the outer slides (4).

Figure 9 Attaching the adapter bracket to the outer slides

NOTE: To determine the appropriate alignment for a workstation which requires a 4U space

(Z600 Workstations) or a 5U space (HP Z800 Workstations), see Figure 12 Mounting reference

guides on page 11.

5. Attach the front bracket with two M5 screws (5).

6. Attach the slide to the inside rear of the rack, using an M6 flathead screw and one of the nuts

removed in Step 3 (6).

ENWW Step 3—Installing rails to the rack 9

7. Attach the slide to the front of the rack using the M6 screw mounted in the slide and the remaining

nut from Step 3 (7).

Figure 10 Attaching the brackets

Step 4—Mounting into a rack

WARNING! Two people are necessary to properly align and install the workstation and rails.

1. Insert the inner rails into the outer rails.

2. Push the workstation to slide it completely into the rack. If the rails are locked, disengage them by

pressing the green lever found on the side of the outer rail.

3. Secure the workstation into the rack by tightening the thumb screws found on the mounting flanges.

Figure 11 Mounting into a rack

10 Sliding rack-mount kit installation ENWW

Andere Handbücher für Z600 - Workstation - 6 GB RAM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP A4838A Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP StorageWorks SSL1016 Bedienungsanleitung

HP Intelligent Series Bedienungsanleitung

HP DL320s - ProLiant 9TB SATA Storage Server... Bedienungsanleitung

HP ML110 - ProLiant G5 2TB Storage Server NAS Bedienungsanleitung

HP Integrated Work Center Stand Gebrauchsanweisung

HP 11000 G2 series Bedienungsanleitung

HP Proliant DL580 Bedienungsanleitung

HP cc2300 Bedienungsanleitung

HP RP9 Compact Stand Bedienungsanleitung

HP 669048-009 Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Model 745 - VME Workstation Bedienungsanleitung

HP ProCurve 6600-48G-4XG Bedienungsanleitung

HP TFT7600 G2 Bedienungsanleitung

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Bedienungsanleitung

HP Dual Monitor Stand Technisches Datenblatt

HP Retail Mobile POS Case Bedienungsanleitung

HP MCS 5042 Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Quick Release EM870AA Gebrauchsanweisung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung