HP A4838A Bedienungsanleitung

HP 9000 D Class Enterprise Servers

A4838A Mounting Kit Guide

for HP A3764A and HP A3765A Cabinets

Part No. A3764-90003

Edition 1 - September 1997

E0997

Printed in: USA

Legal Notices

The information in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but

not limited to, the implied warranties of merchantability and ﬁtness for a particular

purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct,

indirect, special, incidental or consequential damages in connection with the furnishing,

performance, or use of this material.

Restricted Rights Legend. Use, duplication or disclosure by the U.S. Government is

subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical

Data and Computer Software clause at DFARS 252.227-7013 for DOD agencies, and

subparagraphs (c) (1) and (c) (2) of the Commercial Computer Software Restricted Rights

clause at FAR 52.227-19 for other agencies.

HEWLETT-PACKARD COMPANY 3000 Hanover Street Palo Alto, California 94304 U.S.A.

Reproduction, adaptation, or translation of this document without prior written

permission is prohibited, except as allowed under the copyright laws.

Preface-iii

Printing History

The manual printing date and part number indicate its current edition. The printing date

will change when a new edition is printed. Minor changes may be made at reprint without

changing the printing date.

Manual updates may be issued between editions to correct errors or document product

changes. To ensure that you receive the updated or new editions, you should subscribe to

the appropriate product support service. See your HP sales representative for details.

First Edition: ......................................................................... September, 1997

NOTE Reader Comments. We welcome your comments about our documentation.

If you have editorial suggestions or recommended improvements for this

document, please write to us. You can reach us through e-mail at:

hardwaredocs@cup.hp.com or by sending your letter to: Documentation

Manager M/S 5657, Hewlett-Packard Company, 8000 Foothills Blvd.,

Roseville, CA 95747-6588 USA. Please include the following information in

your message:

• Title of the manual you are referencing.

• Manual part number (from the title page).

• Edition number or publication date (from the title page).

• Your name.

• Your company’s name.

SERIOUS ERRORS, such as technical inaccuracies that may render a

program or a hardware device inoperative, should be reported to your HP

Response Center or directly to a Support Engineer.

Preface

This edition of the Mounting Kit Installation Guide contains technical information about

attaching the rack mount hardware to the D Class family of computers. The procedures in

this guide are intended for trained and experienced HP ﬁeld service personnel. At the time

of publication, this family of computers included the following models:

HP 9000 Model:

D2xx

D3xx

Preface-iv

Chapter 1 1-1

Introduction

A4838A Kit Contents

1Introduction

The HP 9000 D2xx and D3xx Enterprise Class of servers can be mounted into an A3764A

or A3765A cabinet to consolidate the pieces of the core system. The cabinet is offered as a

factory integrated cabinet (A3764A) with one to four D Class computers mounted, or a ﬁeld

integrated (A3765A) cabinet with no computers mounted by the factory. The cabinets have

mounting columns that comply with EIA standard 23 inch mounting ﬂanges.

The A4838A Mounting Kit contains the hardware that attaches to the D Class computer to

allow the computer to be mounted in the cabinet.

A4838A Kit Contents

If the shipment is incomplete or if the components are damaged or fails to meet

speciﬁcations, notify the nearest Hewlett-Packard Sales and Support Ofﬁce. If damage

occurred in transit, notify the carrier as well. Hewlett-Packard will arrange for

replacement or repair without waiting for settlement of claims against the carrier. If the

shipment was damaged in transit, keep the shipping containers and packaging material

for inspection.

When the shipment arrives, make sure the kit contains the following items.

• 5 ft. power cord (8120-1860)

• D Class Front Bezel (A3262-60021, see note)

• D Class Tray Carrier (A3764-00017)

• 6-32 #T15 TORX screws (5 each, 0624-0719)

• 10-32 #T25 TORX screws (4 each, 2680-0278)

NOTE The additional D Class Front Bezel (A3262-60021) is required if the D Class

computer being modiﬁed to install in the A3764A or A3765A cabinet is being

moved from a current 19 inch cabinet. If the D Class computer being modiﬁed

is a deskside type computer the additional bezel is not required.

Do not discard or destroy the shipping container or the packaging material. If it becomes

necessary to repackage the kit, these items will be needed.

1-2 Chapter1

Introduction

Required Tools

Before beginning the installation process, make sure you have the necessary tools.

• Standard hand tools.

• T10, T15, and T25 Torx driver.

D Class Mounting Procedures

Before starting any of the following procedures, be sure the D Class computer has been

recently backed up. Depending on the conﬁguration (deskside or 19 inch rack mount) of the

D Class computer, perform the appropriate procedure.

WARNING To avoid serious damage to the computer equipment and possible

injury, carefully read and follow all procedures in this guide.

D Class Deskside Computer Procedures

1. Turn the computer off.

2. Disconnect all cables from the computer. Be sure to record which cables were connected

to the computer in case they need to be re-connected once the computer is in the

cabinet.

3. Remove the Cosmetic Frame (upper or lower) from the cabinet, by removing the four

mounting screws and nylon washers.

4. Remove the cosmetic panel, covering the position of the computer to be mounted, from

the frame by removing the six plastic push pegs from the sides of the cosmetic panel.

5. Refer to Figure 1-1. Move the slide lockout (1) away from the installation position of the

cabinet. Fully extend the middle (2) and side rail (3) assemblies.

Chapter 1 1-3

Introduction

D Class Mounting Procedures

Figure 1-1 Carrier Tray Mounting Diagram

6. Align the tray carrier (4) over the extended rails so that the four mounting holes match

those in the rails and the alignment pins (5) on the rails match the tray. Insert the four

mounting screws (6) from the bottom of the rails, give the mounting screws a few turns,

but do not tighten at this time.

7. Remove the two screws from the computer chassis in the back, upper left or back, right

corner. Which corner depends on whether the computer is mounted on the right or left

side of the cabinet respectively. This is for the retainer bracket screws that secure the

computer into the cabinet.

8. Carefully lay the computer over on its right side (facing the computer) to access the

bottom of the computer.

1-4 Chapter1

Introduction

D Class Mounting Procedures

9. Remove the ﬁve screws holding the skid plate on the front end of the chassis. Refer to

Figure 1-2. This plate is not needed on the computer when it is mounted in the cabinet.

Figure 1-2 Skid Plate

WARNING The next step requires at least two CEs to lift the computer. A fully

loaded D Class computer can weight up to 49.5 kg (110 lbs.). The fully

extended cabinet rails do have some horizontal ﬂex, be sure the tray

is mounted onto the rails with the mounting screws started.

10.Refer to Figure 1-3. Lift the computer (1) and align it over the extended rail and tray

assembly (2). Be sure the extruded feet of the computer ﬁt into the tray cutouts (3).

Chapter 1 1-5

Introduction

D Class Mounting Procedures

Figure 1-3 D Class Mounting Diagram

11.From the front, insert two screws (4) up through the bottom of the tray into the

computer chassis.

12.From the back insert three mounting screws (5) through the tray tabs into the computer

chassis. Be sure all tray mounting screws are tight.

1-6 Chapter1

Introduction

D Class Mounting Procedures

CAUTION If the D Class computer installed into the cabinet has a power select switch

(located on the back of the computer), be sure it is set to the 220V setting.

13.From the bottom, ﬁrmly tighten the four screws attaching the tray and computer to the

rail assemblies ( (6) from Figure 1-1).

14.Attach all appropriate cables to the installed D Class computer(s). This would be

console, I/O, and power cables.

CAUTION DO NOT plug all computer power cords into one PDU, when two PDUs are

installed. Divide the power loading between the two PDUs.

15.Push the computer all the way into the cabinet, then center the slide lockout plate

between both computers. This will prevent a slide from accidentally extending if the

cabinet is bumped or moved.

16.When the computer is fully pushed back into the cabinet, it may be necessary to adjust

the retainer bracket inside the cabinet. This can be done by loosening the retainer

bracket mounting screws and repositioning the bracket in respect to the computers

installed. Insert the two screws through the retainer bracket into the computer chassis

and tighten.

17.Position the cosmetic frame on the cabinet. While holding the cosmetic frame in place,

insert a mounting screw and nylon washer into the tight-clearance-hole (upper left hole

on upper cosmetic frame; lower right hole on lower cosmetic frame). This will keep the

cosmetic frame from falling off while the other screws and nylon washers are being

started.

18.Do a visual inspection of the ﬁt between the cosmetic frame and the computer bezels.

Look for consistent spacing between the frame and bezel. If the ﬁt is skewed, repeat the

procedures in step 16, loosening the retainer bracket to re-align the computer.

19.Plug the PDU power cord(s) into the appropriate wall outlet(s).

20.Put the cabinet power switch into the ON position.

The cabinet and the computers mounted in it are now ready for use. Turn the computers

on and observe them for a normal power on selftest and boot-up process.

D Class 19 Inch Rack Procedures

If the D Class computer is currently mounted in a EIA 19 Inch single mount cabinet, refer

to that cabinets instructions for removing it from that cabinet. To modify the D Class

computer for mounting in the A3764A or A3765A cabinet, perform the following steps:

1. When the computer is fully removed from the 19 inch cabinet, be sure all mounting

hardware from the 19 inch cabinet is removed from the computer.

2. Make sure the skid plate is not on the bottom (at the front) of the computer. If it is,

remove it.

3. Attach the D Class front bezel to the computer. Refer to Figure 1-4.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP 245161-B22 - 10642 42U Rack Shock Pallet Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP E1586A Bedienungsanleitung

HP J1530C Bedienungsanleitung

HP TFT7600 G2 Bedienungsanleitung

HP 355 Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP Z600 - Workstation - 6 GB RAM Bedienungsanleitung

HP Retail Mobile POS Case Bedienungsanleitung

HP LaserJet Enterprise 600 Bedienungsanleitung

HP DL320s - ProLiant 9TB SATA Storage Server... Bedienungsanleitung

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Bedienungsanleitung

HP System/E41 Bedienungsanleitung

HP Intelligent Series Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

HP StorageWorks SSL1016 Bedienungsanleitung

HP RP9 Compact Stand Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Gebrauchsanweisung

HP TS5220 Installationsanleitung

HP cc2300 Bedienungsanleitung

HP MCS 5042 Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung