IFM Electronic Efector100 GG507S Bedienungsanleitung

Original operating instructions

Fail-safe inductive sensor

GG507S

704057 / 02 06 / 2010

Contents

1 Preliminary note��3

1�1 Explanation of symbols��3

2 Safety instructions ��4

2�1 Safety-related requirements regarding the application��4

3 Items supplied��5

4 Functions and features ��5

5 Function��6

5�1 Enable zone��6

5�2 Protection against simple defeating��7

6 Installation��8

7 Electrical connection��8

8 Set-up ��9

8�1 Activate adjustment mode ��9

8�2 Determine the enable zone ��9

8�3 End adjustment mode��10

9 Operation��10

9�1 Sensor signals ��10

9�2 Input characteristics / output characteristics�� 11

9�3 Cross faults �� 11

9�4 Operating mode��12

9�4�1 Delayed switching of the LED��12

9�4�2 Switching of the LED without delay ��13

9�5 Response times��14

9�6 LED display ��15

10 Scale drawing ��16

11 Technical data ��16

12 Troubleshooting ��19

13 Maintenance, repair and disposal��19

14 Approvals / standards ��19

15 Terms and abbreviations��20

1 Preliminary note

The instructions are part of the unit� They are intended for authorised persons

according to the EMC and Low Voltage Directive and safety regulations�

The instructions contain information about the correct handling of the product�

Read the instructions before use to familiarise yourself with operating conditions,

installation and operation�

Adhere to the safety instructions�

1.1 Explanation of symbols

►

Request for action

LED on

LED off

LED flashes

LED flashes quickly



Important note

2 Safety instructions

• Follow the operating instructions�

• Improper use may result in malfunctions of the unit� This can lead to personal

injury and/or damage to property during operation of the machine� For this

reason note all remarks on installation and handling given in these instructions�

Also adhere to the safety instructions for the operation of the whole installation�

• In case of non-observance of notes or standards, specially when tampering

with and/or modifying the unit, any liability and warranty is excluded�

• The unit must be installed, connected and put into operation by a qualified

electrician trained in safety technology�

• The applicable technical standards for the corresponding application must be

complied with�

• For installation the requirements according to EN 60204 must be observed�

• In case of malfunction of the unit please contact the manufacturer� Tampering

with the unit is not allowed�

• Disconnect the unit externally before handling it� Also disconnect any

independently supplied relay load circuits�

• After setup the system has to be subjected to a complete function check�

• Onlyusetheunitunderthespecifiedoperatingconditions(→11Technical

data)� In case of special operating conditions please contact the manufacturer�

• Useonlyasdescribedbelow(→4).

2.1 Safety-related requirements regarding the application

It must be ensured that the safety requirements of the respective application

correspond to the requirements stated in these instructions�

Observe the following requirements:

►Take measures to avoid metallic objects being placed on the sensing face

intentionally or unintentionally�

►Adhere to EN 1088 for interlocking devices associated with guards�

► Adheretothespecifiedoperatingconditions(→11Technicaldata).Useof

the sensor in the vicinity of chemical and biological media as well as ionising

radiation is not permitted�

►Adhere to the principle of normally closed operation for all external safety

circuits connected to the system�

►In case of faults within the fail-safe sensor which result in the defined safe

state: take measures to maintain the safe state when the complete control

system continues to be operated�

►Replace damaged units�

3 Items supplied

1 fail-safe sensor GG507S with 2 M18 mounting nuts,

1 operating instructions GG507S, ident no� 704057�

If one of the above-mentioned components is missing or damaged, please contact

one of the ifm branch offices�

4 Functions and features

The fail-safe inductive sensor detects metal without contact�

Safety function SF: the safe state (output stage switched off; logic "0") is achieved

when undamping greater than or equal to the safe switch-off distance sar

(→11Technicaldata).

Alsoobservethenotesoninstallationofthesensor(→6Installation).

The fail-safe sensor conforms to the category 4 according to EN 954-1 (valid until

31 December 2011), Performance Level e according to EN ISO 13849-1:2008 as

well as to the requirements SIL 3 to IEC 61508�

The unit corresponds to the classification I1A18SP2M to IEC 60947-5-2 for flush

installation(→6Installation).

The fail-safe inductive sensor has been certified by TÜVNord�

5 Function



Dual LED: signal (yellow); power (green)



Fail-safe sensor



Close range



Enable zone



Safe switch-off distance sar



Target

5.1 Enable zone

The output is only enabled when damped in the enable zone� Outside this enable

zone the output remains switched off�

If damped with a standard target plate of 24 x 24 x 1 mm made of FE360 (= mild

steel) and flush installation to IEC 60947-5-2 the enable zone is in the range of

1��4 mm�

The safe switch-off distance sar is > 10 mm�

The enable zone is different if damping elements which deviate from the standard

target plate in terms of material, form and size are used�

Enable zone for other materials*:

Material Enable zone

steel FE360 1��4 mm

stainless steel 1�4301/304S15 0�4��2�7 mm

AIMg3G22 0��1�4 mm

CuZn37 0��1�5 mm

Cu 0��0�8 mm

* Typical values for damping with a reference target of 24 x 24 x 1 mm and flush installation

to IEC 60947-5-2 at an ambient temperature of 20°C�

5.2 Protection against simple defeating

The fail-safe sensor reacts to metal objects, e�g� the frame of a security door�

Other metal objects that are not intended to enable the sensor must not be

allowed to enable the fail-safe sensor, either intentionally or unintentionally�



►Take measures to prevent metal objects, except the designated target,

from being placed on the sensing face or in the enable zone intentionally

or unintentionally�

In addition, the sensor has the following switching characteristics to make simple

defeating of its safety function more difficult:

1� By slowly introducing a metallic object into the enable zone, the output is

immediately switched, but displayed by the signal LED with a delay of about

3s(→9.4.1DelayedswitchingofthesignalLED).Bydoingso,theobject

is generally in the close range before the LED indication is lit� The technical

instructions concerning the restart of the installation must be observed�

2� If the object stays in the close range for longer than approx� 2 s, the output is

completely disabled and no longer enabled if damped in the enable zone� If

the object stays in the close range for longer than approx� 5 s, the adjustment

modeisactivated(→8.1Activateadjustmentmode).

Release of the enable zone can be carried out

•either by undamping (> 10 mm) for a time of more than 2 s

•or by a voltage interruption

(→8.3Endadjustmentmode).

6 Installation

The unit is flush mountable according to IEC 60947-5-2, type I1A18SP2M�

►Ensure the unit cannot work loose� Maximum tightening torque: 40 Nm

►Adhere to the installation conditions in accordance with the figures 1 to 3:

123

7 Electrical connection

Wiringdiagram→11Technicaldata

►Disconnect the unit� Also disconnect any independently supplied relay load

circuits�

►Supply voltage: connect L+ to pin 1 and L- to pin 3 of the connector�



The nominal voltage is 24 V DC� This voltage may vary between 19�2 V and

30 V incl� 5% residual ripple to EN 61131-2�



In case of one fault the supply voltage must not exceed 60 V DC for more

than 0�2 s up to a max� value of 120 V DC (this corresponds to SELV to

EN 60950-1)�



For unit with cULus approval and the scope of validity cULus:

The device shall be supplied from an isolating transformer having a

secondary listed fuse rated either

a) max� 5 amps for voltages 0~20 Vrms (0~28�3 Vp) or

b) 100/Vp for voltages of 20~30 Vrms (28�3~42�4 Vp)�

8 Set-up

8.1 Activate adjustment mode

For easy and reliable installation the sensor can be put in the adjustment mode�

100 mm

> 5 s

Signal

Power

This is done by placing a metallic

object directly in front of the sensing

face of the fail-safe sensor (close

range)�

After approx� 5 s the yellow signal

LED starts to flash: the adjustment

mode is active�

As long as this mode is active, the

output stage remains in the safe

state ("0")�



Close range



Enable zone

8.2 Determine the enable zone

If the sensor is in the adjustment mode, the enable zone of the sensor can be

determined by moving the damping element�

100 mm

Signal

Power

Signal

Power

Signal

Power

As soon as damping is carried out

in the enable zone, the yellow LED

goes out�

If the target is in the close range or in

the immediate vicinity of the enable

zone, the LED starts to flash again�



Close range



Enable zone

8.3 End adjustment mode

< 2 s

Signal

Power

> 2 s

Signal

Power

100 mm

If the sensor is undamped for more

than 2 s (> 10 mm), the adjustment

mode is switched off and the yellow

LED goes out�

This can also be achieved by power

off�



Close range



Enable zone

9 Operation

9.1 Sensor signals

The safe state is when the output is switched off (zero-current state: logic "0")� The

fail-safe sensor must be operated with a clock signal on its clock input (TE)� The

clock input signal must meet the defined time conditions (see figure)�

T1 T2

T1≥50ms

T2≥50ms

T = 100��500 ms

td = 1�0��1�5 ms (± 10 %)



Clock input (TE)



Output

Andere Handbücher für efector100 GG507S

Inhaltsverzeichnis

Andere IFM Electronic Zubehör Handbücher

IFM Electronic

IFM Electronic Ecomat200 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 500 PM2055 Bedienungsanleitung

IFM Electronic

IFM Electronic LK8122 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic O1D102 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 OL Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SM8000 Bedienungsanleitung

IFM Electronic

IFM Electronic PN50 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SBU3 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 300 SA1004 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SU8200 Bedienungsanleitung

IFM Electronic

IFM Electronic GF711S Bedienungsanleitung

IFM Electronic

IFM Electronic efector 250 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 150 KG5070 Bedienungsanleitung

IFM Electronic

IFM Electronic efector500 PI20 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 OL Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector230 UGA Bedienungsanleitung

IFM Electronic

IFM Electronic LR3000 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ50 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OW Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 300 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 250 Bedienungsanleitung

IFM Electronic

IFM Electronic TUV NORD Efector 110 GM701S Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung

IFM Electronic efector100 GG507S Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken