IFM Electronic Efector200 OL Bedienungsanleitung

Operating instructions

Diffuse reflection sensor

701271 / 04 12 / 2010

Contents

Function and features��3

Electrical connection��3

Montage��4

Commissioning��4

Setting of the sensitivity with stationary objects ��5

Setting of the sensitivity with moving objects ��6

Setting of the maximum sensitivity ��7

Programming the output function ��7

Operation��8

Maintenance��8

Function and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switched signal�

Range (r): see type label (value referred to white paper 200 mm x 200 mm)�

Electrical connection

►Isolate power, then connect the unit�

►Connect the unit as follows:

AC/DC Relais

Sensor with terminals Sensor with connector































Insert a miniature fuse according to the technical data sheet, if specified�

Core colours (for sensors with cable connection): BN = brown, BU = blue,

BK = black, WH = white�

Programming of the output function by push button (see page 7)�

The units with cable gland have a removable terminal block with screw terminals

(screws are at the base of the terminal block)�

After connection of the wires the terminal block must be reinserted�

Check the unit for reliable function after a short cirucit�

Montage

1: LEDs red, green, yellow

2: Pushbutton

3: LED yellow

Align the photocell and fasten it to a mounting bracket�

Maximum range is only possible with precise alignment�

Commissioning

The diffuse reflection sensor is supplied ready to operate (plug and play) set at the

max� sensing range� This is sufficient if the diffuse reflection sensor can operate

with maximum excess gain (highest contrast)�

The following setting procedures should only be necessary in less straightforward

applications, for example if a background must be „tuned out“�

Setting of the sensitivity with stationary objects

►Activate the programming mode of the unit without object�

►Press for about 2 s until the red LED flashes�

> The red LED goes out; the yellow and green LEDs flash alternately�

> The unit is in the programming mode�

Setting with object�

►Press once�

> The yellow and green LEDs go out for approx� 1 s, then flash again alternately�

Setting without object�

►Press once�

> The yellow and green LEDs go out for approx� 1 s�

> After approx� 3 s the green LED is on�

> The unit is in the operating mode��

You can also proceed in reverse order: first setting without the object, then with

the object�

If the setting of the sensitivity is not possible (e�g� object signal and

background signal are about the same), the red LED flashes after step

3 for approx� 2 s� The unit then passes into the operating mode with the

sensitivity being unchanged�

If the setting button is not activated for 15 minutes during the programming

process, the unit passes automatically into the operating mode with the sensitivity

being unchanged�

Setting of the sensitivity with moving objects

►Activate the programming mode of the unit without object�

►Press for about 2 s until the red LED flashes�

> The red LED goes out; the yellow and green LEDs flash alternately�

> The unit is in the programming mode�

►During the measurement (approx� 1 s) allow at least two objects to move through

the sensing area of the lens�

►Press once�

> The yellow and green LEDs go out for approx� 1 s, then flash again alternately�

►During the measurement (approx� 1 s) allow at least two objects to move through

the sensing area of the lens�

►Press once�

> The yellow and green LEDs go out for approx� 1 s�

> After approx� 3 s the green LED is on�

> The unit is in the operating mode�

If the setting of the sensitivity is not possible (e�g� object signal and

background signal are about the same), the red LED flashes after step

3 for approx� 2 s� The unit then passes into the operating mode with the

sensitivity being unchanged�

Setting of the maximum sensitivity

• Go into the programming mode (step 1)�

• Align the unit so that no light is reflected�

• Press the setting button twice (see steps 2 and 3)�

Programming the output function

►Press for 10 s�

The red LED starts to flash fast after 2 s�

Then the yellow and green LEDs flash

alternately� After 8 s all LEDs go off,

the output function has changed from

light-on mode to dark-on mode (or vice

versa)�

Operation

Check the safe functioning of the sensor� Display by LEDs�

LED green lights Unit is ready for operation�

LED yellow lights Output is switched�

LED red lights Error in object detection, e�g� maladjustment,

soiling of the lenses�

LEDs yellow + red

Flash alternately, 2 Hz: output short-circuited�

Flash alternately, 1 Hz: internal malfunction,

(output is not switched)�

Maintenance

Keep the lens of the sensor free from soiling�

For cleaning do not use any solvents or cleaning agents which could damage the

plastic lenses�

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Electronic Zubehör Handbücher

IFM Electronic

IFM Electronic O5H Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ50 Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic LR2750 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SU8001 Bedienungsanleitung

IFM Electronic

IFM Electronic efector200 OG Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic LR8300 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SI5004 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 300 Bedienungsanleitung

IFM Electronic

IFM Electronic SA 00 Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efectror 200 OGE2 Series Bedienungsanleitung

IFM Electronic

IFM Electronic LR2059 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ51 Series Bedienungsanleitung

IFM Electronic

IFM Electronic ID000A Bedienungsanleitung

IFM Electronic

IFM Electronic Efectorsod PE70 Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 500 PP70 Series Bedienungsanleitung

IFM Electronic

IFM Electronic O3M151 Betriebsanleitung

IFM Electronic

IFM Electronic efector 250 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 160 LR8300 Bedienungsanleitung

IFM Electronic

IFM Electronic efectro 200 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OIH5 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 O5 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung

IFM Electronic efector200 OL Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken