IFM Electronic Efector500 PQ08 Series Bedienungsanleitung

Operating instructions

Pressure sensor

PQ08xx

704940/01 03/2011

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��4

4 Function��4

4�1 Processing of the measured signals��4

4�2 Switching function��4

4�3 Diagnostic function ��5

5 Mounting��6

5�1 Mounting accessories��6

5�2 DIN rail mounting��6

5�3 Rear panel mounting ��7

6 Electrical connection��7

7 Operating and display elements ��8

8 Menu��9

8�1 Menu structure��9

8�2 Explanation of the menu��10

9 Parameter setting �� 11

9�1 General parameter setting�� 11

9�2 Setting of the output signals ��13

9�2�1 Setting of the unit of measurement for system pressure ��13

9�2�2 Setting of the output function��13

9�2�3 Setting of the switching limits (hysteresis function) ��13

9�2�4 Setting of the switching limits (window function) ��13

9�3 User settings (optional) ��14

9�3�1 Setting of a time delay for the switching signals��14

9�3�2 Setting of the damping for the switching outputs��14

9�3�3 Configuration of the display ��14

9�3�4 Zero point calibration ��15

9�4 Service functions ��15

9�4�1 Reading of the min/max values for system pressure��15

9�4�2 Reset of all parameters to factory setting ��15

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note:

Non-compliance can result in malfunctions or interference�

2 Safety instructions

• Please read this document prior to set-up of the unit� Ensure that the product is

suitable for your application without any restrictions�

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property can occur�

• Checkthecompatibilityoftheproductmaterials(→chapter12Technicaldata)

with the media to be measured in all applications�

For the scope of validity cULus:

Thedeviceshallbesuppliedfromanisolatingtransformerhavingasecondary

Listed fuse rated either

a) max 5 amps for voltages 0~20 Vrms (0~28�3 Vp) or

b) 100/Vp for voltages of 20~30 Vrms (28�3~42�4 Vp)�

TheSensorshallbeconnectedonlybyusinganyR/C(CYJV2)cord,havingsuit-

able ratings�

10 Operation��16

10�1 Reading of the set parameters ��16

10�2 Fault indication ��16

11 Scale drawing ��17

12 Technicaldata��18

12�1 Setting ranges ��19

13 Werkseinstellung ��19

3 Functions and features

Theunitmonitorsthesystempressureinpneumaticandcompressedairnetworks

of machines and plants�

Applications

Compressed air (other media on request)

Typeofpressure:relativepressure

Order no. Measuring range Permissible

overpressure Bursting pressure

bar PSI bar PSI bar PSI

PQ0809 -1��1 -14�5��14�5 20 290 30 435

PQ0834 -1��10 -14�5��145 20 290 30 435

MPa = bar ÷ 10 / kPa = bar × 100

Avoid static and dynamic overpressure exceeding the given overload pres-

sure by taking appropriate measures�

Theindicatedburstingpressuremustnotbeexceeded.

Even if the bursting pressure is exceeded only for a short time, the unit

maybedestroyed.NOTE:Riskofinjury!

4 Function

4.1 Processing of the measured signals

• Theunitdisplaysthecurrentsystempressure.

• It generates 2 output signals according to the parameter setting�

OUT1 •Switching signal for system pressure limit value�

OUT2

2 options

•Switching signal for system pressure limit value�

•Diagnostic signal (output 1 is inactive in case of a fault)�

4.2 Switching function

OUTxchangesitsswitchingstateifitisaboveorbelowthesetswitchinglimits

(SPx,rPx).Thefollowingswitchingfunctionscanbeselected:

• Hysteresisfunction/normallyopen:[oux]=[Hno](→fig.1).

• Hysteresisfunction/normallyclosed:[oux]=[Hnc](→fig.1).

First the set point (SPx) is set, then the reset point (rPx) with the requested differ-

ence�

• Windowfunction/normallyopen:[oux]=[Fno](→fig.2).

• Windowfunction/normallyclosed:[oux]=[Fnc](→fig.2).

ThewidthofthewindowcanbesetbymeansofthedifferencebetweenFHxand

FLx� FHx = upper value, FLx = lower value�













































1 2

P=systempressure;HY=hysteresis;FE=window

4.3 Diagnostic function

Output 2 is used as diagnostic output based on the DESINA specification if

[ou2] = [diA]�

• If there is no fault, the output is switched and carries Ub- �

• In case of malfunctions in the following areas, the output is inactive:

- short circuit in output 1�

- EPROM function�

- RAM function�

- parameter setting�

- processor function�

5 Mounting

Before installing and removing the unit: make sure that no pressure is

applied to the system.

►Screw the pressure connection or

adapter G⅛to the main pressure

connection (1) and tighten.

Maximum tightening torque: 8 Nm.

Maximum thread length: 7.5 mm.

5.1 Mounting accessories

The following components are available as accessories: Order no.

Mounting set for DIN rail mounting (DIN rail TH 35-7.5 to EN 60715) E37340

Thread extension 1/8“ for flange mounting E30075

Push-in air fitting for tube Ø 6 mm E30076

Push-in air fitting for tube Ø 8 mm E30077

5.2 DIN rail mounting

DIN rail TH 35-7.5 to EN 60715

►Fix the mounting clip (1) with the screws M4 x 35 (2) to the flange. Maximum

tightening torque: 2.5 Nm.

►Hook the unit into the DIN rail and clip it into place.

Removal:

►Lever out the mounting clip with a screwdriver at the top or at the bottom and

remove the unit�

5.3 Rear panel mounting

►Fix the unit with 2 screws M4 x 35 (1) (not included) to the rear panel� Maxi-

mum tightening torque: 2�5 Nm�

6 Electrical connection

Theunitmustbeconnectedbyaqualifiedelectrician.

Thenationalandinternationalregulationsfortheinstallationofelectrical

equipment must be adhered to�

Voltage supply to EN 50178, SELV, PELV�

►Disconnect power�

►Connect the unit as follows:

L+

Out 1

Out 2

Pin 1 Ub+

Pin 3 Ub-

Pin 4 (OUT1) •binary switching output pressure monitoring

Pin 2 (OUT2) •binary switching output if [ou2] = [Hno], [Hnc], [Fno] or [Fnc]

•diagnostic output if [ou2] = [diA]

7 Operating and display elements

1 2 3 4 5 6 78

Mode/Enter Set

1 to 8: Indicator LEDs

- LED 1 to LED 4 = system pressure in the unit of measurement which is indicated on the

label�

- LEDs 5 to 6: not used,

- LED 7, LED 8 = switching state of the corresponding output�

9: Alphanumeric display, 4 digits

- Indication of the current system pressure�

- Indication of the parameters and parameter values�

10: Set button

- Setting of the parameter values (scrolling by holding pressed; incrementally by pressing

once)�

11: Mode/Enter button

- Selection of the parameters and acknowledgement of the parameter values

8 Menu

8.1 Menu structure

RUN

8.2 Explanation of the menu

SP1/rP1 Upper/lowerlimitvalueforsystempressureatwhichOUT1switches.

FH1/FL1 Upper/lowerlimitfortheacceptablerange(monitoredbyOUT1).

SP2/rP2 Upper/lowerlimitvalueforsystempressureatwhichOUT2switches.

FH2/FL2 Upper/lowerlimitfortheacceptablerange(monitoredbyOUT2).

EF Extended functions / opening of menu level 2�

rES Restore factory settings�

dS1 TimedelayforSP1/FH1.

dS2 TimedelayforSP2/FH2.

dr1 TimedelayforrP1/FL1.

dr2 TimedelayforrP2/FL2.

ou1 OutputfunctionforOUT1:

• Switching signal for the pressure limit values: hysteresis function [H ��] or

window function [F ��], either normally open [� no] or normally closed [� nc]�

ou2 OutputfunctionforOUT2:

• Switching signal for the pressure limit values: hysteresis function [H ��] or

window function [F ��], either normally open [� no] or normally closed [� nc]�

• Diagnostic signal [ou2] = diA�

uni Standard unit of measurement for system pressure�

Lo Maximum value memory for system pressure�

Hi Minimum value memory for system pressure�

dAP Damping for the switching outputs�

coF Manually enter the zero point calibration�

tcoF Teachzero-pointcalibration.

diS Update rate and orientation of the display�

cLor Colour of the digital display (permanent or alternating with switching status

OUT1).

Inhaltsverzeichnis

Andere IFM Electronic Zubehör Handbücher

IFM Electronic

IFM Electronic Efector 300 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ51 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector160 LI51 Bedienungsanleitung

IFM Electronic

IFM Electronic efector200 OT Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efectorsod PE70 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector500 PI20 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 410 JN2100 Anwendungshandbuch

IFM Electronic

IFM Electronic efector160 LI214 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector180 IX50 Bedienungsanleitung

IFM Electronic

IFM Electronic O1D100 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ50 Series Bedienungsanleitung

IFM Electronic

IFM Electronic LR7300 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector160 LK3 Bedienungsanleitung

IFM Electronic

IFM Electronic OPD100 Bedienungsanleitung

IFM Electronic

IFM Electronic SB 4 Series Bedienungsanleitung

IFM Electronic

IFM Electronic VKV021 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 OL Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector230 Bedienungsanleitung

IFM Electronic

IFM Electronic O5E5 A Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector200 OGP50 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 250 O2D22x Bedienungsanleitung

IFM Electronic

IFM Electronic efector500 PC3 Series Bedienungsanleitung

IFM Electronic

IFM Electronic SU7000 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung

IFM Electronic efector500 PQ08 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken