IFM O5E7 Series Bedienungsanleitung

Operating instructions

Through-beam sensor

O5E7xx

O5S7xx

80284275 / 00 04 / 2019

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure.

Visible laser light; CLASS 1 LASER PRODUCT.

EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR

1040 except for deviations pursuant to Laser Notice No. 50, dated June

2007

Position of the product label Additional label

3 Functions and features

The through-beam sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range 60 m.

4 Installation

transmitter receiver

►Install the receiver (O5E...) and secure it to a bracket.

►Align the transmitter (O5S...) to the receiver and fix it.

Maximum range is only possible with precise alignment.

5 Operating and display elements

receiver







1: LED

2: [OUT on]

3: [OUT o󰀨]

6 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of

electrical equipment must be adhered to.

►Voltage supply according to EN 50178.

►Disconnect power.

►Connect the unit as follows:

Receiver DC PNP











pin 1 = L+ (10...36 V DC)

(pin 2 = not connected)

pin 3 = L-

pin 4 = load (PNP, 200 mA)

Transmitter DC

L+

pin 1 = L+ (10...36 V DC)

(pin 2 = not connected)

pin 3 = L-

(pin 4 = not connected)

7 Settings

7.1 The sensor is to switch when the object is detected

►Position the object

receiver transmitter

►Press [OUT on] for 2 s.

> The sensitivity is set to the object.

> The yellow LED flashes.

►Remove the object

receiver transmitter

►Press [OUT off].

> The sensitivity is set without object.

> The yellow LED goes out. The programming is finished.

7.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off].

►Remove the object (see figure 2) and press [OUT on].

The setting can also be carried out first without object and then with object.

7.3 Setting of the maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

7.4 Programming unsuccessful

> The LED flashes quickly, 8 Hz.

• Measured value difference too small.

• Max. programming time of 15 min. exceeded.

7.5 Electronic lock

Lock or unlock the buttons

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED status.

8 Operation

►Check whether the units operate correctly.

> Receiver: The LED lights when the switching output is switched.

9 Maintenance, repair and disposal

►Keep the front panes of the sensors free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material.

►Do not try to open the module enclosure. There are no user - serviceable

components inside.

Technical data and further information at www.ifm.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Zubehör Handbücher

IFM

IFM OGE7 Series Bedienungsanleitung

IFM

IFM PN7160 Bedienungsanleitung

IFM

IFM Efector 500 PY2068 Bedienungsanleitung

IFM

IFM VNB211 Bedienungsanleitung

IFM

IFM Efector 500 PI30 Bedienungsanleitung

IFM

IFM efector200 OOF Series Bedienungsanleitung

IFM

IFM Efector 160 LR70 Bedienungsanleitung

IFM

IFM MFH Bedienungsanleitung

IFM

IFM O2D54 Series Bedienungsanleitung

IFM

IFM SB0503 Bedienungsanleitung

IFM

IFM OID20 Series Bedienungsanleitung

IFM

IFM O1D111 Bedienungsanleitung

IFM

IFM PN3 Series Bedienungsanleitung

IFM

IFM PT24 Series Bedienungsanleitung

IFM

IFM efector 200 OGP2 Series Bedienungsanleitung

IFM

IFM O3M150 Montageanleitung

IFM

IFM PC3 Series Bedienungsanleitung

IFM

IFM efector 200 OGH Bedienungsanleitung

IFM

IFM PI17 Series Bedienungsanleitung

IFM

IFM SI 5000 Bedienungsanleitung

IFM

IFM O5E5 Series Bedienungsanleitung

IFM

IFM UGT204 Bedienungsanleitung

IFM

IFM PN72 Series Bedienungsanleitung

IFM

IFM PF295 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung