IFM OGP7 Series Bedienungsanleitung

Operating instructions

Retro-reflective sensor

OGP7xx

80284283 / 00 04 / 2019

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure.

Visible laser light; CLASS 1 LASER PRODUCT.

EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR

1040 except for deviations pursuant to Laser Notice No. 50, dated June

2007

Position of the product label Additional label

3 Functions and features

In conjunction with a prismatic reflector or reflective tape the retro-reflective

sensor detects objects and materials without contact and indicates their presence

by a switching signal.

Range: www.ifm.com → Select your country → Data sheet direct: e.g. OGE700.

4 Installation





1: LED

►Fit the prismatic reflector or the reflective tape behind the object to be detected.

►Align the retro-reflective sensor to it and secure it to a bracket.

Maximum range is only possible with precise alignment.

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of electri-

cal equipment must be adhered to.

►Voltage supply according to EN 50178.

►Disconnect power.

►Connect the unit as follows:

DC PNP











pin 1 = L+ (10...36 V DC)

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

6 Settings

6.1 The sensor is to switch when the object is detected

►Position the object.





►Press [OUT on] for 2 s.

> The LED flashes.

►Remove the object.





►Press [OUT off].

> The LED goes out. The programming is finished.

6.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off] for 2 s.

►Remove the object (see figure 2) and press [OUT on].

The setting can also be carried out first without object and then with object.

6.3 Setting of the maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected.

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

First press [OUT off], then [OUT on].

6.4 Programming unsuccessful

> The yellow LED flashes quickly (8 Hz).

• Insufficient difference in measurements.

• Max. programming time (15 min.) exceeded.

6.5 Electronic lock

Lock or unlock the buttons

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED status.

7 Operation

►Check whether the unit operates correctly.

> The LED lights when the switching output is switched.

8 Maintenance, repair and disposal

►Keep the front pane of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material.

►Do not try to open the module enclosure. There are no user - serviceable

components inside.

Technical data and further information at www.ifm.com

Inhaltsverzeichnis

Andere IFM Zubehör Handbücher

IFM

IFM Efector 160 LR70 Bedienungsanleitung

IFM

IFM O2D50 Series Bedienungsanleitung

IFM

IFM Efector 200 O4P5 Series Bedienungsanleitung

IFM

IFM Efector 200 OJ Bedienungsanleitung

IFM

IFM OY Series Bedienungsanleitung

IFM

IFM Efector 500 PI30 Bedienungsanleitung

IFM

IFM OY4**S Series Bedienungsanleitung

IFM

IFM Efector 500 PY2068 Bedienungsanleitung

IFM

IFM efector160 LR2750 Bedienungsanleitung

IFM

IFM GI854S Bedienungsanleitung

IFM

IFM LDH100 Bedienungsanleitung

IFM

IFM O8H2 Bedienungsanleitung

IFM

IFM OGD25 Series Bedienungsanleitung

IFM

IFM efector 200 O4H5 Series Bedienungsanleitung

IFM

IFM efector200 OOF Series Bedienungsanleitung

IFM

IFM OGE Bedienungsanleitung

IFM

IFM KB Bedienungsanleitung

IFM

IFM Efector 500 PF2652 Bedienungsanleitung

IFM

IFM TK61 Series Bedienungsanleitung

IFM

IFM O5H5 Series Bedienungsanleitung

IFM

IFM O6P7 Series Bedienungsanleitung

IFM

IFM Efector 100 GG712S Bedienungsanleitung

IFM

IFM Efector 500 PM2655 Bedienungsanleitung

IFM

IFM Efector 500 PI2652 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung