Impex COMPETITOR CB-430 Bedienungsanleitung

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

Model

CB-430

Retain This

Manual for

Reference

07-03-03

OWNER'S

MANUAL

COMPETITOR BENCH

CB-430

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................…. 1

IMPORTANT SAFETY NOTICES..................................................................…. 2

HARDWARE IDENTIFIER.....…....................................................................…. 3

ASSEMBLY INSTRUCTIONS........................................................................…. 4

EXPLODED DIAGRAM………………………………………………………………. 10

PARTS LIST...............................................................................................……. 11

WARRANTY.................................................................................................…. 12

ORDERING PARTS.......................................................................................… 12

BEFORE YOU BEGIN

Thank you for selecting the COMPETITOR CB-430 Bench by IMPEX

FITNESS PRODUCTS. For your safety and benefit, read this manual

carefully before using the machine. As a manufacturer, we are committed

to provide you complete customer satisfaction. If you have any questions, or

find there are missing or damaged parts, we guarantee you complete

satisfaction through direct assistance from our factory. To avoid

unnecessary delays, please call our TOLL-FREE customer service number.

Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave

children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water

or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or

other clothing that could become caught in the machine. Running or aerobic shoes are

also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use

attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in

attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm

up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE

OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES

NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE

SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

HARDWARE IDENTIFIER

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen

Wrenches

NOTE: It is strongly recommended two or more people assembling this machine to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Front Stabilizer (#22) to the Main Frame (#4). Secure it with two M10 x 3

1/8” Carriage Bolts (#54), one 4 ¾” x 1 5/8” Bracket (#26), two ∅¾” Washers (#64),

and two M10 Aircraft Nuts (#63).

B.) Connect the two Rear Stabilizers (#5) with the Lat Bar Base (#6). Attach the Main

Frame (#4) to the Lat Bar Base. Secure them together with two M10 x 3 3/8” Carriage

Bolts (#52), ∅¾” Washers (#64), and M10 Aircraft Nuts (#63). Diagram 1

STEP 2 (See Diagram 2)

A.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#1). Insert the Lat Bar

Frame into the opening on the Lat Bar Base (#6).

B.) Attach the Cross Brace (#7) to the Lat Bar Base. Align the holes on the Lat Bar Frame,

Lat Bar Base, and Cross Brace. Secure them with three M10 x 2 ¾” Carriage Bolts

(#56), one 1 5/8” x 2” Bracket (#38), one 6 ¾” x 2” Bracket (#39), three ∅¾” Washers

(#64), and three M10 Aircraft Nuts (#63). Do not tighten the nuts and bolts yet.

C.)Place the Backrest Adjustment Bar (#10) onto the holders on the Cross Brace.

D.)Attach two Spring Clips (#34) onto the weight posts on the Sliding Weight Post (#11).

E.) Insert one M10 x 2 3/8” Allen Bolt (#67) through the hole on the Lat Bar Frame. Secure

it with two Ø ¾” Washers (#64) and one M10 Aircraft Nut (#63).

DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Attach the bottom of Right Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right

Upright Beam to the Cross Brace (#7).

B.) Secure the Right Upright Beam to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts

(#54), ∅¾” Washers (#64), and M10 Aircraft Nuts (#63).

C.) Secure the Right Upright Beam to the Cross Brace with two M10 x 2 ¾” Carriage Bolts

(#56), one 4 ¾” x 2” Bracket (#27), two ∅¾” Washers (#64), and two M10 Aircraft Nuts

(#63).

D.) Repeat Steps A, B, and C above to install the Left Upright Beam (#2).

E.) Insert the Left & Right Bar Holders (#23 & 24) into the selected holes on the Upright Beam.

DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball

stopper of the Cable is underneath the Frame.

B.) Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø 5/8”

Pulley Bushings (#43), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

C.)Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket. Secure

it with one M10 x 2” Allen Bolt (#55), one L-shaped Pulley Bracket (#28), two ∅¾” Washers

(#64), and one M10 Aircraft Nut (#63).

D.)Pull the Cable down to the Sliding Weight Post (#11). Secure the Cable to the Post with one M10

x 1 3/8” Allen Bolt (#53), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

E.) Connect a Chain (#37) to the Lat Bar (#12) with a C-clip (#36). Connect the Chain to the Cable

with another C-clip.

STEP 5 (See Diagram 5)

A.) Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2

½” Allen Bolt (#57), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

B.) Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15).

Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1

3/8” Hex Bolts (#58) and ∅½” Washers (#66).

C.)Place the Seat (#18) onto the Seat Support (#15). Secure it with four M6 x 5/8” Hex Bolts

(#60) and ∅½” Washers (#66). Insert a L-shaped Pin (#40) into the hole on the Seat Support

to lock the Seat and Backrest Board in position. Remove the Pin when folding the Backrest

Board forward to allow access to the “Walk-in Squat”.

D.)Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Hex

Bolts (#61) and ∅5/8” Washers (#65).

E.) Insert the Arm Curl Stand into the opening on the Main Frame. Secure it with a M10 Lock

Knob (#33). DIAGRAM 5

STEP 6 (See Diagram 6)

A.) Attach the Leg Developer (#8) to the Main Frame. Secure it with M10 x 3” Allen Bolt

(#59), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

B.) Insert one Foam Tube (#25) halfway through the hole on the Main Base Frame. Insert

two Foam Tubes halfway through the holes on the Leg Developer.

C.) Push six Foam Rolls (#31) onto the Foam Tubes from both ends.

D.) Attach the Curl Bar Handle Frame (#13) to the Leg Developer. Secure it with a L-

shaped Pin (#40). Remove the Pin and the Curl Bar when doing Leg Developer

exercises.

E.) Attach a Spring Clip (#34) to the weight post on the Leg Developer.

DIAGRAM 6

Inhaltsverzeichnis

Andere Impex Heim-Fitnessstudio Handbücher

Impex

Impex IGS-5100 Bedienungsanleitung

Impex

Impex MARCY MWM-7300 Bedienungsanleitung

Impex

Impex MWB-50100 Bedienungsanleitung

Impex

Impex IRON GRIP STRENGTH TSA-88 Bedienungsanleitung

Impex

Impex MARCY WM-367 Bedienungsanleitung

Impex

Impex IRONGRIP IGS-04 Bedienungsanleitung

Impex

Impex Marcy SB-662 Bedienungsanleitung

Impex

Impex OLYMPIAN Bedienungsanleitung

Impex

Impex MWB-838 Bedienungsanleitung

Impex

Impex Iron Grip Sport IGS-07 Bedienungsanleitung

Impex

Impex APEX TSA-499 Bedienungsanleitung

Impex

Impex MARCY PRO SM-7409 Bedienungsanleitung

Impex

Impex CB-339 Bedienungsanleitung

Impex

Impex Powerhouse Club PHC 715 Bedienungsanleitung

Impex

Impex WM-MXS Bedienungsanleitung

Impex

Impex MARCY MWM-1860 Bedienungsanleitung

Impex

Impex Apex TC-3500 Bedienungsanleitung

Impex

Impex MD-860 Bedienungsanleitung

Impex

Impex POWERHOUSE JD 1 Bedienungsanleitung

Impex

Impex MARCY CR 5 Bedienungsanleitung

Impex

Impex TSA-42 Bedienungsanleitung

Impex

Impex MARCY MD-2082W Bedienungsanleitung

Impex

Impex APEX II Bedienungsanleitung

Impex

Impex MARCY MCB-346 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Weider

Weider 8300 Hard Drive Bedienungsanleitung

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Weider

Weider 8700 I Kurzanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung