Intel NUC 8 Enthusiast Bedienungsanleitung
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
1
Intel® NUC 8 Business, a Mini PC with Windows® 10 –NUC8i7HNKQC
Intel® NUC 8 Enthusiast, a Mini PC with Windows® 10 –NUC8i7HVKVA
User
Guide
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
2
Before You Begin
CAUTIONS
The procedures in this user guide assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance required for using
and modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications link or network before
performing any of the procedures described in this guide. Failure to disconnect power,
telecommunications links, or networks before you open the computer or perform any procedures can
result in personal injury or equipment damage. Some circuitry on the board can continue to operate even
though the front panel power button is off.
Follow these guidelines before you begin:
Always follow the steps in each procedure in the correct order.
Set up a log to record information about your computer, such as model, serial numbers,
installed options, and configuration information.
Electrostatic discharge (ESD) can damage components. Perform the procedures described in
this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam
pad. If such a station is not available, you can provide some ESD protection by wearing an
antistatic wrist strap and attaching it to a metal part of the computer chassis.
Installation Precautions
When you install and test the Intel NUC, observe all warnings and cautions in the installation
instructions.
To avoid injury, be careful of:
Sharp pins on connectors
Sharp pins on circuit boards
Rough edges and sharp corners on the chassis
Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical
personnel.
Observe Safety and Regulatory Requirements
If you do not follow these instructions, you increase your safety risk and the possibility of
noncompliance with regional laws and regulations.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
3
This guide tells you how to:
•
Open and Close the Chassis
•
Install and Remove Memory
•
Install an M.2 SSD
•
Install a VESA Mount Bracket
•
Connect Power
•
Install an Operating System
•
Install the latest device drivers and software
•
Operating System Recovery
Open the Intel NUC Chassis
To open the Intel NUC chassis, follow these steps:
1. Using the included hex wrench, unscrew the six screws on the top cover of the chassis and lift the
cover.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
4
2. Detach the cable from the top of the NUC.
3. Unscrew the single screw to release the top plate.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
5
Installing and Removing Memory
The Intel NUC 8 Business - NUC8i7HNKQC and Intel NUC 8 Enthusiast - NUC8i7HVKVA have two 260-pin
DDR4 SO-DIMM sockets. Although these NUCs come with both memory slots filled, follow these steps if
memory is removed or installed.
Pre-installed memory
Intel® NUC 8 Business, a Mini PC with Windows® 10 –NUC8i7HNKQC
Two 8GB memory
modules
16GB total
Intel® NUC 8 Enthusiast, a Mini PC with Windows® 10 –NUC8i7HVKVA
Two 8GB memory
modules
16GB total
Memory requirements:
1.2V low voltage memory
2400 MHz SO-DIMMs
Non-ECC
Find tested memory at the Intel® Product Compatibility Tool:
NUC8i7HNKQC
NUC8i7HVKVA
NOTE
If only installing one SO-DIMM, install it in the lower memory socket.
To install memory, follow these steps:
1. Observe the precautions in "Before You Begin" on page 2.
2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect
the AC power cord.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
6
3. Align the small notch at the bottom edge of the SO-DIMM with the key in the socket.
4. Insert the bottom edge of the SO-DIMM into the socket.
5. When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the
retaining clips snap into place. Make sure the clips are firmly in place.
To remove memory, follow these steps:
1. Observe the precautions in “Before You Begin” on page 2.
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
3. Remove the AC power cord from the computer.
4. Remove the computer’s cover.
5. Gently spread the retaining clips at each end of the SO-DIMM socket. The SO-DIMM pops out of
the socket.
6. Hold the SO-DIMM by the edges, lift it away from the socket, and store it in an anti-static package.
7. Reinstall and reconnect any parts you removed or disconnected to reach the SO-DIMM sockets.
8. Replace the computer’s cover and reconnect the AC power cord.
Installing an M.2 SSD
The Intel NUC 8 Business - NUC8i7HNKQC and Intel NUC 8 Enthusiast - NUC8i7HVKVA support both
80mm and 42mm SSDs.
Find compatible M.2 SSDs at the Intel® Product Compatibility Tool:
NUC8i7HNKQC
NUC8i7HVKVA
To install an 80mm M.2 SSD:
1. Remove the small silver screw from the 80mm metal standoff on the motherboard (A).
2. Align the small notch at the bottom edge of the M.2 card with the key in the connector.
3. Insert the bottom edge of the M.2 card into the connector (B).
4. Secure the card to the standoff with the small silver screw (C).
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
7
To install a 42mm M.2 SSD:
1. Remove the small silver screw from the metal standoff on the motherboard (A).
2. Move the standoff (B) from the 80mm position to the 42mm position (C).
3. Align the small notch at the bottom edge of the M.2 card with the key in the connector.
4. Insert the bottom edge of the M.2 card into the connector (D).
5. Secure the card to the standoff with the small silver screw (E).
Closing the Chassis
After all the components have been installed, close the Intel NUC chassis. Intel recommends this be done
by hand with a screwdriver to avoid over-tightening and possibly damaging the screws.
1. Place the top plate on the NUC chassis.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
8
2. Reattach the cable and secure the top plate with a screwdriver.
3. Place the top lid on the NUC and use the hex tool to tighten all the screws.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
9
Attaching and Using the VESA Bracket (Optional)
Follow these instructions to attach and use the VESA mount bracket:
1. Using the four small black screws that were included in the box, attach the VESA bracket to the
back of the monitor or TV.
2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.
User Guide for Intel® NUC 8
NUC8i7HNKQC and NUC8i7HVKVA
10
3. Slide the Intel NUC onto the VESA mount bracket.
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Intel Desktop Handbücher
Intel
Intel EES-5716 Bedienungsanleitung
Intel
Intel NUC11BT Bedienungsanleitung
Intel
Intel NUC Kit NUC7i7DNHE Bedienungsanleitung
Intel
Intel NUC8CY Kurzanleitung zur Einrichtung
Intel
Intel NUC 11 Performance Bedienungsanleitung
Intel
Intel SR2520SAXSR - Server System - 0 MB RAM Bedienungsanleitung
Intel
Intel NUC 12 Pro Bedienungsanleitung
Intel
Intel NUC8i3CYSM Bedienungsanleitung
Intel
Intel SRSH4 - Server Platform - 0 MB RAM Bedienungsanleitung
Intel
Intel NUC Kit DE3815TYKHE Bedienungsanleitung
Intel
Intel SR2600UR - Server System - 0 MB RAM Bedienungsanleitung
Intel
Intel NUC7i5DNKPC Bedienungsanleitung
Intel
Intel CareFusion DMS-SA1300-A1E Bedienungsanleitung
Intel
Intel NUC 12 Pro Kit NUC12WSHi3 Bedienungsanleitung
Intel
Intel NUC6CAYH Bedienungsanleitung
Intel
Intel NUC5i3RYH Bedienungsanleitung
Intel
Intel SC5650SCWS Bedienungsanleitung
Intel
Intel NUC7CJYSAL Bedienungsanleitung
Intel
Intel NUC7CJYS Kurzanleitung zur Einrichtung
Intel
Intel NUC Series Bedienungsanleitung
