Johnson Controls M300CJ Bedienungsanleitung

JC-460-000 4 I56-3750-001

Before InstallIng

This information is included as a quick reference installation guide. Refer to

the control panel installation manual for detailed system information. If the

modules will be installed in an existing operational system, inform the opera-

tor and local authority that the system will be temporarily out of service. Dis-

connect power to the control panel before installing the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

general DescrIptIon

M300CJ Supervised Control Modules are intended for use in intelligent, two-

wire systems, where the individual address of each module is selected us-

ing the built-in rotary switches. This module is used to switch an external

power supply, which can be a DC power supply or an audio amplifier (up

to 80 VRMS), to notification appliances. It also supervises the wiring to the

connected loads and reports their status to the panel as NORMAL, OPEN,

or SHORT CIRCUIT. The M300CJ has two pairs of output termination points

available for fault-tolerant wiring and a panel-controlled LED indicator. This

module can be used to replace a M510CJ module that has been configured for

supervised wiring operation.

compatIBIlIty requIrements

To ensure proper operation, this module shall be connected to a compatible

system control panel (list available from Johnson Controls).

mountIng

The M300CJ mounts directly to 4-inch square electrical boxes (see Figure 2A).

The box must have a minimum depth of 21⁄8inches. Surface mounted electri-

cal boxes (SMB500) are available from Johnson Controls.

WIrIng

NOTE: All wiring must conform to applicable local codes, ordinances, and

regulations. When using control modules in nonpower limited applications,

the CB500 Module Barrier must be used to meet UL requirements for the sepa-

ration of power-limited and nonpower-limited terminals and wiring. The bar-

rier must be inserted into a 4˝×4˝×21⁄8˝ junction box, and the control module

must be placed into the barrier and attached to the junction box (Figure 2A).

The power-limited wiring must be placed into the isolated quadrant of the

module barrier (Figure 2B).

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box, supplied by installer (see Figure 2A).

IMPORTANT: When using the M300CJ for fire fighter telephone applications,

remove Jumper (J1) and discard. The Jumper is located on the back as shown

in Figure 1B. The module does not provide ring back when used as a fire-

fighter telephone circuit.

specIfIcatIons

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 6.5 mA (LED on)

Average Operating Current: 375µA (LED Flashing, Group Poll); 350µA (LED Flashing, Direct Poll); 485µA Max. (LED Flashing, NAC Shorted)

Maximum NAC Line Loss: 4 VDC

External Supply Voltage (between Terminals T3 and T4)

Maximum (NAC): Regulated 24 VDC

Maximum (Speakers): 70.7Vrms, 50W

Drain on External Supply: 1.7 mA Max. using 24 VDC supply; 2.2 mA max. using 80Vrms supply

Maximum NAC Current Ratings: For Class B Wiring System, 3A; For Class A Wiring System, 2A

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% Non-condensing

Dimensions: 41⁄2˝ H x 4˝ W x 1

1⁄4˝ D (Mounts to a 4˝ square by 21⁄8˝ deep box.)

Accessories: SMB500 Electrical Box; CB500 Barrier

m300cJ superVIseD control moDule

JC-460-000 1 I56-3750-001

I56-3750-001

507 E. Michigan Street

Milwaukee, WI 53201

InstallatIon anD maIntenance InstructIons

fIgure 1a: fIgure 1B. Jumper locatIon:

C1059-00 C0910-00

fIgure 2a. moDule mountIng fIgure 2B:

WIth BarrIer:

C1070-00

JC-460-000 2 I56-3750-001

fIgure 3. typIcal notIfIcatIon applIance cIrcuIt confIguratIon, nfpa style y:

(+)

47K EOL

RESISTOR

ELR-47K

UL LISTED EOL

RELAY SHOWN

ENERGIZED

24 VDC COIL

EOLR-1

24 VDC CIRCUIT

DO NOT LOOP WIRE ON TERMINALS 10 & 11. BREAK WIRE

RUN TO PROVIDE SUPERVISION OF CONNECTIONS.

TO NEXT CONTROL MODULE OR

END-OF-LINE RELAY. ONE RELAY

REQUIRED FOR EACH CIRCUIT. SOME

CONTROL PANELS HAVE RELAY BUILT

IN AND DO NOT REQUIRE EXTERNAL

WIRING. REFER TO PANEL MANUAL.

24 VDC POWER SUPPLY

ISOLATED, REGULATED,

POWER LIMITED PER NFPA 70.

LISTED FOR FIRE PROTECTION

WITH BATTERY BACKUP.

MODULE POLARITIES ARE

SHOWN IN ALARM

CONNECT MODULES TO

LISTED COMPATIBLE CONTROL

PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

ALL WIRING SHOWN IS SUPERVISED

AND POWER LIMITED

CONTROL

MODULE

FROM PANEL

OR PREVIOUS

DEVICE

TO NEXT

DEVICE

*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.

(–) (–)

(–)

C0947-00

fIgure 4. typIcal fault tolerant notIfIcatIon applIance cIrcuIt confIguratIon, nfpa style Z:

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

ALL WIRING SHOWN IS SUPERVISED

AND POWER LIMITED

MODULE POLARITIES ARE

SHOWN IN ALARM

EOL RESISTOR

IS INTERNAL

AT TERMINALS

8 AND 9

UL LISTED EOL

RELAY SHOWN

ENERGIZED

24 VDC COIL

EOLR-1

TO NEXT CONTROL MODULE OR

END-OF-LINE RELAY. ONE RELAY

REQUIRED FOR EACH CIRCUIT. SOME

CONTROL PANELS HAVE RELAY BUILT

IN AND DO NOT REQUIRE EXTERNAL

WIRING. REFER TO PANEL MANUAL.

CONTROL

MODULE

TO NEXT

DEVICE

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

CONNECT MODULES TO LISTED

COMPATIBLE CONTROL

PANELS ONLY

FROM PANEL

OR PREVIOUS

DEVICE

24 VDC CIRCUIT

DO NOT LOOP WIRE ON TERMINALS 10

& 11. BREAK WIRE RUN TO PROVIDE

SUPERVISION OF CONNECTIONS.

24 VDC POWER SUPPLY

ISOLATED, REGULATED,

POWER LIMITED PER

NFPA 70. LISTED FOR

FIRE PROTECTION WITH

BATTERY BACKUP.

*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.

C0948-00

JC-460-000 3 I56-3750-001

fIgure 5. typIcal WIrIng for speaker superVIsIon anD sWItchIng, nfpa style y:

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

AUDIO CIRCUIT

DO NOT LOOP WIRE AROUND TERMINALS 10 & 11.

BREAK WIRE TO ENSURE

SUPERVISION OF CONNECTIONS.

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

ALL WIRING SHOWN IS

SUPERVISED AND POWER LIMITED

WIRES MUST BE SUPERVISED PER NFPA

CONNECT MODULES TO LISTED COMPATIBLE

CONTROL PANELS ONLY

FROM

PANEL OR

DEVICE

CONTROL

MODULE

47K EOL

RESISTOR

ELR-47K

SPEAKERS MUST BE LISTED FOR FIRE PROTECTION.

REFER TO THE RELAY CONTACT RATING TABLE FOR

MAXIMUM LOAD.

TO NEXT

DEVICE

MODULE POLARITIES ARE

SHOWN IN ALARM

TO NEXT CONTROL MODULE

LAST MODULE MUST RETURN

WIRES FOR SUPERVISION

SUPERVISION

AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM.

SEE NOTIFIER INSTALLATION MANUAL FOR DETAILED INFORMATION.

AUDIO AMPLIFIER, 70.7 Vrms MAX.

USE ONLY MODELS AA-30, AA100 OR

AA-120. AMPLIFIER MUST PROVIDE

WIRING SUPERVISION PER NFPA.

*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.

C0949-00

fIgure 6. typIcal fault tolerant WIrIng for speaker superVIsIon anD sWItchIng, nfpa style Z:

(+)

(–)

(+)

(–)

(+)

(–) (+)

(–)

(+)

(–)

(+)

ALL WIRING SHOWN IS SUPERVISED

AND POWER LIMITED

TO NEXT

DEVICE

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

WIRES MUST BE SUPERVISED PER NFPA

CONNECT MODULES TO LISTED COMPATIBLE

CONTROL PANELS ONLY

FROM

PANEL OR

DEVICE

CONTROL

MODULE

SPEAKERS MUST BE LISTED FOR

FIRE PROTECTION. REFER TO THE

RELAY CONTACT RATING TABLE FOR

MAXIMUM LOAD.

47K EOL RESISTOR

IS INTERNAL AT

TERMINALS 8 & 9

MODULE POLARITIES ARE SHOWN IN ALARM

TO NEXT CONTROL

MODULE LAST MODULE

MUST RETURN WIRES FOR

SUPERVISION

AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM.

SEE NOTIFIER INSTALLATION MANUAL FOR DETAILED INFORMATION.

AUDIO AMPLIFIER, 70.7 Vrms MAX.

USE ONLY MODELS AA-30, AA100 OR

AA-120. AMPLIFIER MUST PROVIDE

WIRING SUPERVISION PER NFPA.

AUDIO CIRCUIT

DO NOT LOOP WIRE AROUND TERMINALS 10 & 11.

BREAK WIRE TO ENSURE

SUPERVISION OF CONNECTIONS.

BYPASS CAPACITORS: 100µ

A2143-20 NONPOLARIZED

<10µA LEAKAGE

*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.

C0950-00

Andere Johnson Controls Steuereinheit Handbücher

Johnson Controls

Johnson Controls FX-PCX2721 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls GM 20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls Penn System 450 Series Bedienungsanleitung

Johnson Controls

Johnson Controls P352PN-2 Bedienungsanleitung

Johnson Controls

Johnson Controls MP8000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls Facility Explorer FX20 Bedienungsanleitung

Johnson Controls

Johnson Controls MS-IOU4710-0U Bedienungsanleitung

Johnson Controls

Johnson Controls VP101DBB Bedienungsanleitung

Johnson Controls

Johnson Controls G77 Series Service-Handbuch

Johnson Controls

Johnson Controls VP140 L Series Bedienungsanleitung

Johnson Controls

Johnson Controls Y20EBD Series Service-Handbuch

Johnson Controls

Johnson Controls Tyco TJPX0500003 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls C450CCN-2 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls IOM1711 Bedienungsanleitung

Johnson Controls

Johnson Controls VP140 Bedienungsanleitung

Johnson Controls

Johnson Controls MS-IOM2710-0U Bedienungsanleitung

Johnson Controls

Johnson Controls System 350 Y350R Service-Handbuch

Johnson Controls

Johnson Controls tyco AMD-1 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls GS-20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls H Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung