Kohler K-1842 Bedienungsanleitung

Installation Guide

Acrylic Shelving Unit

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-1842

1071450-2-C

Tools and Materials

Before You Begin

IMPORTANT! This product is for new construction or complete remodel (down to the studs) of tiled

showers only. Install this product to the studs only. Tile may be installed surrounding the product

when the installation is complete.

Please read these instructions carefully. This will help you to avoid costly mistakes.

Observe all local plumbing and building codes.

This installation is easiest when performed by two people.

Unpack and inspect the product for damage. If you ﬁnd any damage, do not install the product.

Report the speciﬁc problem to your dealer immediately. After inspection, return the product to the

carton until you are ready to install it.

The unit must be installed to adequately supported, plumb walls.

Make sure the installation area is clean and free of all debris. If remodeling, remove all ﬁnished wall

material to expose the stud wall/framing.

Consider the overall dimensions of the unit and location of the shower faucet(s) when planning the

unit’s location within the shower area.

Consult all applicable instructions for accessories and shower doors before installing.

Plus:

• Common Woodworking Tools

and Materials

• Common Tile Tools and

Materials

• Water Barrier Plastic Sheeting

• 2x4 or 2x6 Lumber

• Water Resistant Wall Material

and Fasteners

• Shims/Furring Strips

• 100% Silicone Sealant to Color

Match Grout

• Drop Cloth

Putty

Knife

Painters

Tape

100% Silicone

Sealant

Stapler

Safety

Glasses

1071450-2-C 2 Kohler Co.

1. Construct the Stud Framing

Install the drain and supply pipes according to local plumbing codes.

NOTICE: Plan the shower area around the desired placement of the unit. Ensure the placement of the

shelving unit will be free of obstructions (such as pipes or electrical boxes).

Build the shower area out of 2x4 or 2x6 lumber with the centers of the studs 16″(406 mm) apart.

Install the pipes, valves, and showerhead ﬁttings according to the plumbing manufacturer’s

instructions.

If applicable, install a watertight membrane to the ﬂoor.

Install the shower basin at this time. Refer to the shower basin manufacturer’s installation

instructions.

16" (406 mm)

Kohler Co. 3 1071450-2-C

2. Reinforce the Stud Pocket

IMPORTANT! Before securing the studs to the framing, conﬁrm that the studs are not warped.

Measure the height of the framing, and cut the studs to that measurement.

Install the studs to the outside of the framing with appropriate fasteners (not provided).

Verify the front surface of the studs are ﬂush. Plane the studs, if necessary.

Attach studs to outside

of determined location

with fasteners.

Stud Pocket

Side View

Confirm studs are

vertically level.

Fastener

1071450-2-C 4 Kohler Co.

3. Prepare the Site

Step 1

Wrap and staple water barrier plastic sheeting into the stud pocket.

Place and staple water barrier plastic sheeting over the remaining shower area.

If applicable, install the shower basin at this time.

Step 2

Determine the desired shelving unit height from the ﬁnished ﬂoor.

Verify that this height will not compromise the watertight membrane that may be present in the

ﬂoor when fasteners are installed to the bottom ﬂange of the unit. Adjust the height, if necessary.

Position and level the shelving unit on the studs at the desired height. Mark the corners of the

shelving unit on the studs, then set the unit aside.

Step 3

IMPORTANT! Select wall material that is water resistant and meets local building codes.

IMPORTANT! A ﬂush transition must exist between the wall material and the attachment ﬂange.

Verify the wall material equals the thickness of the attachment ﬂange, which is 1/4″(6 mm). This

will ensure a ﬂush transition. If a ﬂush transition does not exist, either the studs or attachment

ﬂange must be shimmed before installing the wall material.

Install wall material around the stud pocket, leaving an opening 62″(1575 mm) in height and

17-1/2″(445 mm) in width for the shelf unit.

Install wall material to the remainder of the shower area.

17-1/2"

(445 mm) Attachment

Flange

Flush

Transition

Install wall

material.

Install plastic sheeting.

Level, then

mark each

corner.

Level, then

mark each

corner.

Step 3

Step 2

Step 1

Kohler Co. 5 1071450-2-C

4. Secure the Unit

Position the unit over the stud pocket.

Thread a fastener (provided) 1″(25 mm) into the mounting hole at the top right corner.

Level the unit, then thread a fastener 1″(25 mm) through the mounting hole at the top left corner.

Alternating from side to side, as shown, partially thread fasteners through the remaining mounting

holes.

CAUTION: Risk of product damage. To avoid cracking the acrylic, do not overtighten the fasteners.

Fully tighten the fasteners, starting at the top and alternating from side to side.

Using 100% silicone sealant, ﬁll in the groove between the attachment ﬂange and the wall material

around the perimeter of the unit. If needed, use a putty knife to press the silicone sealant into the

gap. Wipe off any excess sealant.

Allow the sealant to cure before proceeding.

(25 mm)

019

Seal between gap.

Side View

1071450-2-C 6 Kohler Co.

5. Complete the Installation

Apply mesh tape between the unit and the wall material.

NOTICE: When planning the tile layout, the tile should conceal the installed fasteners on the unit

AND allow for a gap between the edge of the tile and the inner edge of the attachment ﬂange.

TIP: To ensure the ﬁrst row of tile is level, temporarily level and attach pieces of lumber to the bottom

portion of the wall material at a height less than a full tile. Remove the pieces of lumber once the adhesive

has set, then attach the remaining tile.

Plan the tile installation for the walls, then mark the plan on the wall material.

Attach the tile with tile adhesive or thin-set mortar designed for wet environments.

Allow the tile adhesive or thin-set mortar to cure.

Remove the pieces of lumber from the bottom portion of the wall material.

Apply grout to the tile, except for the expansion joints in the alcove.

Wipe the area with a damp sponge, allow the grout to set, then buff the tile with a soft cloth.

If desired, tape off the area adjacent to the groove where the tile and the acrylic unit meet. This will

help create a straight, uniform bead of silicone sealant.

Apply a bead of silicone sealant, that is color-matched to the grout, in the groove and any other

expansion joints.

Remove the tape once the sealant has cured.

Apply grout sealant to the tile.

Apply mesh tape.

Allow gap between unit and wall

material when installing tile.

Fill gap with

color-matched

silicone sealant.

Kohler Co. 7 1071450-2-C

Guide d’installation

Unité de rayonnage en acrylique

Outils et matériaux

Avant de commencer

IMPORTANT! Ce produit est destiné aux nouvelles constructions ou à un remodelage complet

(jusqu’aux montants) de douches avec carrelage uniquement. Installer ce produit sur les montants

seulement. Le carrelage peut être installé autour du produit lorsque l’installation est terminée.

Lire ces instructions avec la plus grande attention. Ceci permettra d’éviter des erreurs qui pourraient

être coûteuses.

Respecter tous les codes de plomberie et de bâtiment locaux.

Cette installation est exécutée le plus facilement par deux personnes.

Déballer et inspecter le produit pour détecter tout dommage. En cas de dommages, ne pas installer

ce produit. Informer immédiatement le distributeur du problème. Après avoir effectué une

inspection, remettre ce produit dans le carton d’emballage jusqu’à son installation.

L’unité doit être installée en étant supportée de manière adéquate, avec les murs d’aplomb.

S’assurer que la zone d’installation est propre et exempte de tous débris. En cas de remodelage,

retirer tout le matériau de mur ﬁni pour exposer le colombage/la charpente.

Tenir compte des dimensions globales de l’unité et de l’emplacement du ou des robinets de la

douche lors de la planiﬁcation de l’emplacement de l’unité dans la zone de la douche.

Consulter toutes les instructions applicables pour les accessoires et portes de douche avant de

procéder à l’installation.

Plus:

• Outils et matériaux de menuiserie

habituels

• Outils et matériaux pour carrelage

habituels

• Revêtement en plastique

imperméable à l'eau

• Bois 2x4 ou 2x6

• Dispositifs d'attache et matériau de

mur résistant à l'eau

• Cales/fourrures

• Mastic à la silicone à 100 % pour

apparier le mortier liquide en couleur

• Toile de protection

Couteau

à mastic

Ruban pour

peintre

Mastic à la

silicone à 100 %

Marteau

agrafeur

Lunettes

de sécurité

Kohler Co. Français-1 1071450-2-C

1. Construire l’ossature

Installer le drain et les tuyaux d’arrivée selon les codes de plomberie locaux.

AVIS: Planiﬁer la zone de la douche autour de l’emplacement souhaité de l’unité. S’assurer que

l’emplacement de l’unité de rayonnage sera exempt de toute obstruction (comme des tuyaux ou des

coffrets électriques).

Construire la zone de la douche avec du bois 2x4 ou 2x6, avec les montants centraux séparés de 16″

(406 mm).

Installer les tuyaux, les vannes, et les raccords de la pomme de douche conformément aux

instructions du fabricant du matériel de plomberie.

Si applicable, installer une membrane étanche à l’eau sur le plancher.

Installer le bac de la douche maintenant. Se reporter aux instructions d’installation du fabricant de

bac de douches.

16" (406 mm)

Kohler Co. Français-2 1071450-2-C

2. Renforcer le cadre porteur

IMPORTANT! Avant de ﬁxer les montants sur la charpente, vériﬁer que les montants ne sont pas

déformés.

Mesurer la hauteur de la charpente et couper les montants à cette mesure.

Installer les montants sur l’extérieur de la charpente avec des dispositifs d’attache appropriés (non

fournis).

Vériﬁer que la surface avant des montants est à ras. Planer les montants si nécessaire.

Attacher les montants à

l'extérieur de l'emplacement

déterminé avec des fixations.

Poche

de montant

Vue latérale

Confirmer la mise

à niveau verticale

des montants.

Fixation

1071450-2-C Français-3 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Inneneinrichtung Handbücher

Kohler

Kohler Top Art K-14041 Bedienungsanleitung

Kohler

Kohler K-26773-C05 Bedienungsanleitung

Kohler

Kohler SEQUOIA Bedienungsanleitung

Kohler

Kohler TOOBI K-15468T Bedienungsanleitung

Kohler

Kohler TRESHAM VANITY K-45980 Series Montageanleitung

Kohler

Kohler K-2461 Bedienungsanleitung

Kohler

Kohler K-2463 Bedienungsanleitung

Kohler

Kohler Natura 15457T Bedienungsanleitung

Kohler

Kohler Vanity K-2604 Montageanleitung

Kohler

Kohler K-2431 Montageanleitung

Kohler

Kohler NEW IPSWICH K-13987T-A Bedienungsanleitung

Kohler

Kohler Verdera K-99003-TL Bedienungsanleitung

Kohler

Kohler K-2451 Montageanleitung

Kohler

Kohler K-2684 Montageanleitung

Kohler

Kohler CL Series Bedienungsanleitung

Kohler

Kohler K-1082 Montageanleitung

Kohler

Kohler K-6334 Montageanleitung

Kohler

Kohler MING K-77127T Bedienungsanleitung

Kohler

Kohler VERDERA K-26385T Bedienungsanleitung

Kohler

Kohler K-76663T Bedienungsanleitung

Kohler

Kohler Escale 23264IN-NF Bedienungsanleitung

Kohler

Kohler PASTORIFE K-99074T Bedienungsanleitung

Kohler

Kohler FAMILY CARE K-31500T Bedienungsanleitung

Kohler

Kohler Englefield Valencia Elite Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung