Kohler K-7514 Bedienungsanleitung

Installation Guide

Touchless Bathroom Sink Faucet

Français, page “Français-1”

Español, página “Español-1”

K-7514, K-7515 K-7516, K-7517

K-7518, K-7519, K-45345 K-45344

1124217-2-E

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the water supply.

This faucet is for use on a single-hole bathroom sink.

For new installations, install the faucet and drain to the sink

before installing the sink.

The faucet shown in this guide may differ from your actual

product. The installation steps still apply.

In order for this faucet to function properly, install the faucet so

the sensor points directly toward the user.

The faucet is rated at6VDC1Wandisoperated by a Hybrid

Energy Cell (HEC) (provided).

1-1/4" to 1-1/2"

Hole Bit

1124217-2-E 2 Kohler Co.

1. Faucet Installation

Prepare the Site - AC and Hybrid Models

NOTE: Before drilling the mounting hole, use the following

provisions for proper placement:

A 1-1/4″(32 mm) minimum to 1-1/2″(38 mm) maximum

diameter mounting hole is required.

A minimum distance of 1-3/4″(44 mm) is required between the

back of the spout and the wall to allow access to the screw.

A 1-3/4″(44 mm) maximum distance is required between the

sink bowl edge and the base of the spout.

Install the Faucet

Determine the mounting hole location.

Drill a hole through the mounting surface according to the

surface manufacturer’s instructions.

Install the stud to the underside of the faucet.

Slide the O-ring over the ﬂexible hoses and stud, then seat the

O-ring in the groove on the underside of the spout.

Insert the spout with ﬂexible hoses and stud through the

mounting hole.

From under the sink, slide the rubber washer and bracket onto

the stud.

Without Escutcheon

Spout

Stud

O-Ring

Rubber Washer

Bracket Nut

Supply Hoses

Kohler Co. 3 1124217-2-E

Faucet Installation (cont.)

Thread the nut onto the stud to secure the faucet to the mounting

surface.

1124217-2-E 4 Kohler Co.

2. Supply Connections

Connect the Filter Assembly

Turn on the water and ﬂush water through the supply stops into

a bucket.

Turn off the water.

Remove the ﬁlter assemblies from the supply hoses. Then thread

a ﬁlter assembly onto each supply stop.

Connect the Supplies

For models with two hoses, thread the left supply hose to the

ﬁlter assembly on the hot supply stop and the right supply hose

to the ﬁlter assembly on the cold supply stop.

For models with one hose, thread the supply hose to the ﬁlter

assembly on the supply stop.

Tighten the connections with a small adjustable wrench.

Turn on the water and ﬂush the faucet by activating it.

NOTE: For optimum performance, clean your ﬁlter screens

periodically. Refer to the Maintenance Guide.

Flex Hose

Filter

Assembly

Supply

Stop

Housing

Adapter

Screen

Kohler Co. 5 1124217-2-E

3. Install the Power Supply

NOTE: Avoid the area in front of the sensor for 2 minutes after

connections are complete. The sensor will not function correctly if it

is triggered in the ﬁrst 2 minutes. Disconnect and reconnect the

power to reset the sensor.

Mount the Hybrid Energy Cell (HEC) under the counter using

two screws (not supplied).

Connect the HEC to the faucet wire.

Avoid the area in front of the sensor for 2 minutes.

Hybrid Models

Faucet Wire

Deck

Hybrid

Energy

Cell

1124217-2-E 6 Kohler Co.

4. Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. Scalding may result if

the temperature limit is set above 120°F (49°C).

NOTE: The water temperature does not need to be adjusted if the

water temperature is below 105°F (41°C).

NOTE: Use a thermometer rated for 120°F (49°C) or greater.

NOTE: When using a tempered water supply, install the

vandal-resistant plug button.

Adjust the Water Temperature Limit – Handle Installations

Turn on the water and adjust to full hot by turning the handle

toward the back of the faucet until it stops.

Determine the temperature using a thermometer. If the

temperature exceeds 105°F (41°C), complete the following steps.

NOTICE: Do not rotate the handle when removing the screw.

Using the 2.5 mm hex wrench provided, remove and retain the

handle screw.

Remove and retain the handle with the spring washer.

Handle

Screw

Vandal-Resistant

Plug Button

Spring

Washer

Kohler Co. 7 1124217-2-E

Optional Temperature Limiting Adjustment (cont.)

Insert the handle at the desired maximum temperature. If the

handle is inserted horizontally: This is the maximum hot

temperature, where the water will be the same temperature as the

water from the hot water supply. If the handle is inserted

vertically (shown): This is the maximum cold temperature, where

the water will be the same temperature as the water from the

cold water supply.

NOTICE: Do not rotate the handle when reinstalling the screw.

Reinstall the spring washer into the handle, then attach the

handle to the faucet.

Secure the handle to the faucet with the screw.

Adjust the Water Temperature Limit – Vandal-Resistant Installations

NOTE: If you install the vandal-resistant plug button, save the

handle to adjust the water temperature at a later date.

Using the handle, adjust the water to the desired temperature.

Using the 2.5 mm hex wrench provided, remove and retain the

screw, spring washer, and handle.

Position the vandal-resistant plug button and ﬁrmly press into

place.

1124217-2-E 8 Kohler Co.

5. Installation Checkout

Using the key provided, remove the aerator from the spout.

If applicable, uncover the drain.

Turn on the water supply and check for leaks. Adjust as needed.

Allow the water to run through the spout for about 1 minute to

remove any debris. Check for leaks and adjust as needed.

Temporarily cover the sensors on the faucet or close the water

supplies.

Using the key provided, reinstall the aerator to the spout.

Uncover the sensors on the faucet or turn on the water supplies.

Troubleshooting

Symptoms Probable Causes Recommended Action

1. No water ﬂow. A. Filter is plugged. A. Clean or replace the

ﬁlter.

B. Sensor eyes are

dirty. B. Wipe the sensor eyes

with a damp soft cloth.

Wipe dry with a dry soft

cloth.

Aerator

Key

Kohler Co. 9 1124217-2-E

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

C. Water not turned

on. C. Verify that the water

supply is turned on and

that pressure is at least 20

psi (137 kPa).

D. Incorrect

installation. D. Verify that the faucet is

mounted as instructed in

the installation guide.

Ensure that the sensor eyes

are above the rim of the

sink. Refer to the

installation instructions.

E. The aerator is

plugged. E. Remove and clean the

aerator. For

calcium/mineral deposits,

soak the plastic insert in a

50:50 mix of water and

vinegar. Soak only the

plastic insert.

F. Sensor eyes are

scratched. F. Replace the sensor

assembly.

G. A ﬂex hose is

kinked. G. Check the ﬂex hoses to

make certain they are not

kinked. If a ﬂex hose is

kinked, disconnect it,

straighten, and reconnect.

H. Hybrid Energy

Cell (HEC) has just

been replaced.

H. Wait 2 minutes after

replacing the HEC as the

sensor cycles through the

automatic sensing distance.

I. HEC life expired. I. Replace the HEC.

J. Bleed hole in

diaphragm is

plugged or debris

exists on the seal.

J. Clean or replace the

diaphragm.

K. Solenoid is not

working. K. Order a new solenoid

service kit.

2. Low ﬂow. A. Filter is plugged. A. Clean or replace the

ﬁlter.

B. Supply pressure

is low. B. Check incoming water

pressure. Pressure should

be at least 20 psi (137 kPa).

1124217-2-E 10 Kohler Co.

Andere Handbücher für K-7514

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Glenbury Quiet-Close K-4733 Bedienungsanleitung

Kohler

Kohler K-14281 Bedienungsanleitung

Kohler

Kohler 12969T-B Bedienungsanleitung

Kohler

Kohler Loure K-15285 Montageanleitung

Kohler

Kohler 8002A Bedienungsanleitung

Kohler

Kohler STRAYT 37331T Bedienungsanleitung

Kohler

Kohler K-352 Bedienungsanleitung

Kohler

Kohler 32E Bedienungsanleitung

Kohler

Kohler K-45471X Montageanleitung

Kohler

Kohler 77984T-4MU Bedienungsanleitung

Kohler

Kohler K-6352 Bedienungsanleitung

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler K-1257P Kurzanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.8 kW Bedienungsanleitung

Kohler

Kohler VINTAGE K-7158 Bedienungsanleitung

Kohler

Kohler K-15003 Bedienungsanleitung

Kohler

Kohler K-596D Bedienungsanleitung

Kohler

Kohler 5EKD Bedienungsanleitung

Kohler

Kohler K-2953 Montageanleitung

Kohler

Kohler 18492-CP Montageanleitung

Kohler

Kohler K-19909-4 Montageanleitung

Kohler

Kohler K-9677 Montageanleitung

Kohler

Kohler K-14402 Montageanleitung

Kohler

Kohler STEWARD ECO Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung