Kohler 8022A Bedienungsanleitung

11063864-AN2-E 17/02/12

IMPORTANT

INSTALLER: THIS MANUAL IS THE PROPERTY OF THE

CUSTOMER AND MUST BE RETAINED WITH THE PRODUCT

FOR MAINTENANCE AND OPERATIONAL PURPOSES.

Installation and User Guide

Watertile Showerhead

MODEL NUMBERS

Important! Please quote the above model number(s) when ordering spares

8022A, 8023A

1063864-AN2-E 17/02/12

SPECIFICATION

Pressures

For multiple outlets an operating pressure of 3.0 bar or greater is

recommended to ensure optimum performance.

Plumbing Connections

(Hot) and Cold (C) inlets must be connected to the

correct inlet supplies.

Building in Depth

Minimum building in depth is 79 mm. It is recommended that

a minimum stud wall cavity of 100 mm is provided to ease installation.

DIMENSIONS

8033A 8022A

121

127

121

127

137

121

45°

All information is based on the latest product information available at the time

of publication. Kohler Co. reserves the right to make changes in product

characteristics, packaging, or availability at any time without notice.

Please leave these instructions for the consumer.

NOTES:

1. Flush the water supply pipes thoroughly to remove any debris.

2. An in line water filter must be used with this product.

3. Inspect the supply pipes for damage. Replace as necessary.

4. Observe local plumbing codes.

5. The recommended working pressure for the shower head is 150KPa to

500KPa. If the pressure exceeds 500KPa a pressure reducer is required.

6. Maximum water and environmental temperature for the shower head is

60C. Note: If a heater is present, make sure to keep it away from the shower

head as otherwise the environmental temperature may exceed 60C.

7. All installations should comply with the relevant requirements of AS/NZS

3500 and AS/NZS 6400.

BEFORE YOU BEGIN

31063864-AN2-E 17/02/12

Install the Pipe and Elbow

1. Install the water supply pipes.

2. Install the wall mount elbow to the end

of the water supply pipe at the shower

head installation location.

Note! The wall mount elbow, wall plugs

and ﬁxing screws are not supplied with

the product. The installer should use an

appropriate wall ﬁxing arrangement to

suit the wall type or surface.

3. Mark the position of the Wall Mount Elbow. For solid walls

drill the wall Mount Elbow holes with a 7mm diameter drill and

insert the wall plugs (Supplied). For other types of wall structure

alternative fixing may be required (Not supplied)

4. Fix the Wall Mount Elbow to a solid wall or to a frame mounting using the

fixing Screws supplied.

5. Finish the wall leaving a Ø76mm cutout.

6. Temporarily install the Elbow to the nipple. Do not use any sealant.

7. Make sure that the nipple extends 29mm from the finished wall.

If necessary cut the long leg of the nipple to the required length

8. Apply thread sealant to the long leg of the Nipple and install it into the Elbow

9. Run water through the system to ﬂush out any dirt or debris.

Elbow

Finished

Wall

Nipple

29 mm

41 mm Max.

Cutout

Ø 76 mm

G ½”

IONINSTALLAT

Before you Begin

1. Turn off the water supply.

2. Make sure that the Watertile showerhead is installed by a competent

installer.

3. Before installation carefully inspect the new ﬁxture for any signs of damage.

4. Kohler Co. reserves the right to make revisions in the design of products without

notice.

1063864-AN2-E 17/02/12

Install the Watertile Showerhead

Prepare the Housing:

1. Position the housing so that the back of

the leak shield is facing you.

2. Apply a bead of silicone sealant in

the groove around the outside of the

housing. Do not apply silicone sealant

in or near the weep hole.

3. Allow the silicone sealant to cure.

Install the Components:

1. Position the housing with the sealant

side towards the finished wall and

the narrow end of the housing facing

down.

2. Position the so that the nipple is through

the centre and press ﬁrmly against the

ﬁnished wall.

3. Thread the adaptor onto the nipple.

Install the Waterway:

1. Press the waterway into place over the

adaptor.

2. Secure the waterway to the adaptor

with the screw provided. The waterway

will be secure once the housing is

completely seated against the wall and

does not turn or move.

Finished Wall

Housing

Waterway

Adaptor

Double Ribs Slot

Apply Silicone Sealant

Weep Hole

Leak Shield

51063864-AN2-E 17/02/12

Finish the Installation

1. With the ribs of the sprayhead facing up,

attach the sprayhead to the waterway.

2. Using a 3/16” hexagonal key, secure

the sprayhead to the waterway with the

2 securing screws (supplied). Do not

overtighten.

3. Check the sprayhead for upward and

downward movement and that it sits

squarely within the housing.

4. Place the nozzle membrane over the

sprayhead

Note! For optimum performance make

sure that the membrane is applied

evenly.

5. Tilt the sprayhead downward so that

the ribs on top of the sprayhead are

exposed.

6. Insert the grooves of the sprayface over

the ribs of the sprayhead.

7. Press the sprayface down to cover the

sprayhead, as illustrated.

8. Tilt the sprayhead upwards to expose

the setscrew holes on the bottom of the

sprayhead.

Important! The setscrews must be ﬂush

with the edge of the sprayface frame. If

the setscrews protrude outside of the

sprayface frame product damage will

occur.

9. Using a 7/64” hexagonal key, turn the

setscrews anti-clockwise until they are

ﬂush with the edge of the sprayface

frame.

Hex Screws

Waterway

Sprayhead

Groove

Ribs

Nozzle

Membrane

Finished Wall

Ribs

Sprayface

Setscrews

Attach the Sprayhead

Attach the Sprayface

1063864-AN2-E 17/02/12

SPARE PARTS

** Finish/colour code must be speciﬁed when ordering.

1056030

Elbow

1043560**

Housing

1036043

Shield

1055233

Adapter

1045773

Base (includes

clamps)

1048768

Sprayhead

1039746

Nozzle

1036041**

Spray Face

1036044

Clamp

1041575

Nozzle 1041573**

Spray Face

1036044

Clamp

1045769

Sprayhead

1079599

Grommet

71063864-AN2-E 17/02/12

CARE AND CLEANING

Like anything of lasting quality, Kohler tapware and fittings require a certain amount of

periodic care to preserve their lustrous finish. Clean your new Kohler tapware and fittings

with a mild soap, rinse thoroughly with warm water and dry with a clean, soft cloth.

The ideal cleaning technique is to always blot dry any water from metal surfaces.

Allowing water to evaporate on metal will form water deposits. It is important to use a

dabbing action to dry metal, not an abrasive or rubbing action.

Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, or chemicals

that can damage the finish. By taking the time to dry your tapware often, soap and water

deposits can be prevented.

Failure to comply with these cleaning instructions may void Kohler’s warranty obligations.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler rada Exact-3 B Bedienungsanleitung

Kohler

Kohler MOXIE 99107T Bedienungsanleitung

Kohler

Kohler Mira Jump 7.5 Bedienungsanleitung

Kohler

Kohler Finial K-20012T-CP Bedienungsanleitung

Kohler

Kohler FLIGHT NEUS E62C70-00 Bedienungsanleitung

Kohler

Kohler 8030A Bedienungsanleitung

Kohler

Kohler 1202901-5-B Montageanleitung

Kohler

Kohler K-352 Montageanleitung

Kohler

Kohler K-9025 Bedienungsanleitung

Kohler

Kohler Triton K-T7019 Bedienungsanleitung

Kohler

Kohler BADRON K-5487T-B Bedienungsanleitung

Kohler

Kohler K-19321T Bedienungsanleitung

Kohler

Kohler K-7702 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Kohler

Kohler K-11608 Bedienungsanleitung

Kohler

Kohler K-77681 Series Bedienungsanleitung

Kohler

Kohler Mira Sport Thermostatic 9.8kW 1.1746.006 Bedienungsanleitung

Kohler

Kohler K-7779 Montageanleitung

Kohler

Kohler K-14663 Montageanleitung

Kohler

Kohler Clearflo K-7147 Montageanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.0 kW Bedienungsanleitung

Kohler

Kohler K-77364M-AS Bedienungsanleitung

Kohler

Kohler GP30420 Handbuch

Kohler

Kohler K-484 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Bedienungsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Fortis

Fortis MILANO 78211JS Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Moen

Moen 5922 Series Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung