Kohler K-3900 Bedienungsanleitung

Installation Guide

Toilet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-3900

1132336-2-D

Important Information

NOTE: This product is designed for installation with the electrical and water supplies located through

either the wall or the ﬂoor.

Grounding Instructions

•This product should be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electric shock by providing an escape wire for the electric current. This product is equipped

with a cord having a grounding wire with a grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

WARNING: Risk of electric shock. Improper use of the grounding plug can result in a risk of

electric shock.

•If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either

ﬂat blade terminal. The wire with insulation having an outer surface that is green with or without

yellow stripes is the grounding wire.

•Check with a qualiﬁed electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the product is properly grounded.

•This product is factory equipped with a speciﬁc electric cord and plug to permit connection to a

proper electric circuit. Make sure that the product is connected to an outlet having the same

conﬁguration as the plug. No adapter should be used with this product. Do not modify the plug

provided — if it will not ﬁt the outlet, have the proper outlet installed by a qualiﬁed electrician. If

the product must be reconnected for use on a different type of electric circuit, the connection should

be made by qualiﬁed service personnel.

Tools and Materials

Drill with Assorted Bits

Assorted

Screwdrivers Wax Ring

Adjustable Wrench

Plus:

• Protective Material

• Tape

• Water Hammer Arrestor

Offset Screwdriver

Wall Plate

1132336-2-D 2 Kohler Co.

Before You Begin

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of electric shock. For plug-in installations/wall-mounted electrical supply:

Connect only to a properly-grounded, grounding-type receptacle which is protected by a 120 V, 15

A minimum, 60 Hz Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Do

not remove the grounding pin or use a grounding adapter.

CAUTION: Risk of personal injury. This toilet weighs approximately 100 lbs (45 kg). Lift the toilet

with two people, employing proper lifting technique.

CAUTION: Risk of hazardous gases. If a new toilet is not installed immediately, temporarily place

a rag in the ﬂoor ﬂange opening.

CAUTION: Risk of property damage. This toilet is not intended to be installed in buildings where

temperatures will drop below 32°F (0°C). The design of the toilet makes it difficult to remove all

water from the tank. If frozen, the water could damage the tank resulting in leaking.

NOTICE: Follow all local plumbing and electrical codes.

IMPORTANT! This product requires a minimum static pressure of 30 psi (206.8 kPa) for satisfactory rim

wash performance.

Carefully inspect the new toilet for damage.

Consult the online users guide at kohler.com for more information.

Kohler Co. reserves the right to make revisions in the design of products without notice, as speciﬁed

in the Price Book.

Conﬁrm all parts below are included before beginning the installation.

2 Bushings

2 Caps

2 #10 x 1-1/2"

Screws

Supply Hose Clip

2 Mounting Blocks

(4) 5/16" x 2-1/2" Lag Bolts

Remote Control

Docking

Station

(4) 5/16" Lag Bolt Anchors

Back Cover

(Through-the-Floor

Installations)

Parts Bag Contents

Other Parts

Kohler Co. 3 1132336-2-D

Before You Begin (cont.)

Parts Bag Contents

(4) 5/16″x 2-1/2″Lag Bolts

(4) 5/16″Lag Bolt Anchors

2 Mounting Blocks

2 Plastic Caps

2 #10 x 1-1/2″Screws

2 Bushings

Remote Control Box Contents

Docking Station

Remote Control

Docking Station Power Cord (not shown)

FM External Antenna (not shown)

AUX In Audio Cord (not shown)

Other Parts

Back Cover (used in through-the-ﬂoor installations)

Supply Hose

Clip

1132336-2-D 4 Kohler Co.

Roughing-in - Wall Mount Electrical and Water Supply

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of electrical shock. For plug-in installations/wall-mounted electrical supply:

Connect only to a properly-grounded, grounding-type receptacle which is protected by a

Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Do not remove the

grounding pin or use a grounding adapter.

NOTICE: The locations for the supply shut-off, electrical outlet, and docking station cord are suggested

locations. Make sure all installations adhere to applicable codes and standards.

IMPORTANT! Locating the supply stop behind the toilet will make it difficult to remove the back panel.

It may be necessary to remove the toilet to service items behind the back panel if the supply stop extends

more than 3″(76 mm) from the wall.

IMPORTANT! Do not install any items behind the toilet that will interfere with the cover when it is

raised. All decorative items should be at least 37″(940 mm) high to allow clearance for the cover.

The remote docking station is equipped with a 15’ (4.5 m) power cord. The station mounting

location shown for the docking station is ADA compliant.

The supplied power cord is 56″(1422 mm) in length. Install the GFCI or RCD protected outlet

within 56″(1422 mm) of the toilet location.

The toilet is equipped with a motion sensor to automatically open the cover when movement is

sensed. This sensor has a maximum range of 51-1/2″(1300 mm). Sensitivity can be adjusted or

turned off using the User Interface.

The toilet is equipped with a sensor to automatically open the seat when the light is interrupted.

The sensor is located on the right side of the toilet. This sensor has a maximum range of 8″(203

mm). Keep this area free of obstructions.

Optional

Supply,

1/2" OD

Compression

Outlet Thread

Front of Bowl

Finished

Wall

L Of Outlet

Docking Station

Outlet

1/2" OD

Compression

Outlet Thread

Optional Supply

1/2" OD Compression

Outlet Thread

25-3/4"

(654 mm)

Ø 2-5/8"

(67 mm)

14-1/2"

(368 mm)

25-1/4"

(641 mm)

13-5/8"

(346 mm)

10-13/16" (275 mm)

3-3/4" (95 mm),

3-9/16" (90 mm) Min

29-1/2" (749 mm)

12"

(305 mm)

12" (305 mm)

15-5/8"

(397 mm)

2-1/4"

(57 mm)

1-3/4"

(44 mm),

1-1/2"

(38 mm)

Min

36-1/4"

(921 mm)

Power Cord

Reaches

56" (1422 mm)

4-1/16"

(104 mm)

5-15/16"

(151 mm)

41" (1041 mm) -

66" (1676 mm)

38" (965 mm) - 66" (1676 mm)

4-3/4" (121 mm)

2" (51 mm)

17-7/8"

(454 mm)

(152 mm)

8" (203 mm)

Kohler Co. 5 1132336-2-D

Roughing-in - Wall Mount Electrical and Water Supply (cont.)

1/2″OD compression supply stop outlet is required unless an adapter is used.

Installation of a water hammer arrestor is required.

1132336-2-D 6 Kohler Co.

Roughing-in - Through-the-Floor Water and Electrical

NOTICE: The locations for the supply shut-off, electrical outlet, and docking station cord are suggested

locations. Make sure all installations adhere to applicable codes and standards.

IMPORTANT! Do not install any items behind the toilet that will interfere with the seat when it is raised.

All decorative items should be at least 37″(940 mm) high to allow clearance for the seat.

The remote docking station is equipped with a 15’ (4.5 m) power cord. The station mounting

location shown for the docking station is ADA compliant.

The supplied power cord is 56″(1422 mm) in length.

The toilet is equipped with a motion sensor to automatically open the cover when movement is

sensed. This sensor has a maximum range of 51-1/2″(1300 mm). Sensitivity can be adjusted using

the User Interface.

The toilet is equipped with a seat actuator sensor, located on the right side of the toilet. This sensor

has a maximum range of 8″(203 mm). Keep this area free of obstructions.

1/2″OD compression supply stop outlet is required unless an adapter is used.

Installation of a water hammer arrestor is required.

Front of Bowl

25-3/4" (654 mm)

Finished Wall

Docking Station

Ø 1-1/2" (38 mm)

Water Supply Hole

Ø 1-1/4" (32 mm)

Power Supply Hole

Ø 2-5/8"

(67 mm)

14-1/2"

(368 mm)

25-1/4"

(641 mm)

10-13/16" (275 mm)

3-3/4" (95 mm),

3-9/16" (90 mm) Min

29-1/2" (749 mm)

12"

(305 mm)

12"

(305 mm)

15-5/8"

(397 mm)

2-1/4"

(57 mm)

1-3/4"

(44 mm),

1-1/2"

(38 mm)

Min

36-1/4"

(921 mm)

4-1/16"

(104 mm)

5-15/16"

(151 mm)

38" (965 mm) - 66" (1676 mm)

4-3/4" (121 mm)

17-7/8"

(454 mm)

41" (1041 mm) -

66" (1676 mm)

L Of Outlet

13-5/8"

(346 mm)

Kohler Co. 7 1132336-2-D

Prepare the Site

WARNING: Risk of electric shock. Disconnect power before installation or servicing.

WARNING: Risk of electric shock. Connect only to a properly-grounded, grounding-type

receptacle which is protected by a 120 V, 15 A minimum, 60 Hz Ground-Fault Circuit-Interrupter

(GFCI) or Residual Current Device (RCD). Do not remove the grounding pin or use a grounding

adapter.

WARNING: Risk of electrical shock. For hardwire installations/through-ﬂoor electrical supply:

Connect only to a properly-grounded, dedicated circuit protected by an Class A Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD).

NOTE: The electrical outlet and water supply may also be located behind the toilet. If it is located behind

the toilet, the water supply stop must extend no more than 3″(76 mm) beyond the ﬁnished wall. If located

behind the toilet, the supply stop must be a model that connects at a 90° angle. The handle should be

easily accessible.

NOTE: Locating the supply stop behind the toilet will make it difficult to remove the back panel. It may

be necessary to remove the toilet to service items behind the back panel if the supply stop extends more

than 3″(76 mm) from the wall.

Install the Dock Power Cord

If the ﬁnished wall has not been installed, route the docking station power cord if the cord will be

routed through the wall.

If the ﬁnished wall is installed, drill a 3/8″(10 mm) hole in the wall behind the toilet location for

the docking station power cord.

If the docking station cord is routed through the wall, route the power cord to the docking station

location from the toilet end. Route it through a wall plate or route the cord on the wall externally.

(152 mm)

12" (305 mm) From

Finished Wall

Recommended,

11-3/4" (298 mm) Min

Supply Stop

Floor Flange

GFCI/RCD

Protected

Receptacle

3" (76 mm) Max

When Located

Behind Toilet

(102 mm)

Dock

Power

Cord

2" (51 mm)

Ø 1-1/2" (38 mm)

Water Supply Hole

(for through-the-floor

installations only)

Ø 1-1/4" (32 mm)

Power Supply Hole

(for through-the-foor

installations only)

2-5/8"

(67 mm)

1-5/8"

(41 mm)

8" (203 mm)

1132336-2-D 8 Kohler Co.

Prepare the Site (cont.)

Install the Water Supply

IMPORTANT! When installing the supply hose, connect it to the toilet ﬁrst, then the supply stop.

NOTE: The supplied water supply hose is 18″(457 mm) in length. The supplied hose must be used for

this installation.

Install the water supply and supply stop.

Install a water hammer arrestor to the supply stop or water supply line.

Flush the water supply line into a pail or other container to remove all debris.

Install the Electrical Service

NOTE: The suppled power cord is 56″(1422 mm) in length.

Locate a dedicated 120 V, 15 A minimum, 60 Hz grounding-type receptacle, protected by a GFCI or

RCD, within 56″(1422 mm) of the back of the toilet.

Install External Speaker Wires (optional)

If external speakers will be used, install the speaker wires at this time.

Kohler Co. 9 1132336-2-D

1. Install the Remote Dock

NOTE: The docking station comes with a 15’ (4.6 m) cord. Locate the docking station to allow the docking

cord to reach the toilet.

Unpack the box containing the remote control components.

Remove the remote control from the dock and set aside.

Remove the small screw on the bottom of the docking station.

Carefully remove the cover plate by gently prying the sides of the cover plate out until they

disconnect from the dock.

Carefully disconnect the cover plate plug.

Tape the screw to the cover plate and set it aside.

NOTE: When the docking station cord is routed externally through the wall, it may be easier to use the

back cord opening. When the cord is routed externally along the face of the wall, use the bottom cord

opening.

For installations using the back cord opening, route the power cord through the back cord opening.

For installations using the bottom cord opening, route the power cord through the bottom cord

opening.

Position the docking station in the installation position and mark the screw locations using the dock

as a template.

Drill appropriate size mounting holes at the screw mounting locations. The size of the hole will

depend on the need for wall anchors, wall material, and installation requirements.

Loosen each of the ﬁve small screws located where the wires will be connected.

Run the power cord into the docking station.

Holes

Red

Blue

White

Black

Orange

Screw

Connector

Harness

Docking

Cord

Back Cord

Opening

Bottom Cord

Opening

Back Cord

Opening

Disconnect.

Front Plate

Rear

Plate

1132336-2-D 10 Kohler Co.

Andere Handbücher für K-3900

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-6814-3 Montageanleitung

Kohler

Kohler ESCALE K-19611T Bedienungsanleitung

Kohler

Kohler July 16027 Bedienungsanleitung

Kohler

Kohler K-15171 Montageanleitung

Kohler

Kohler K-7163 Montageanleitung

Kohler

Kohler PINOIR K-2015 Montageanleitung

Kohler

Kohler K-5664 Montageanleitung

Kohler

Kohler PURIST 10129T-4 Bedienungsanleitung

Kohler

Kohler MINIMA K-45805T Bedienungsanleitung

Kohler

Kohler K-4350 Series Montageanleitung

Kohler

Kohler BRAZN K-702242T Bedienungsanleitung

Kohler

Kohler K-16230 Bedienungsanleitung

Kohler

Kohler 77980T-4 Bedienungsanleitung

Kohler

Kohler Oblo K-124B16-SANA-CP Bedienungsanleitung

Kohler

Kohler K-12177 Bedienungsanleitung

Kohler

Kohler K-7374 Montageanleitung

Kohler

Kohler GEOG K-21727T-PF040-Q73 Bedienungsanleitung

Kohler

Kohler K-T72770 Montageanleitung

Kohler

Kohler K-7223 Montageanleitung

Kohler

Kohler KT6908 Bedienungsanleitung

Kohler

Kohler K-T15806 Bedienungsanleitung

Kohler

Kohler K-R99252X-4CD Montageanleitung

Kohler

Kohler K-9018 Montageanleitung

Kohler

Kohler K-10280 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung