Kohler K-13462 Bedienungsanleitung

Installation Guide

Touchless Bathroom Sink Faucet

Français, page “Français-1”

Español, página “Español-1”

K-13462, K-13463 K-13468, K-13469

K-13474, K-13475

1124215-2-B

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

This faucet is for use on a single-hole bathroom sink.

For new installations, install the faucet and drain to the sink

before installing the sink.

The faucet shown in this guide may differ from your actual

product. The installation steps still apply.

In order for this faucet to function properly, install the faucet so

the sensor points directly toward the user.

The faucet is rated at6VDC1Wandisoperated by an external

AC power supply (not supplied).

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

1-1/4" to 1-1/2"

Hole Bit

1124215-2-B 2 Kohler Co.

1. Faucet Installation

Prepare the Site

NOTE: Before drilling the mounting hole, use the following

provisions for proper placement: (1) A 1-1/4″(32 mm) minimum to

1-1/2″(38 mm) maximum diameter mounting hole is required. (2) A

minimum distance of 1-3/4″(44 mm) is required between the back

of the spout and the wall to allow access to the screw. (3) A 1-1/8″

(29 mm) maximum distance is required between the sink bowl edge

and the base of the spout.

Determine the mounting hole location.

Drill a hole through the mounting surface according to the

surface manufacturer’s instructions.

Install the Faucet

Install the stud to the underside of the faucet.

Slide the gasket over the ﬂexible hoses and stud, then seat the

gasket in the groove on the underside of the spout.

Insert the spout with ﬂexible hoses and stud through the

mounting hole.

From under the sink, slide the rubber washer and bracket onto

the stud.

Thread the nut onto the stud to secure the faucet to the mounting

surface.

Without Escutcheon

Spout

Stud

Gasket

Rubber Washer

Bracket Nut

Supply Hoses

Kohler Co. 3 1124215-2-B

2. Supply Connections

Connect the Filter Assembly

Turn on the water and ﬂush water through the supply stops into

a bucket.

Turn off the water.

Remove the ﬁlter assemblies from supply hoses. Then thread a

ﬁlter assembly onto each supply stop.

Connect the Supplies

Connect the left supply hose to the ﬁlter assembly on the hot

supply stop.

Connect the right supply hose to the ﬁlter assembly on the cold

supply stop.

Tighten the connections with a small adjustable wrench.

Turn on the water and ﬂush the faucet by activating it.

NOTE: For optimum performance, clean your ﬁlter screens

periodically. Refer to the Maintenance Guide.

Flex Hose

Filter

Assembly

Supply

Stop

Housing

Adapter

Screen

1124215-2-B 4 Kohler Co.

3. Install the AC Supply

Single Faucet Installations

Connect the faucet wire to the AC supply.

Plug the AC supply into the wall outlet.

Secure the excess wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the two minute learning cycle or the faucet may not

function properly.

Allow two minutes for the sensor to cycle through the automatic

sensing distance.

AC Supply

Plug AC supply

into wall outlet.

Faucet Wire

Secure any excess wire

under the counter.

Kohler Co. 5 1124215-2-B

4. Install AC Multi-Output Supply

Multiple Faucet Installations

Mount the AC supply under the counter using two (not supplied)

screws. Orient as shown.

Remove the cover.

Connect the faucet wire to the faucet.

If needed, cut and strip the AC supply wires to length.

Connect the stripped ends to the bottom terminal block (TB2) in

the supply box.

NOTE: If a hard wired installation is required, go to the next

installation section.

Plug the AC supply into the wall outlet.

Secure any excess wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the two minute learning cycle or the faucet may not

function properly.

Allow two minutes for the sensor to cycle through the automatic

sensing distance.

AC Gang

Supply

Black Red

AC Supply

1124215-2-B 6 Kohler Co.

5. Hard Wire Installation

WARNING: Risk of electrical shock. Make sure the power

has been disconnected before performing the following

procedures.

Loosen the terminal block screws and remove the wires from the

top terminal block.

Loosen the outside nut of the strain relief and remove the power

cord.

Put the supply wires through the strain relief and connect to the

top terminal block.

NOTE: If a hard wired installation is required, the strain relief may

need to be replaced depending on wire used.

Tighten the nut on the strain relief.

Replace the cover, and install and tighten the ﬁve screws.

Turn on the AC supply power.

Secure any extra wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the two minute learning cycle or the faucet may not

function properly.

Allow two minutes for the sensor to cycle through the automatic

sensing distance.

Secure any excess

wire under counter.

Kohler Co. 7 1124215-2-B

6. Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. Scalding may result if

the temperature limit is not properly set.

NOTE: The water temperature does not need to be adjusted if the

water temperature is below 105°F (41°C).

NOTE: Use a thermometer rated for 120°F (49°C) or greater.

NOTE: When using a tempered water supply, install the

vandal-resistant plug button.

Adjust the Water Temperature Limit – Handle Installations

Turn on the water and adjust to full hot by turning the handle

toward the back of the faucet until it stops.

Determine the temperature using a thermometer. If the

temperature exceeds 105°F (41°C), complete the following steps.

NOTICE: Do not rotate the handle when removing the screw.

Using the 2.5 mm hex wrench provided, remove and retain the

handle screw.

Remove and retain the handle with the spring washer.

Handle

Screw

Vandal-Resistant

Plug Button

Spring

Washer

1124215-2-B 8 Kohler Co.

Optional Temperature Limiting Adjustment (cont.)

Insert the handle at the desired maximum temperature. If the

handle is inserted horizontally: This is the maximum hot

temperature, where the water will be the same temperature as the

water from the hot water supply. If the handle is inserted

vertically (shown): This is the maximum cold temperature, where

the water will be the same temperature as the water from the

cold water supply.

NOTICE: Do not rotate the handle when reinstalling the screw.

Reinstall the spring washer into the handle, then attach the

handle to the faucet.

Secure the handle to the faucet with the screw.

Adjust the Water Temperature Limit – Vandal-Resistant Installations

NOTE: If you install the vandal-resistant plug button, save the

handle to adjust the water temperature at a later date.

Using the handle, adjust the water to the desired temperature.

Using the 2.5 mm hex wrench provided, remove and retain the

screw, spring washer, and handle.

Position the vandal-resistant plug button and ﬁrmly press into

place.

Kohler Co. 9 1124215-2-B

7. Installation Checkout

Connect the drain tailpiece to the P-trap.

Using the key provided, remove the aerator from the spout.

If applicable, uncover the drain.

Turn on the main water supply and check for leaks. Adjust as

needed.

Allow the water to run through the spout for about 1 minute to

remove any debris. Check for leaks and adjust as needed.

Temporarily cover the sensors on the faucet or close the water

supplies.

Using the key provided, reinstall the aerator to the spout.

Uncover the sensors on the faucet or turn on the water supplies.

Troubleshooting

Symptoms Probable

Causes Recommended Action

1. No water

ﬂow. A. Filter is

plugged. A. Clean or replace the ﬁlter.

B. Sensor eyes

are dirty. B. Wipe the sensor eyes with a

damp soft cloth. Wipe dry with a

dry soft cloth.

Aerator

Key

1124215-2-B 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-10215 Montageanleitung

Kohler

Kohler K-2338 Series Montageanleitung

Kohler

Kohler Kelston K-T13494 Montageanleitung

Kohler

Kohler Mira Zest Bedienungsanleitung

Kohler

Kohler Veil Bedienungsanleitung

Kohler

Kohler K-T14783 Montageanleitung

Kohler

Kohler K-7827 Montageanleitung

Kohler

Kohler K-514 Bedienungsanleitung

Kohler

Kohler K-433 Montageanleitung

Kohler

Kohler K-T72770 Montageanleitung

Kohler

Kohler Coralais Rite-Temp 114522-2-CE Bedienungsanleitung

Kohler

Kohler 23475-4-BL Bedienungsanleitung

Kohler

Kohler Caxton K-2216 Bedienungsanleitung

Kohler

Kohler Quiet-Close C3-455 Bedienungsanleitung

Kohler

Kohler K-2219 Bedienungsanleitung

Kohler

Kohler ODEON K-8711T Bedienungsanleitung

Kohler

Kohler BRAZN K-702245T Bedienungsanleitung

Kohler

Kohler K-T15806 Bedienungsanleitung

Kohler

Kohler Purist K-T14428 Bedienungsanleitung

Kohler

Kohler K-15635 Bedienungsanleitung

Kohler

Kohler STRAYT 37331T Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

Kohler

Kohler K-3444K-NS Montageanleitung

Kohler

Kohler C3-050 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung