Kohler K-14402 Bedienungsanleitung

Installation Guide

Single-Control Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página“ Español-1”

K-14402 K-14404

1032026-2-C

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Inspect the supply tubing for damage. Replace as necessary.

If possible, install this faucet to the lavatory before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Thread

Sealant Plumbers

Putty

Hex

Wrench

1032026-2-C 2 Kohler Co.

1. Install the Faucet

Apply plumbers putty or other sealant to the underside of the

escutcheon according to the manufacturer’s instructions.

Feed the faucet supply inlets through the faucet hole of the

lavatory, then position the faucet. Slide the bracket and washer

over the studs and tighten the nuts securely to the mounting

studs.

Nut

Bracket

Lavatory

Stud

Supply Inlet

Washer

Escutcheon

Nut

Bracket

Washer

Apply Plumbers

Putty.

Stud

Supply Inlet

Escutcheon

Apply Plumbers

Putty.

Kohler Co. 3 1032026-2-C

2. Connect the Supplies

If the lavatory is not installed, install it at this time. Follow the

lavatory manufacturer’s instructions.

Connect the supply tubes to the supply stops. (Left is hot - right

is cold.)

Wrench-tighten all connections.

Supply

Stop

Supply

Hose

1032026-2-C 4 Kohler Co.

3. Install the Drain - Style A

Disassemble the drain components.

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the lavatory drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the lavatory and tighten.

Ensure the seal hole is facing the back of the lavatory and fully

tighten the nut. Use care to avoid scratching the ﬁnish.

Apply

Plumbers

Putty.

Body

Washer

Body

Seal Hole

Gasket

Nut

Washer

Flange

Kohler Co. 5 1032026-2-C

4. Complete the Drain Installation-Style A

Insert the stopper into the ﬂange.

Remove the body nut from the seal hole.

Insert the short end of the rod into the seal hole and under the

stopper. Loosely secure in place with the body nut.

Remove and adjust the stopper so it lifts approximately 3/8″(1

cm) when opened. To adjust, loosen the stopper nut and shorten

or lengthen the stopper as needed.

Tighten the stopper nut.

Hand tighten the body nut.

Apply three layers of sealant tape plus a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and hand tighten securely.

Slide the rod through one end of the clip and the appropriate

hole in the link. The thumbscrew should face toward the back of

the lavatory.

Run the rod through the other end of the clip.

Clip

Link

Thumbscrew

Rod

Apply Thread

Sealant.

Stopper Nut

Tailpiece

Body Nut

Seal Hole

Rod Body

Stopper

1032026-2-C 6 Kohler Co.

Complete the Drain Installation-Style A (cont.)

If needed, move the link for adjustments. Squeeze the clip and

slide it along the rod.

Push the rod down to the open position.

Kohler Co. 7 1032026-2-C

5. Adjust the Drain Link - Style A

Identify the best hole in the link to allow full operation of the

drain rod and the lift rod.

Align the link hole with the drain rod and slide the clip and the

link onto the drain rod with the thumbscrew facing the back of

the lavatory.

To move the link to the proper position, squeeze the clip and

slide it along the rod.

If not already down, push the drain rod down to the open drain

position.

If required, loosen the thumbscrew on the link.

Align the link with the faucet lift rod and push the lift rod

through the hole in the link.

Ensure that the drain knob is at the bottom of the slot in the back

of the faucet.

With both the drain knob and the drain rod fully down, tighten

the thumbscrew on the lift rod.

Test operation of the drain knob.

Clip

Link

Thumbscrew

Drain Knob

Faucet Body

Lift Rod

Drain Rod

1032026-2-C 8 Kohler Co.

6. Install the Drain - Style B

CAUTION: Risk of product damage. Never pull on the drain

cap to open the drain. Press and release the drain cap once to

close it. Press and release it again to open it.

Remove the seal from the body.

Apply a 1/2″(1.3 cm) diameter ring of plumbers putty or other

sealant around the underside of the body according to the putty

manufacturer’s instructions.

Insert the body into the ﬁxture drain hole.

Attach the rubber washer (tapered side up) to the body.

Install the ﬂat washer over the threads of the body.

Partially thread the nut onto the body. Do not tighten at this time.

Orient the ″KOHLER″logo as desired. Adjustment is not possible

after ﬁnal assembly.

Wrench-tighten the nut.

Apply sealant tape to the top of the tailpiece threads before

screwing it into the body.

Connect the tailpiece to the body.

Remove any excess putty or sealant.

Rubber Washer

Lavatory

Tailpiece

Nut

Body

Flat Washer

Apply plumbers

putty.

Kohler Co. 9 1032026-2-C

7. Installation Checkout

Connect the drain tailpiece into the P-trap.

Ensure all connections are tight.

Remove the aerator and remove any debris.

Turn on the main water supply and check for leaks. Repair as

needed.

Lift and rotate the faucet handle to the full hot position, then the

full cold position. Run water through the spout for about one

minute to remove any debris. Check for leaks and repair as

needed.

Push the lever handle down to close the water supplies, then

reinstall the aerator.

Aerator

1032026-2-C 10 Kohler Co.

Andere Handbücher für K-14402

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler SIMPLICE 596T-4E Bedienungsanleitung

Kohler

Kohler K-4108BR Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler Clearflo K-7160 Bedienungsanleitung

Kohler

Kohler K-T11077 Montageanleitung

Kohler

Kohler 74053T-4E2 Bedienungsanleitung

Kohler

Kohler PATIO ECO K-18645T-Y Bedienungsanleitung

Kohler

Kohler Karbon K-6227A Bedienungsanleitung

Kohler

Kohler 10742A-CP Bedienungsanleitung

Kohler

Kohler Escale K-7219 Bedienungsanleitung

Kohler

Kohler K-75449-BN Bedienungsanleitung

Kohler

Kohler K-7223 Montageanleitung

Kohler

Kohler Loure K-15285 Montageanleitung

Kohler

Kohler K-1110 Kurzanleitung

Kohler

Kohler REGATTA drop in 11303A-GAB-0 Bedienungsanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler AMARETTO K-4864T-1/4 Bedienungsanleitung

Kohler

Kohler K-6356 Bedienungsanleitung

Kohler

Kohler Symbol 18471-4FP Bedienungsanleitung

Kohler

Kohler Devonshire K-TS395-4S Bedienungsanleitung

Kohler

Kohler K-7131 Montageanleitung

Kohler

Kohler Mira Escape Thermostatic 9.0 kW J95Hb/c Bedienungsanleitung

Kohler

Kohler K-1188 Bedienungsanleitung

Kohler

Kohler C3-150 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung