Kohler Clearflo K-7160 Bedienungsanleitung



113176-2-BC 2000 Kohler Co.





 

BEFORE YOU BEGIN

HOW TOUSE THESEINSTRUCTIONS

Please read these instructions carefully to familiarize

yourselfwiththerequiredtools,materials,andinstallation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based onthe latest

product information available at the time of publication.

Kohler Co. reserves the right to make changes in product

characteristics, packaging, or availability at any time

without notice.

NOTES

Observe all local plumbing and building codes.

Inspect waste and supply tubing; replace if

necessary.

If you are installing a new bath, install the drain

before installing the bath. Refer to the

manufacturer’s installation instructions.

Adjustable pop-up drain has removable parts.

Drain “T” is reversible for vertical or horizontal

drainage.

K-7166 and K-7166M is for Seawall 6’ (1.5m)

bath or whirlpool and 14” (35.6cm) Mayflower

bath.

TOOLSREQUIRED

Assorted screwdrivers

Adjustable or open end wrench

Pipe wrenches

Pliers

Plumbers putty

ROUGHING-IN

Fig. #1

2-7/8” (7.3cm)

3” (7.6cm)

1-1/2” N.P.S.

1-1/2” O.D.

7” (17.8cm)

17” (43.2cm) BATH =

14-3/4” (37.5cm)

24” (61cm) BATH =

21-1/2” (54.6cm)

2-7/8” (7.3cm)

3” (7.6cm)

1-1/2” N.P.S.

1-1/2” O.D.

7” (17.8cm)

14” (35.6cm) BATH =

11-1/2” (29.2cm)

16” (40.6cm) BATH =

14” (35.6cm)

K-7160 K-7161

K-7161M

K-7160M

113176-2-BC Kohler Co., Kohler, WI U.S.A.

INSTALLATION

Apply a ring of plumbersputty or other sealantaround the

underside of the strainer according to the putty

manufacturer’s instructions. Position the flat gasket

between the drain ell and the bottom of the bath. Turn the

strainer into the drain ell.

Fig. #2

Drain Ell

Gasket

Strainer

Bath

Apply Plumbers Putty

Tighten the drain ell securely by inserting pliers handles

into the top of the strainer, as shown. Make sure thedrain

elltube isfacingthefront ofthebath. Removeanyexcess

sealant.

Fig. #3

Attachthegaskettotheoverflowell,asshown.Makesure

the tapered end of the gasket is facing up.

Lubricate the O-rings on the overflow ell, and insert the

overflow ell into the tube. Align the overflow ell with the

overflow hole in the bath.

Fig. #4

Overflow Ell

Gasket

Tube

From inside the bath, assemble hold down plate to

overflow ell with screws provided. Tighten all screws.

Fig. #5

Hold Down Plate

3113176-2-BC

Kohler Co., Kohler, WI U.S.A.

FOR BELOW FLOOR INSTALLATIONS: Assemble the

nut and gasket on the drain ell, and the nut and cone

washeronthetube.Alignthepartswiththetee,asshown.

Insert the tubes completely into the tee. Align and tighten

the nuts.

Attach the tailpiece to the tee, and tighten. The tailpiece

may need to be cut for proper fit. The tailpiece should fit

inside the trap 1” (2.5cm) to 2” (5.1cm). Install the bath

according to the manufacturer’s installation instructions.

Make sure the drain tailpiece fits properly into the trap.

Fig. #6

Tube

Nuts

Drain Ell Tee

Gasket

Cone

Washer

FOR ABOVE FLOOR INSTALLATIONS: Assemble the

nut and gasket on the drain ell, and the nut and cone

washeronthetube.Alignthepartswiththetee,asshown.

Insert the tubes completely into the tee. Align and tighten

the nuts.

Attach the tailpiece to the tee, and tighten. The tailpiece

may need to be cut for proper fit. The tailpiece should fit

inside the trap 1” (2.5cm) to 2” (5.1cm). Install the bath

according to the manufacturer’s installation instructions.

Make sure the drain tailpiece fits properly into the trap.

Fig. #7

Tube

Nuts

Drain Ell Tee

Gasket

Cone

Washer

MULTIPLE LIFT ROD MODELS: Choose the lift rod that

extendsmostcloselytothenecessarylength.Positionthe

lift rod assembly directly on the drain stopper. Adjust the

assembly length so the eye of the lift rod is centered over

either top hole of the overflow ell. Refer to the illustration.

Insert the lift rod assembly into the overflow ell. Tighten

the overflow hood to the overflow ell with the two screws

provided.

NOTE: For installations where the overflow hood will be

exposed to high volumes of direct water spray, apply

silicone sealant around the overflow hood. Fig. #8

Top Holes

ATTACHED LIFT ROD ASSEMBLY MODELS: Position

the lift rod assembly directly on the drain stopper. Adjust

the assembly length so the alignment ribs of theoverflow

hood line up with the top edge of the overflow hole in the

bath. Refer to the illustration.

Insert the lift rod assembly into the overflow ell. Tighten

the overflow hood to the overflow ell with the two screws

provided.

NOTE: For installations where the overflow hood will be

exposed to high volumes of direct water spray, apply

silicone sealant around the overflow hood. Fig. #9

Alignment

Ribs

Overflow

Hole

113176-2-BC Kohler Co., Kohler, WI U.S.A.

Assemble the handle to the overflow hood with the screw

provided. It may be necessary to adjust the handle to the

desired position.

Fig. #10

Handle

Overflow

Hood

Insert the drain stopper into the drain ell.

Fig. #11

The drain stopper should rise approximately 3/8” (1cm)

above the strainer.      

         

       

 

Fig. #12

Nut

Stopper

Toggle

If sufficientclearancecannot beobtainedby adjustingthe

stopper, remove the lift rod assembly. Loosen the screw,

and slide the adjusting block up on the adjusting rail to

increase the clearance, or down to decrease the

clearance. Tighten the screw, and insert the lift rod

assembly back into the overflow ell.

Fig. #13

Lift Rod

Assembly

Screw

Adjusting Block

Adjusting Rail

Dieses Handbuch passt für folgende Modelle

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler 23776T-7 Bedienungsanleitung

Kohler

Kohler K-26228T Bedienungsanleitung

Kohler

Kohler K-1035-H2 Montageanleitung

Kohler

Kohler TOUCHLESS 32323T-4 Bedienungsanleitung

Kohler

Kohler K-1630-L Bedienungsanleitung

Kohler

Kohler K-352 Bedienungsanleitung

Kohler

Kohler K-4107T Bedienungsanleitung

Kohler

Kohler Botticelli K-2333 Montageanleitung

Kohler

Kohler Thermostatic Electric Shower Bedienungsanleitung

Kohler

Kohler K-98741 Montageanleitung

Kohler

Kohler K-T16225 Montageanleitung

Kohler

Kohler KUMIN K-18655T-B-CP Bedienungsanleitung

Kohler

Kohler Trend K-11933 Bedienungsanleitung

Kohler

Kohler Kohler K-9245 Montageanleitung

Kohler

Kohler K-T442 Montageanleitung

Kohler

Kohler K-2804 Bedienungsanleitung

Kohler

Kohler K-1954 Montageanleitung

Kohler

Kohler K-9025 Bedienungsanleitung

Kohler

Kohler K-4761 Bedienungsanleitung

Kohler

Kohler K-5805 Montageanleitung

Kohler

Kohler K-19797T Bedienungsanleitung

Kohler

Kohler C3-225 K-4736T-0 Bedienungsanleitung

Kohler

Kohler K-193-4-CP Bedienungsanleitung

Kohler

Kohler 9076 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung