Kohler Mira Agile S Eco Bedienungsanleitung

11285246-W2-D

Mira Agile S Eco, Mira Agile S, Mira Agile ERD+

Mira Agile Sense ERD+, Mira Agile Store EV+, Mira Agile EV+

These instructions must be left with the user

Installation and User Guide

For SPARES,

ADVICE or REPAIRS

please call us free

on 0800 001 4040

(UK only)

1285246-W2-D

Product Model

Number Colour Type 2 Designation

Mira Agile S

Mira Agile S Eco

Mira Agile EV+

B97C Chrome HP-S, HP-SE, LP-S

Mira Agile ERD+

Mira Agile Sense ERD+

Mira Agile Store EV+

B97D Chrome HP-S, HP-SE, LP-S

Introduction

Thank you for choosing a Mira shower. To enjoy the full potential of your new shower,

please take time to read this guide thoroughly, and keep it handy for future reference.

Products manufactured by Kohler Mira Ltd are designed to be safe, provided that they are

installed, used and maintained in good working order, in accordance with our instructions

and recommendations.

Follow all warnings, cautions and instructions contained in this guide, and on, or inside the

shower. This guide is also available in digital format from our website or by contacting our

customer services department.

This product should not be disposed of with your general household waste. When this product

has reached the end of its serviceable life please take it to a recognised facility such as your

local civic amenity site for recycling. Your local authority or retailer will be able to advise you

of your nearest recycling facility.

Type 2 Valves

This product has been certied as a Type 2 valve. It also complies with the Water Supply

(water ttings) regulations 1999. For further information on Type 2 Valves, refer to the TMV2

Requirements Manual (this is available to view or download from our website www.

mirashowers.com).

The approved designation for this product is listed in the table below.

Mira Mixer Showers covered by this guide:

Recommended Usage

Domestic Light Commercial 

Heavy Commercial Healthcare 

Recommended Usage

Guarantee

This product has been designed for domestic use only, Mira Showers guarantee this product

against any defect in materials or workmanship for a period of ve years from the date of

purchase (shower ttings for one year).

Failure to follow the instructions provided with the shower will invalidate the guarantee

For terms and conditions, refer to the back cover of this guide.

31285246-W2-D

Design Registration & Patents

Design Registration:

001312649-0001 to 001312649-0022

Patents:

GB 2 422 886, 2 491 044, 2 500 948, 2 544 770

Euro: 1 672 257, 2 710 194, DE, FR, GB, IT, NL, SE

USA: 8 167 215, 8 517 282

Pack Contents

(2 x Screws, 2 x Wall Plugs, 2 x Flow Reg,

2 x Hex Key, 1 x Grease Sachet)

1 x Shower Unit

Agile S

Agile S Eco

Agile EV+

1 x Wallplate Pack

1 x Component Pack

1 x First Fix Pipe Guide

(2 x Screws, 2 x Wall Plugs, 2 x Hex Key,

1 x Grease Sachet)

1 x Component Pack

Agile S & Agile EV+ Agile S Eco

1285246-W2-D

1 x Installation & User Guide

1 x Guarantee Card

Documents

1 x Shower Unit

1 x Wallplate Pack

(2 x Screws, 2 x Wall Plugs, 2 x Hex Key,

1 x Grease Sachet, 2 x Grubscrew - 1 as

a spare)

1 x Component Pack

1 x First Fix Pipe Guide

Agile ERD+

Agile Sense ERD+

Agile Store EV+

Pack Contents

51285246-W2-D

Important Safety Information

WARNING ! This shower can deliver scalding temperatures. For

continued safe operation, follow all instructions, warnings and

cautions contained in this guide and on or inside the shower.

Periodic maintenance may be required to keep the product in

good working order.

The function of a thermostatic mixing valve is to deliver water

consistently at a safe temperature. In keeping with every other

mechanism, it cannot be considered as functionally infallible and

as such, cannot totally replace a supervisor’s vigilance where that

is necessary. Provided it is installed, commissioned, operated and

maintained within manufacturers recommendations, the risk of

failure, if not eliminated, is reduced to the minimum achievable.

PLEASE OBSERVE THE FOLLOWING TO REDUCE THE RISK

OF INJURY:

INSTALLING THE SHOWER

1. I nstallation of the shower must be carried out in accordance with

these instructions by qualied, competent personnel. Read all

instructions before installing the shower.

2 . DO NOT install the shower where it may be exposed to freezing

conditions. Ensure that any pipework that could become frozen is

properly insulated.

3 . DO NOT perform any unspecied modications to the shower

or its accessories. When servicing only use genuine Kohler Mira

replacement parts.

4 . If the shower is dismantled during installation or servicing then, upon

completion, an inspection must be made to ensure all connections

are tight and that there are no leaks.

USING THE SHOWER

5 . The shower must be operated and maintained in accordance with

the requirements of this guide. Make sure you fully understand how

to operate the shower before use, read all instructions and retain

this guide for future reference.

1285246-W2-D

6. DO NOT switch the shower on if there is a possibility that the water

in the shower unit or ttings is frozen.

7 . The shower can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children must not be

allowed to play with the shower.

8 . Anyone who may have di󰀩culty understanding or operating the

controls of any shower should be attended whilst showering.

Particular consideration should be given to the young, the elderly,

the inrm or anyone inexperienced in the correct operation of the

controls.

9. DO NOT allow children to clean or perform any user maintenance

to the shower unit without supervision.

10. Always check the water temperature is safe before entering the

shower.

1 1 . DO NOT adjust the temperature control rapidly while using the

shower.

12. Use caution when altering the water temperature while in use,

always check the temperature before continuing to shower.

13. DO NOT switch the shower o󰀨 and back on while standing in the

water ow.

14. DO NOT t any form of outlet ow control. Only Mira recommended

outlet ttings should be used.

1 5 . The showerhead must be descaled regularly. Any blockage of the

showerhead or hose may a󰀨ect showering performance.

1 6 . The water supplies to this product must be isolated if the product is

not to be used for a long period of time. If the product or pipework

is at risk of freezing during this period they should also be drained

of water.

1 7 . When this product has reached the end of its serviceable life, it

should be disposed of in a safe manner, in accordance with current

local authority recycling, or waste disposal policy.

71285246-W2-D

Specications

For Type 2 Valves, the supply conditions specied in the TMV2 Requirements Manual take

precedence over the operating parameters which follow.

Pressures

• Max Static Pressure: 10 Bar.

• Max Maintained Pressure: 5 Bar.

• Min Maintained Pressure (Gravity System): 0.1 Bar (0.5 Bar for models with Eco

Showerhead). (0.1 bar = 1 Metre head from cold tank base to showerhead outlet).

Note: For gravity fed or other low pressure systems (0.5 bar or below) do not t the outlet

ow regulator (where applicable).

• For optimum performance supplies should be nominally equal.

Temperatures

• Factory Pre-set (Blend) Shower: 43° C.

• Optimum Thermostatic Control Range: 35° C to 45° C (achieved with supplies of 15° C

cold, 65° C hot and nominally equal pressures).

• Recommended Hot Supply: 60° C to 65° C Note: The mixing valve can operate at higher

temperatures for short periods without damage, however this could detrimentally a󰀨ect

thermostatic performance. For safety and performance reasons it is recommended that

the maximum hot water temperature is limited to 65° C.

• Cold Water Range: up to 25° C.

• Minimum Recommended Di󰀨erential between Hot Supply and Outlet Temperature: 12° C.

Thermostatic Shut-down

• For safety and comfort the thermostat will shut o󰀨 the mixing valve within 2 Seconds if

either supply fails (achieved only if the blend temperature has a minimum di󰀨erential of

12° C from either supply temperature).

Connections

• Inlets: Mixing valve ONLY accepts 15mm OD copper pipe.

IMPORTANT This product is not suitable for use with any other pipe sizes

• Outlet: ½” BSP Flat Face

• Standard connections are:

• Hot - Left, Cold - Right

• Outlet - Bottom

WARNING! This product does not allow for reversed inlets and will deliver dangerously

unstable temperatures if tted incorrectly.

Suitable Plumbing Installations

Gravity Fed:

The thermostatic mixer must be fed from a cold water cistern (usually tted in the

loft space) and a hot water cylinder (usually tted in the airing cupboard) providing

nominally equal pressures.

Mains Pressurised Instantaneous Hot Water System (Combination Boiler):

The thermostatic mixer can be installed with systems of this type with balanced

pressures (Recommended Minimum Maintained Pressure: 1.0 Bar).

1285246-W2-D

Unvented Mains Pressure System:

The thermostatic mixer can be installed with an unvented, stored hot water system.

Pumped System:

The thermostatic mixer can be installed with an inlet pump (twin impeller). The pump

must be installed in a suitable location and in accordance with its instructions.

Installation

General

1. Installation of the shower must be carried out in accordance with these instructions

by qualied, competent personnel.

2. The plumbing installation must comply with all national or local water regulations

and all relevant building regulations, or any particular regulation or practice

specied by the local water supply company.

3. Make sure all pressures and temperatures comply with the requirements of the

shower. See ‘Specications’. For Type 2 Valves, refer to supply conditions given

in the TMV2 Requirements Manual (this is available to view or download from

our website www.mirashowers.com).

4. Full bore/non restrictive servicing valves must be tted in a readily accessible

position adjacent to the shower to facilitate maintenance of the shower.

DO NOT use a valve with a loose washer plate (jumper) as this can lead to a

build up of static pressure.

5. DO NOT apply excessive force to plumbing connections; always provide

mechanical support when making plumbing connections. Any soldered joints

should be made before connecting the shower.

6. Pipework dead-legs should be kept to a minimum.

7. DO NOT install the shower unit in a position where access for maintenance is

restricted.

8. The shower must be tted to a waterproof, at and even wall surface. The two

screws and wall plugs supplied are suitable for most solid wall installations. Alternative

xing screws for panel structures are not supplied. Use both xing points to secure

the shower, be sure to use xings appropriate for the chosen wall structure.

9. When pipework enters the product from the rear through a hole in the wall,

provision must be made to prevent water ingress back into the wall structure.

10.Position the shower unit where the controls are at a convenient height for the

user. Position the showerhead so that the water sprays in line with the bath or

across the opening of a shower cubicle. The installation must not cause the

shower hose to be kinked during normal use.

11. The water supplies to this product should be isolated if the product is not to be

used for a long period of time. If the product or pipework is at risk of freezing

during this period they should also be drained of water.

91285246-W2-D

Note ! There will be occasions when the hose retaining ring will not provide a suitable solution

for Fluid Category 3 installations. In these instances an outlet double checkvalve must be

tted, this will increase the required supply pressure typically by 10 kPa (0.1 bar). Double

checkvalves tted in the inlet supply to the appliance cause a pressure build up, which

a󰀨ects the maximum static inlet pressure for the appliance and must not be tted. For Fluid

Category 5, double checkvalves are not suitable.

12. The position of the shower and shower ttings must provide a minimum air

gap of 25 mm between the showerhead and the spill over level of any bath,

shower tray or basin. There must be a minimum distance of 30 mm between

the showerhead and the spill over lever of any toilet, bidet or other appliance

with a Fluid Category 5 backow risk.

6.0 mm

Tools Required

16 - 19 mm

Zone of

Backflow

Risk

30 mm

Minimum

Toilet or Bidet

FC5

Hand Basin

FC3

Bath or Shower

Tray FC3

Shower

Unit

25 mm

Minimum

25 mm Minimum

1285246-W2-D

Installation

Critical! The installation area must be carefully prepared and all tiles cut or

drilled accurately for a successful installation.

Note: This product DOES NOT allow for reversed inlets and will deliver dangerously

unstable temperatures if tted incorrectly. If the tile cutting area exceeds the

boundaries listed (step 6) below, the wall plate may not conceal drilled holes.

The shower ttings should be positioned at a convenient height for all the family.

Position the ttings to spray across rather then towards the opening of the cubicle

and also away from the shower control. Avoid layouts where the shower hose will

be sharply kinked. This may reduce the life of the hose.

Shower Positioning

To enable sufficient

clearance the valve must

be a minimum 1.1 m

from the ceiling.

Agile ERD+

Offset Valve

to suit

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-24804-4N-CP Bedienungsanleitung

Kohler

Kohler K-14675X Bedienungsanleitung

Kohler

Kohler K-6448 Montageanleitung

Kohler

Kohler STILLNESS Bedienungsanleitung

Kohler

Kohler 17493W-CP Bedienungsanleitung

Kohler

Kohler AVID 97367T-4 Bedienungsanleitung

Kohler

Kohler K-2369 Bedienungsanleitung

Kohler

Kohler 528D Bedienungsanleitung

Kohler

Kohler PURIST 10129T-4 Bedienungsanleitung

Kohler

Kohler Purist K-T97328-4-BN Bedienungsanleitung

Kohler

Kohler K-45415 Montageanleitung

Kohler

Kohler K-6356 Bedienungsanleitung

Kohler

Kohler K-7166-AF Montageanleitung

Kohler

Kohler K-1162-S1HB Kurzanleitung

Kohler

Kohler K-12177 Montageanleitung

Kohler

Kohler R22898-SD-BL Bedienungsanleitung

Kohler

Kohler K-8297TW-HC-0 Montageanleitung

Kohler

Kohler K-T9493 Bedienungsanleitung

Kohler

Kohler K-2419 Montageanleitung

Kohler

Kohler K-596D Bedienungsanleitung

Kohler

Kohler K-856 Kurzanleitung

Kohler

Kohler 45432IN Bedienungsanleitung

Kohler

Kohler K-T5323 Montageanleitung

Kohler

Kohler BEAM K-30939T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung