Kohler K-T9493 Bedienungsanleitung

Installation Guide

Thermostatic Mixing Valve Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T9493 K-T9494

1012606-2-B

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1012606-2-B 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

DANGER: Risk of scalding or other severe injury. Before

completing installation, the installer must set the maximum

water temperature setting of this valve to minimize the risks

associated with scalding hazards according to ASTM F 444.

CAUTION: Risk of scalding. This device has been calibrated at

the factory to ensure a safe maximum water temperature. Any

variance in settings or water inlet conditions from those used

during factory calibration may raise the discharge temperature

above the safe limit, and may present a scalding hazard.

Responsibility for installation and adjustment of this device in

accordance with these instructions lies with the installer.

Shut off the main water supply.

Observe all local plumbing and building codes.

The valve is calibrated to 104° F (40° C) at the ﬁrst stop position,

and the maximum temperature limit stop is positioned so the

outlet water temperature does not exceed 120° F (49° C).

Thermometer Thread

Sealant

Plumbers

Putty Hex

Wrench

Assorted

Screwdrivers

Kohler Co. 3 1012606-2-B

Before You Begin (cont.)

Factory calibrated inlet conditions are: Hot and cold water

pressure = 43-1/2 psi (3 kg/cm) Hot water supply temperature

= 149° F (65° C) Cold water supply temperature = 59° F (15° C).

If inlet conditions differ from those used during factory

calibration, it may be necessary to re-calibrate the valve after

installation. The installer must check the mixed ﬂow

temperature after installation, and adjust the valve as needed

according to the instructions.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the price book.

1012606-2-B 4 Kohler Co.

1. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

NOTE: This valve has been calibrated at the factory to provide 104°

F (40° C) at the mixing valve’s ﬁrst stop position, and 120° F (49° C)

at the maximum temperature limit stop. Check the ″Before You

Begin″section of this manual for detailed factory conditions and

compare them to your inlet water conditions. If they differ

dramatically, then you may need to re-calibrate the valve.

NOTE: Do not turn the mixing valve stem at this time. Turning it

will change the factory calibration setting.

Turn the water on and let the water run for several minutes.

Position a thermometer in the water stream and check the

maximum temperature.

If the existing water supply conditions match the factory

conditions, the water temperature should be close to 104° F (40°

C). If the water temperature differs, then remove and discard the

plaster guard if it is still attached.

Slowly rotate the thermostatic mixing valve stem until the water

temperature is a constant 104° F (40° C). The white mark on the

limit stop should be in line with the black mark on the mixing

valve body. If necessary, carefully pry the limit stop off the valve

cartridge with a thin blade, and re-install it so the white mark

faces upward as required. The limit stop must be correctly

positioned to ensure trim ﬁt.

Limit Stop

Black Mark

on Mixing

Valve Body

Valve

Stem

White Mark

on Limit Stop

Kohler Co. 5 1012606-2-B

Water Temperature Adjustment (cont.)

Do not turn the thermostatic mixing valve stem after you adjust

the temperature setting until you have installed the mixing

handle trim.

1012606-2-B 6 Kohler Co.

2. Install the Trim

Installing Mixing Valve Trim (K-400 and K-401 Models)

Remove and discard the plaster guard if it is still in place.

Thread the collar(s) to the valve and hand tighten.

Verify that each trim seal is correctly installed in an escutcheon

hole. The seal(s) should be installed so the ﬂat side faces outward

and the tapered side faces inward.

Remove the backing from the adhesive gasket material. Starting

at the escutcheon drain opening, carefully apply the gasket

material around the back edge surface of the escutcheon.

Once applied, carefully trim away any excess gasket material so

the escutcheon drain opening is not blocked.

Carefully slip the escutcheon over the collar(s) and against the

ﬁnished wall. Position the escutcheon so the ″Kohler″logo is at

the top.

Secure the escutcheon to the valve with two screws.

Collar

Screw

Collar

Drain

Opening

K-T9494

Escutcheon

Trim

Seal

Adhesive

Gasket

Finished

Wall

Adhesive

Gasket

Volume Control

Valve

K-T9493

Escutcheon

Mixing

Valve

Screw

O-Ring

Cap

Detent

O-Ring

Screw

"Off"

"High"

Round Handle

Volume

Control Knob

Lever Handle

Volume Control

Knob

Rotate

counterclockwise.

Grip

Ring

Kohler Co. 7 1012606-2-B

Install the Trim (cont.)

NOTE: Proceed to the ″Complete Trim Installation″section for the

K-400 mixing valve.

Installing Volume Control Trim (K-401 Model Only)

Rotate the volume control valve stem fully counterclockwise.

Press the volume control knob onto the volume control valve

stem so the indicator graphic for off (smallest line) is to the top

(toward the top escutcheon detent, as shown in the illustration).

Secure the volume control knob to the valve stem with the screw.

For Round Handle: Carefully install the thin O-ring into the ﬁrst

groove in the volume control knob. Fit the grip ring into the

second groove in the volume control knob.

For Lever Handle: Install the O-ring into the groove in the

volume control knob.

For Both Handles: Press the cap into the volume control knob so

the cap detent is in line with the indicator graphic for high on the

volume control knob (as shown in the illustration). If needed,

apply a small amount of lubricant to the inside wall of the cap to

aid in assembly; a capsule of lubricant is included in the

hardware kit.

1012606-2-B 8 Kohler Co.

3. Complete Trim Installation – All Models

NOTE: Units sold internationally will have Celsius temperature

numbers of 32, 40 and 49 on the mixing valve.

Press the mixing valve knob onto the mixing valve stem so the

knob button and ″104″or ″40″mark face upward (toward the

escutcheon detent, as shown in the illustration).

Verify that the knob does not rotate counterclockwise. Do not

press the knob button while trying to rotate the knob.

Turn on the water for a few minutes. Check the water

temperature with a thermometer to conﬁrm that it is at 104° F

(40° C).

If the water temperature matches the marked setting, then rotate

the knob fully counterclockwise so the ″120″or ″49″mark faces

upward.

Let the water run brieﬂy and check the water temperature with

the thermometer to conﬁrm that it is at 120° F (49° C).

If the water temperature matches the marked setting, then rotate

the knob clockwise so the ″104″or ″40″mark faces upward again.

Screw

O-Ring

Grip Ring

Cap

Detent Detent

Detent

Farenheit Celcius

Apply silicone

lubricant if needed.

Mixing Valve

Stem

Mixing Valve

Knob

Kohler Co. 9 1012606-2-B

Complete Trim Installation – All Models (cont.)

Let the water run brieﬂy and check the water temperature with

the thermometer again to conﬁrm that it returns to 104° F (40° C).

Once conﬁrmed, turn off the water.

NOTE: If any of the water temperatures do not match the knob

mark settings, repeat the mixing valve calibration steps in the

″Water Temperature Adjustment″section.

Press the cap onto the valve so the cap detent is in line with knob

button (as shown in the illustration). If needed, apply a small

amount of lubricant to the inside wall of the cap to aid in

assembly; a capsule of lubricant is included in the hardware kit.

1012606-2-B 10 Kohler Co.

Andere Handbücher für K-T9493

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-73078 Montageanleitung

Kohler

Kohler Escale 19046W Bedienungsanleitung

Kohler

Kohler 84625 Handbuch

Kohler

Kohler HYDRO-TOWER 200 Series Bedienungsanleitung

Kohler

Kohler K-6356 Bedienungsanleitung

Kohler

Kohler C3-150 Montageanleitung

Kohler

Kohler Centerset K-15885 Montageanleitung

Kohler

Kohler Family Care 2.0 K-701646T-FM-SHP Bedienungsanleitung

Kohler

Kohler k-10950 Betriebsanleitung

Kohler

Kohler K-101 Bedienungsanleitung

Kohler

Kohler Alteo K-T45117 Montageanleitung

Kohler

Kohler 30440 Bedienungsanleitung

Kohler

Kohler K-1517 Bedienungsanleitung

Kohler

Kohler K-1110-G Kurzanleitung

Kohler

Kohler K-5797 Montageanleitung

Kohler

Kohler K-7223 Montageanleitung

Kohler

Kohler K-7163 Montageanleitung

Kohler

Kohler KT6908 Bedienungsanleitung

Kohler

Kohler K-7779 Montageanleitung

Kohler

Kohler Stance 14787A Bedienungsanleitung

Kohler

Kohler Mira Sport Bedienungsanleitung

Kohler

Kohler Centerset K-15241 Montageanleitung

Kohler

Kohler K-514 Bedienungsanleitung

Kohler

Kohler K-3099 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung