Kohler Oblo K-103B87-SANA-CP Bedienungsanleitung

Installation Guide

Electronic Bathroom Sink Faucet

Français, page “Français-1”

Español, página “Español-1”

1386432-2-A

Tools and Materials

Before You Begin

WARNING: Risk of fresh water contamination. This faucet

contains back-siphonage protection. Do not remove any

internal components.

WARNING: When using electrical products, basic

precautions should always be followed, including the

following:

DANGER: Risk of electric shock. Connect only to a circuit

protected by a Ground-Fault Circuit-Interrupter (GFCI)*.

WARNING: Risk of electric shock. Grounding is required. A

qualiﬁed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before

servicing.

WARNING: Risk of injury or property damage. Please read

all instructions thoroughly before beginning installation.

CAUTION: Risk of product damage. This product contains

sensitive electronic components. Do not store open containers of

chemical or cleaning products near this product. Cleaning rags or

sponges must be rinsed with fresh water before storage.

*Outside North America, this device may be known as a Residual

Current Device (RCD).

1-1/4" to 1-1/2"

Hole Bit1/8"

Sealant TapePlumbers Putty

1386432-2-A 2 Kohler Co.

Before You Begin (cont.)

Provide a constant unswitched 120 VAC electrical outlet located

below the sink within 5’ (1.5 m) of the control box.

Observe all local plumbing and building codes.

Shut off the water supply.

This faucet is for a single-hole bathroom sink.

For new installations, install the faucet and drain to the sink

before installing the sink.

The faucet shown in this guide may differ from your actual

product. The installation steps still apply.

In order for this faucet to function properly, install the faucet so

the sensor points directly toward the user.

Kohler Co. 3 1386432-2-A

1. Faucet Installation

NOTE: Before drilling the mounting hole, use the following

dimensions for proper placement:

A 1-1/4″(32 mm) minimum to 1-1/2″(38 mm) maximum

diameter mounting hole is required.

A minimum distance of 1-3/4″(44 mm) is required between the

back of the spout and the wall to allow access to the screw.

A 1-1/8″(29 mm) maximum distance is required between the

sink bowl edge and the base of the spout.

Install the Faucet

Determine the mounting-hole location.

Drill a hole through the mounting surface according to the

surface manufacturer’s instructions.

Insert the spout with ﬂexible hoses and studs through the

mounting hole.

From under the sink, slide the rubber washer and metal washer

onto the studs.

Thread the nuts onto the studs and wrench-tighten to secure the

faucet to the mounting surface.

Sensor

Rubber Washer

Metal Washer

Nuts

Water Inlet Hose

1386432-2-A 4 Kohler Co.

2. Install the Control Box

NOTE: Verify that the hose will reach the supply stop by attaching

the ﬂex hose to the control box inlet.

NOTE: Determine the proper mounting location according to the

Speciﬁcation Sheet.

Verify that the sensor cable is below the countertop.

Unthread the control box screws to remove the cover.

Drill pilot holes.

Use the standard wall anchors (provided) depending on your

wall material.

Attach the control box to the wall with the arrow pointing

upward. Secure with the two screws (provided).

Inlet

Kohler Co. 5 1386432-2-A

3. Connect the Control Box

IMPORTANT! The control box cover has slots for the spout wires

to ﬁt. Verify that the wires are not pinched when installing the

cover.

Connect the 3-pin sensor cable from the valve cover to the 3-pin

sensor cable from the spout (red, white, and green cables).

Connect the solenoid cable from the valve cover to the solenoid

cable from the valve box (red and green cables).

Connect the 2-pin sensor cable from the valve cover to the 2-pin

sensor cable from the spout (orange and black cables).

Loosely secure the cover to the control box for future access.

Valve

Box

Valve

Cover

Power

Cable

Solenoid

Cable

3-Pin

Sensor

Cable

Power

Cable

Solenoid

Cable

3-Pin

Sensor

Cable

2-Pin

Sensor

Cable

2-Pin

Sensor

Cable

Spout

Wires

1386432-2-A 6 Kohler Co.

4. Supply Connections

Inlet Connections

Connect the ﬂex hose from the control box to the supply stop.

Outlet Connections

Verify that the tube from the spout is the appropriate length to

reach the control box. Cut the tube if necessary. Remove any

burrs and sharp edges.

Insert the tube into the ﬁtting (control box outlet end) until the

tube stops.

Verify that the tube is secure.

Outlet Inlet

Flex Hose

Tube

From Spout

Supply

Stop

Flex Hose

Kohler Co. 7 1386432-2-A

5. Mixing Valve - If Included

If a mixing valve is included with your product, connect the

water outlet hose to the control box outlet.

Attach the supply hose to the control box inlet and outlet of

mixing valve.

Use a 3/8″compression connection (provided) to attach the cold

supply to the mixing valve cold inlet end (marked cold on the

adjustment plate).

Use a 3/8″compression connection (provided) to attach the hot

supply to the mixing valve hot inlet end (marked hot on the

adjustment plate).

Loosen the lock screw and adjust the temperature by rotating the

adjustment plate.

Retighten the lock screw.

Outlet

Hot Cold

Adjustment plate to

set water temperature.

Lock Screw

1386432-2-A 8 Kohler Co.

6. Install the AC Single Supply

IMPORTANT! Verify that you are following the correct power

system installation based on your model number. For a multi-output

AC supply power unit installation, refer to ″Install AC Multi-Output

Supply″. For a hard wire power installation, refer to ″Hard Wire

Installation″.

Unthread the control box screws to remove the control box cover.

Connect the power cords.

Plug the AC supply into the wall outlet.

Secure the excess wire under the counter.

Secure the control box cover to the control box.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

Power

Cord

AC Supply

Kohler Co. 9 1386432-2-A

7. Install AC Multi-Output Supply

Mount the AC supply under the counter using two screws

(provided). Orient as shown.

Remove the cover.

Connect the faucet wire to the faucet.

If needed, cut and strip the AC supply wires to length.

Connect the stripped ends to the bottom terminal block in the

supply box.

Secure the terminal box cover to the terminal box.

NOTE: If a hard wired installation is required, refer to ″Hard Wire

Installation″.

Plug the AC supply into the wall outlet.

Secure any excess wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

Supply

Red

Black

AC Gang

Supply

1386432-2-A 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler ALEO 97826T-4 Bedienungsanleitung

Kohler

Kohler K-8207 Bedienungsanleitung

Kohler

Kohler Discovery Bedienungsanleitung

Kohler

Kohler Trend K-11935 Montageanleitung

Kohler

Kohler SIMPLICE 596T-4 Bedienungsanleitung

Kohler

Kohler TROCADERO K-2247-1 Bedienungsanleitung

Kohler

Kohler K-7223 Bedienungsanleitung

Kohler

Kohler K-5024-T Bedienungsanleitung

Kohler

Kohler TEA-FOR-TWO K-856-H2 Bedienungsanleitung

Kohler

Kohler K-5664 Montageanleitung

Kohler

Kohler 74036T-4E2 Bedienungsanleitung

Kohler

Kohler K-T944 Montageanleitung

Kohler

Kohler 77980T-4 Bedienungsanleitung

Kohler

Kohler COMPONENTS K-EX27462T-NW-CP Bedienungsanleitung

Kohler

Kohler K-7514 Bedienungsanleitung

Kohler

Kohler K-14402 Bedienungsanleitung

Kohler

Kohler K-T11077 Montageanleitung

Kohler

Kohler K-3597 Montageanleitung

Kohler

Kohler K-6812 Bedienungsanleitung

Kohler

Kohler K-15227 Series Montageanleitung

Kohler

Kohler Escale 19046W Bedienungsanleitung

Kohler

Kohler K-11000 Bedienungsanleitung

Kohler

Kohler K-T14783 Montageanleitung

Kohler

Kohler Loure T97330-4-CP Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung