Kramer VS-44DT Bedienungsanleitung

VS-44DT Quick Start (P/N: 2900-300686QS REV 2)

P/N:

2900- 300686QS

Rev:

Scan for full manual

VS-44DT Quick Start Guide

This guide helps you install and use your VS-44DT for the first time.

Go to www.kramerav.com/downloads/VS-44DT to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-44DT 4x4 HDMI/HDBT MatrixSwitcher

1 Set of rack ears

4 IR receiver cables

4 Rubber feet

IRremote control transmitter with batteries

1 Power cord

4 IR emitter cables

1 Quick start guide

Step 2: Get to know your VS-44DT

Feature

Function

IR LED

Lights yellow when receiving an IR signal

IR Sensor

IR receiver for remote control

POWER LED

Lights green when the device is powered on

IN Buttons

Press to select an input after selecting an output (from 1 to 4)

OUT Buttons

Press to select an output followed by an input or OFF (from 1 to 4)

ALL Button

Press, followed by an input to switch this input to all the outputs, or press, followed by the Off button to

disconnect all the outputs

STO Button

Press to store a preset configuration followed by the preset number in which to save it

EDID Button

Press to copythe EDID from an output to an input

LOCK Button

Press and hold to lock the front panel buttons. Press and hold again to unlock

MENU Button

Press to enter the configuration menu or to move up one level when inside the menu

Menu Navigation Pad

Use the Enter, up (▲), down (▼), left (◄), and right (►) buttons to navigate the menu or to modify

parameters or values within the menu

LCD Readout

(20 char x 2 lines)

Displays either the input/output matrix currentlyselected or the menu during configuration

OFF Button

Press after an output button to disconnect the currently selected outputs from the inputs. Press after the

All button to disconnect all currently switched outputs

RCL Button

Press, followed by a preset number to recall the preset configuration

Feature

Function

IR 1

IN 3.5mm Mini Jack

Connect to an IR sensor. Receives IRcommands and sends them over HDBT OUT 1

OUT 3.5mm Mini Jack

Connect to the first IR emitter. Transmits IR commands that are sent over HDBT OUT 1

IR 2

IN 3.5mm Mini Jack

Connect to an IR sensor. Receives IRcommands and sends them over HDBT OUT 2

OUT 3.5mm Mini Jack

Connect to the second IR emitter. Transmits IRcommands that are sent over HDBT OUT 2

IR 3

IN 3.5mm Mini Jack

Connect to an IR sensor. Receives IRcommands and sends them over HDBT OUT 3

OUT 3.5mm Mini Jack

Connect to the third IR emitter. Transmits IR commands that are sent over HDBT OUT 3

IR 4

IN 3.5mm Mini Jack

Connect to an IR sensor. Receives IRcommands and sends them over HDBT OUT 4

OUT 3.5mm Mini Jack

Connect to the fourth IR emitter. Transmits IR commands that are sent over HDBT OUT 4

OUT 1

HDBT RJ-45 Connector

Connect to the first HDBT receiver, (for example, the TP-580RXR)

HDMI Connector

Connect to the first HDMI acceptor, (for example, an HDMI display)

OUT 2

HDBT RJ-45 Connector

Connect to the second HDBT receiver, (for example, the TP-580RXR)

HDMI Connector

Connect to the second HDMI acceptor, (for example, an HDMI display)

HDBT OUT 3 RJ-45 Connector

Connect to the third HDBT receiver, (for example, the TP-580RXR)

HDBT OUT 4 RJ-45 Connector

Connect to the fourth HDBT receiver, (for example, the TP-580RXR)

AUDIO OUT 3.5mm Mini Jack

Connect to an audio acceptor, (for example, active speakers)

RS-232

DATA 3-pin Terminal

Block (G,Rx,Tx)

Connect to a serial source/target

CONTROL 3-pin

Terminal Block

(G,Rx,Tx)

Connect to a serial controller

PROGRAM USB Connector

Connect to a PC to perform firmware upgrades

ETHERNET RJ-45 Connector

Connect to a PC via a LAN

Mains

Power Socket

Connect the mains power cord

Fuse

AC mains supply protection fuse

Power Switch

Turns the device on and off

HDMI IN 1 Connector

Connect to the first HDMI source, (for example, a Blu-ray disk player)

HDMI IN 2 Connector

Connect to the second HDMI source, (for example, a Blu-ray disk player)

HDMI IN 3 Connector

Connect to the third HDMI source, (for example, a Blu-ray disk player)

HDMI IN 4 Connector

Connect to the fourth HDMI source, (for example, a Blu-ray disk player)

IR OUT 3.5mm Mini Jack

Connect to an IR emitter for receiving the combined IR signals from all HDBT port IR

transmissions

IR IN 3.5mm Mini Jack

Connect to an external IR receiver for controlling VS-44DT via an IR remote controller

Step 3: Install the VS-44DT

To rack mount the machine attach both ear brackets to the machine (by removing the three screws

from each side of the machine and replacing those screws through the ear brackets) or place the

machine on a table.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-44DT. For best results, we recommend that you always use

Kramer high-performance cables to connect AV equipment to the VS-44DT.

RJ-45 Pinout:

For the Ethernet and HDBaseT connectors, see the proper wiring

diagram below

For optimum range and performance use the

recommended Kramer cables available at

www.kramerav.com/product/VS-44DT.

PIN EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

Step 5: Connect the power

Connect AC power to the rear of the VS-44DT, switch on its power and then switch on the power on each device.

Step 6: Set operation parameters via the menu buttons

Menu Item

Function

Enterthe menu via the MENU

button on the front panel or the IR

remote control transmitter. Select a

menu item and set parameters as

required.

Audio Settings

Set the audio output to be routed to AUDIO OUT, set the volume level for

each output and toggle mute (on/off) for each output

RS-232 Routing

Turn the RS-232 DATAserial communication routing on and off for each

port. The current state is displayed when entering the RS-232 ROUTING

menu, for example: ON To port-04.

Auto settings

Set auto switching on or off

If you cannot see any video output,

verify that the display, TV, or

projector is in good working order

and is connected to the

VS-44DT. Verify that the

VS-44DT is selected as the source.

Network Status

Set DHCP (on/off) IP address, netmask and gateway settings

Ethernet Status

Displays the following communication parameters: IP address, netmask,

gateway, TCP port number, UDP port number and MAC address

FW Version

Displays the firmware version

Update firmware

Updates the firmware

Step 7: Operate via the front panel buttons, the remote controller and via:

Web pages:

RS-232 and Ethernet:

RS-232

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example (route the video from HDMI In 3 to Out 1):

#VID 3>1<cr>

TCP/IP Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.000.000

Maximum UDP Connections:

Default gateway:

000.000.000.000

Maximum TCP Connections:

TCP Port #:

5000

Full Factory Reset

Menu-> RESETTO DEFAULT-> Change the option to YES and press Enter (to

complete the reset process you need to turn the power off and then on again)

Web Page

Go to the Device settings page and click FACTORY RESET

Protocol 3000

#FACTORY<cr> command

Step 8: Operate the VS-44DT via front panel display using the menu buttons:

To switch an input to an output:

1. Press an OUT button (1to 4).

2. Press an IN button.

To Copy an EDID from an output to an input:

1. Press EDID.

2. Press the required OUT button.

3. Press the required IN button.

4. Press EDID.

To store the current configuration:

1. Press STO.

2. Press the required IN button to which you want to store the configuration.

3. Press STO. The current configuration is stored to the selected preset number.

To recall a preset:

1. Press RCL.

2. Press the required IN button in which the configuration is stored.

3. Press RCL. The current configuration stored in the selected preset number is

recalled.

Technical Specifications:

Inputs:

4 HDMI on HDMI connectors

5 IRon 3.5mm mini jack connectors

Outputs:

2 HDMI on HDMI connectors; 4 HDBaseT on RJ-45 connectors; 5 IR on 3.5mm mini jack connectors

1 Unbalanced stereo audio 1.3Vpp nominal (2Vrms max) / 100Ω on a 3.5mm mini jack connector

Ports:

1 Ethernet on an RJ-45 connector 1 Program on a USBconnector;

1 RS-232 control on a 3-pin terminal block; 1 RS-232 data on a 3-pin terminal block

Maximum Data Rate:

10.2Gbps(3.4Gbps per graphic channel)

Supported Resolutions:

Up to 4K@60Hz (4:2:0)

HDMI Reach:

15m (49ft) @ 8bit resolution; 10m (33ft) @ 12 bit resolution

HDBaseT Reach:

100m (328ft) 4K@30Hz; 180m (590ft) 1080@60Hz@24bpp

Power Consumption:

100-240V AC 50/60Hz 38VA

Operating Temperature:

0° to +40°C (32° to 104°F)

Storage Temperature:

–40° to +70°C (–40° to 158°F)

Humidity:

10% to 90%, RHL non-condensing

Dimensions:

19” x 13.72” x 1U (W, D, H) rack mountable

Shipping Dimensions:

54.3cm x44.2cm x 10.7cm (21.4” x 17.4” x 4.2”) W, D, H

Weight:

3.3kg (7.28lbs) approx.

Shipping Weight:

4.1kg (9.04lbs) approx.

Included Accessories:

Rack ears, 4 IR receiver cables, 4 IR emitter cables; remote control transmitter

Specifications are subject to change without notice at www.kramerav.com

Andere Handbücher für VS-44DT

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer Sierra Video 1208V3S Bedienungsanleitung

Kramer

Kramer VS-88HD Bedienungsanleitung

Kramer

Kramer VS-44UHD Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1616V5S Bedienungsanleitung

Kramer

Kramer VS-42UHD Bedienungsanleitung

Kramer

Kramer 20-04400030 Bedienungsanleitung

Kramer

Kramer VP-8x8 Bedienungsanleitung

Kramer

Kramer VS-1616DN-MD Bedienungsanleitung

Kramer

Kramer 3232HDS Bedienungsanleitung

Kramer

Kramer Sierra Video 1616V3 Bedienungsanleitung

Kramer

Kramer VS-88HDxl Bedienungsanleitung

Kramer

Kramer VP-8x8AK Bedienungsanleitung

Kramer

Kramer VP-4x4 Bedienungsanleitung

Kramer

Kramer VP-16x18AK Bedienungsanleitung

Kramer

Kramer VS-8FDxl Bedienungsanleitung

Kramer

Kramer VS-88HDCPxl Bedienungsanleitung

Kramer

Kramer Sierra Video 3264V5xl Bedienungsanleitung

Kramer

Kramer 21-70686010 Bedienungsanleitung

Kramer

Kramer VS-84HDCPxl Bedienungsanleitung

Kramer

Kramer VP-4x4 Bedienungsanleitung

Kramer

Kramer VS-4x4YCx1 Bedienungsanleitung

Kramer

Kramer VS-88HCB Bedienungsanleitung

Kramer

Kramer VP-26 Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1616V3S Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung