Kusam-meco KM 071 Bedienungsanleitung

An ISO 9001:2008 Company

G-17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015. INDIA.

Sales Direct.: 022 -2 4156638, Tel. : 022-241224540, 24181649, Fax : 022 - 24149659

Email : [email protected], Website : www.kusamelectrical.com

An ISO 9001:2008 Company

All Specifications are subject to change without prior notice

Navin.com/D.drive/sandeep gupta/New catlog Dec 2011/K 071.cdr

The KM 071 Milliamp Process Clamp Meter is a Hand-held battery

operated clamp meter that measures 4-20 mA DC without breaking

the electrical circuit. Unlike conventional clamp meters, this meter

features a small jaw that easy to reach any place there is a cable

carrying with a current.. This meter takes a magnetic modulated

technology, it can reach excellent sensitivity with great anti Earth

Magnetical Field ability.

GENERAL SPECIFICATIONS :

íJaw Opening size : 5 mm max.

íDC mA measurement (4-20mA); 0-40mA

íElectronic Zero

íPercentage span (0-100%)

íBacklight display

íMeasurement spotlight LED

íData Hold

íOperating Temperature : -10°C to 50°C

íStorage Temperature : -25°C to 70°C

íOperating Humidity : < 90% @ < 30°C, < 75% @ 30 to 50°C

íPower Supply : 9V battery, IEC LR6

íDimension : 59 (H) X 38 (W) X 212 (L) mm

íWeight : Approx. 260 gm ( battery included )

ELECTRICAL SPECIFICATIONS - KM 071

PERCENTAGE SPAN

20mA DC

16 mA DC

12mA DC

8mA DC

100%

75%

50%

25%

4mA DC

3.6mA DC

3.2mA DC

2mA DC

-2.5%

-5.0%

-12.5%

Range

CURRENT RANGE DC

Resolution Accuracy

± 40.00mA DC 0.01mA ±(0.5% rdg + 5 dgts)

Maximum Reading : ± 40.00mA

Error by Earth Magnetic Field : < ± 0.20mA

4-20mA DC PROCESS CLAMP METER

Model KM 071

6 FUNCTIONS 2 RANGES

LIST OF PRODUCTS

OPERATION

MANUAL

* Digital Multimeter

* Digital AC & AC/DC Clampmeter

* AC Clamp Adaptor

* AC/DC Current Adaptor

* Thermo Anemometer

* Thermo Hygrometer

* Distance Meter

* Digital Lux Meter

* Network Cable Tester

* Power Factor Regulator

* Earth Resistance Tester

* Digital Panel Meters

* DC Power Supplies

* High Voltage Detector

* Calibrators

* Gas Analysers

* Frequency Counter

* Function Generator

* Phasing Sticks

* Battery Tester

* Waterproof Pen Testers

* Solar Power Meter

* EMF Detector

* Wood, Paper & Grain Moisture Meter

* Transistorised Electronic Analog & Digital

Insulation Resistance Testers(upto 10 KV)

* Digital Sound Level Meter & Sound Level

Calibrator

* Digital contact & Non-contact Type Tachometer

* Digital Non-contact (infrared) Thermometer

* Maximum Demand Controller/Digital Power

Meter

* Digital Hand Held Temperature Indicators

MILLIAMP PROCESS

CLAMPMETER

MODEL - KM 071

KUSAM-MECO July 2011

MILLIAMP PROCESS

CLAMPMETER

MODEL - KM 071

KUSAM-MECO July 2011

TABLE OF CONTENTS

TITLE PAGE

Introduction........................................................1

Features..............................................................2

Product Description ..........................................3

Electrical Specification......................................4

Operation............................................................4

Measurement .....................................................6

Battery replacement..........................................7

Test Certificate ..................................................8

Warranty ............................................................9

KUSAM-MECO July 2011

1. INTRODUCTION

The KM 071 Milliamp Process Clampmeter is a

hand-held battery operated Clampmeter that

measures 4-20mA DC without breaking the

electrical circuit. Unlike conventional clampmeters

this meter features a small jaw that easy to reach

any place there is a cable carrying with a current.

This meter takes a magnetic modulated

technology, and it can rach excellent sensitivity

with great anti Earth Magnetic Field ability.

1KUSAM-MECO July 2011

2. FEATURES

?DC mA measurement (4-20mA); 0-40mA

?Electronic zero

?Jaw Size : 5mm

?Percentage span (0-100%)

?Data Hold

?Display backlight

?Measurement spotlight LED

?Operating Temperature : -10°C to 50°C

?Storage Temperature : -25°C to 70°C

?Operating Humidity : <90% @ <30°C

<75% @ 30°C to 50°C

?Power Supply : 9V Alkaline, IEC LR6

?Dimension : 59(H) X 38(W) x 212(L)mm

?Weight : 260g (including battery)

KUSAM-MECO July 2011

3. PRODUCT DESCRIPTION

1. Transformer jaw :

through the conductor.

Pick up the DC flowing

2. Spotlight button : Turn the Spotlight on or off.

3. Zero button :

the display.

Removes offset and zeros

4. Backlight button :

of LCD.

Turn on or off the backlight

5. Power Switch : Turn on or off the meter.

6. HOLD button :

reading.

Captures and holds the current

7. LCD : Display the current value and percentage.

KUSAM-MECO July 2011

4. ELECTRICAL SPECIFICATIONS :

?Current Ranges : ± 40.00mA

?Resolution : 0.01mA

?Accuracy : ±0.5% of reading ± 5 digits

?Maximum Reading : ±40.00mA

?Error by Earth Magnetic Field : < ± 0.20mA

5. OPERATION & MEASUREMENT :

The following sections give more detail about

the Meter’s features.

5.1 Operation

The percentage Span feature displays the

span for 4 to 20mA loops.

20 mA

16 mA

12 mA

8 mA

100%

75 %

50 %

25 %

0 %

-2.5 %

-5.0 %

-12.5%

4 mA

3.6 mA

3.2 mA

2 mA

5.2 Zero Adjustment

Before taking each measurement, press the

ZERO button to zero the display by removing

DC offset. Make sure the clamp jaws are

closed and no current is flowing through them.

5.3 Backlight

Press the backlight button to turn the backlight

on or off.

KUSAM-MECO July 2011

5.4 Measurement Spotlight LED

The measurement Spotlight LED helps to

quickly find mA signal wires. Press the

Spotlight button to turn the Spotlight on or off.

5.5 Display HOLD

To avoid electric shock, when Display HOLD is

activated, the display will not change when a

different current is applied.

Press the HOLD button to activate Display

Hold mode.

The symbol “DH” are displayed and the Meter

freezes the display. To exit & return to normal

operation, press the HOLD button a second

time.

Warning

The Clampmeter is not for use on non-insulated

conductors.

Measurements can be taken with the clamp

approach into any position.

For accurate measurements :

?Always zero the Meter prior to taking

measurements.

?Zero the Meter as close to the measurement

source position as possible.

?Make sure the clamp is free of contamination.

KUSAM-MECO July 2011

6. MEASUREMENT

?With the clamp disconnected from any

conductor, press the power switch to turn the

meter ON. Then, you might wait for about 5

seconds.

?Clamp the jaw around the conductor under

test. The meter displays the measured

conductor current.

?A positive reading indicates current flowing in

the direction of the arrow on the clamp.

?A negative reading indicates current flowing in

the opposite direction of the arrow.

?Do not clamp more than one wire. Currents

cancel and no results are returned.

The small secondary display shows the reading

in terms of percentage span.

Note :

To reduce magnetic influences, zero the Meter in

the same position or jaw direction that is used for

the measurement.

KUSAM-MECO July 2011

7. BATTERY REPLACEMENT

To avoid false readings, that could lead to

possible electric shock or personal injury,

replace the battery as soon as the low

battery indicator “ ” appears.

1. Turn the Meter off

2. Use a flat head screwdriver to loosen the

battery compartment door screw, and remove

the door from the case bottom.

3. Remove the battery.

4. Replace the battery with a new 9V battery.

5. Reattach the battery compartment door to the

case bottom and tighten the screw.

WARNING

To replace the battery :

KUSAM-MECO July 2011

MUMBAI

TEST CERTIFICATE

MILLIAMP PROCESS

CLAMPMETER

This Test Certificate warrantees that

the product has been inspected and

tested in accordance with the published

specifications.

The instrument has been calibrated by

using equipment which has already

been calibrated to standards traceable

to national standards.

MODEL NO. ___________

KM 071

SERIAL NO. ___________

DATE: ___________

ISO 9001

REGISTERED

PASS

KUSAM-MECO

KUSAM-MECO July 2011

WARRANTY

Each “KUSAM-MECO” product is warranted to be

free from defects in material and workmanship

under normal use & service. The warranty period

is one year (12 months) and begins from the date

of despatch of goods. In case any defect occurs in

functioning of the instrument, under proper use,

within the warranty period, the same will be

rectified by us free of charges, provided the to and

fro freight charges are borne by you.

This warranty extends only to the original buyer or

end-user customer of a “KUSAM-MECO”

authorized dealer.

This warranty does not apply for damaged Ic’s,

fuses, burnt PCB’s, disposable batteries, carrying

case, test leads, or to any product which in

“KUSAM-MECO’s” opinion, has been misused,

altered, neglected, contaminated or damaged by

accident or abnormal conditions of operation

or handling.

“KUSAM-MECO” authorized dealer shall extend

this warranty on new and unused products to end-

user customers only but have no authority to

extend a greater or different warranty on behalf of

“KUSAM-MECO”.

G 17,Bharat Industrial Estate, T. J. Road,

Sewree (W), Mumbai - 400 015. INDIA.

Sales Direct : (022) 24156638

Tel. : (022) 24124540, 24181649.

Fax : (022) 24149659

Email : [email protected]

Website : www.kusamelectrical.com

www.kusam-meco.co.in

KUSAM-MECO July 2011

“KUSAM-MECO’s” warranty obligation is limited,

at option, free of charge repair, or replacement of

a defective product which is returned to a

“KUSAM-MECO” authorized service center within

the warranty period.

THIS WARRANTY IS BUYER’S SOLE AND

EXCLUSIVE REMEDY AND IS IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.

“KUSAM-MECO” SHALL NOT BE LIABLE FOR

ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES,

INCLUDING LOSS OF DATA, ARISING FROM

ANY CAUSE WHATSOEVER.

All transaction are subject to Mumbai Jurisdiction.

Inhaltsverzeichnis

Andere Kusam-meco Messgerät Handbücher

Kusam-meco

Kusam-meco KM 4235ER Bedienungsanleitung

Kusam-meco

Kusam-meco KM 117A Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2782 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 888PMR Bedienungsanleitung

Kusam-meco

Kusam-meco KM 175D Bedienungsanleitung

Kusam-meco

Kusam-meco KM-CAL-802 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 181 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 63A Bedienungsanleitung

Kusam-meco

Kusam-meco KM-CAL-906 Bedienungsanleitung

Kusam-meco

Kusam-meco 108 Bedienungsanleitung

Kusam-meco

Kusam-meco 9999 Bedienungsanleitung

Kusam-meco

Kusam-meco KM-CAL-804 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 8041 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 981 MK-1 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 078 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 088 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2240 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 076 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2784-T Bedienungsanleitung

Kusam-meco

Kusam-meco KM 503 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 711 Bedienungsanleitung

Kusam-meco

Kusam-meco 2781 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2009 Bedienungsanleitung

Kusam-meco

Kusam-meco KM-CAL-700 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung