La Crosse Technology Tomorrow's Weather Today TX25U Bedienungsanleitung

TX25U

915 MHz

WIRELESS WEATHER STATION

INSTRUCTION MANUAL

ADDITIONAL EQUIPMENT (not included)

1. Two fresh AAA 1.5V alkaline batteries for the remote temperature sensor.

3. One, Philips screwdriver for mounting.

QUICK SETUP

Hint: Use good quality Alkaline Batteries; avoid rechargeable batteries.

1. Have the Wireless Weather Station and Temperature sensor 3 to 5 feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the Temperature sensor first and next into the Wireless Weather

Station.

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the Wireless Weather Station and the temperature sensor will begin to communicate with

each other, and the display will show both the indoor temperature and an outdoor temperature. If the

Wireless Weather Station does not display both temperatures after the 15 minutes, please retry the

set up as stated above. After both indoor and outdoor temperatures are displayed for 15 minutes you

can place your temperature sensor outdoors, and set your time.

The temperature sensor should be placed in a dry, shaded area (ex: under the eve of a roof). The

temperature sensor has a range of 330 feet. Any walls that the signal will have to pass through will

reduce distance. An outdoor wall or window will have up to 20 feet of resistance and an interior wall

will have up to 10 feet of resistance. Your distance plus resistance should not exceed 330 feet in a

straight line.

NOTE: Fog and mist will not harm your temperature sensor, but direct rain must be avoided.

FIGURE 1

Optional Probe

w/ 6 Foot Wire

DETAILED SETUP GUIDE

I. BATTERY INSTALLATION (When one Temperature sensor is being used)

1. First, insert the batteries to the Temperature sensor (see “A. Temperature sensor” below).

2. Within 2 minutes of powering up the sensor, insert the batteries to the Weather Station (see

“B. Wireless Weather station” below). Once the batteries are in place, all segments of the

LCD will light up briefly. Following the indoor temperature and the time as 12:00 will be

displayed, and the signal reception icon will flash. If they are not shown in LCD after 60

seconds, remove the batteries and wait for at least 60 seconds before reinserting them. Once

the indoor data is displayed user may proceed to the next step.

3. After the batteries are inserted, the Weather Station will start receiving data signal from the

sensor. The outdoor temperature should then be displayed on the Weather Station. If this does

not happen after 2 minutes, the batteries will need to be removed from both units and reset

from step 1.

A. TEMPERATURE SENSOR

1. Remove the Battery Cover.

2. Observing the correct polarity, install 2 “AAA” Alkaline

Batteries—make sure they do not spring free, or start-up

problems may occur.

3.Replace the Battery Cover.

OUTDOOR TEMPERATURE

The temperature received from the remote temperature sensor is viewed in the OUTDOOR LCD.

When there is more than one remote temperature sensor unit in operation, a “boxed” number will

appear to the right of the temperature. This indicates which remote temperature sensor unit (1, 2, or

3) is currently displaying its data in the OUTDOOR LCD. (This feature is explained in further detail in

the section—Adding Remote Temperature Sensors).

OPTIONAL CHANNEL 2 TEMPERATURE PROBE

When the temperature probe is connected to the remote temperature sensor, the WS-9029U’s

channel 1 will display the remote temperature sensor data, and channel 2 will display the temperature

probe data. The remote temperature sensor data will always be displayed on the channel 1 and the

temperature probe on the channel 2.

If the probe on remote temperature sensor is unplugged, the "probe channel" on WS-9029U LCD will

show "---", the remote temperature sensor displayed value will still be shown.

The probe can be connected to the remote temperature sensor anytime. There is no need to reset the

units. The Weather Station will automatically detect the temperature probe and will display the

temperature probe data in channel 2.

ADDING TEMPERATURE SENSORS (OPTIONAL)

The WS-9029U is able to receive signals from 2 remote temperature sensors (TX-25U). These extra

sensors can be purchased through the same dealer as this unit

Battery

Compartment

Battery

Cover

Remote

Temperature

Sensor (TX-25U)

A. SET-UP OF MULTIPLE SENSORS

1. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds. During these

60 seconds, press any button 20 times to discharge any excess power.

2. Insert the batteries to the first sensor.

3. Within 2 minutes of powering up the first sensor (Temperature sensor with probe), insert the

batteries to the Weather Station. Once the batteries are in place, all segments of the LCD will

light up briefly. Following the indoor temperature/humidity and the time as 12:00 will be

displayed, and the signal reception icon will flash. If they are not shown in LCD after 60

seconds, remove the batteries and wait for at least 60 seconds before reinserting them.

4. The outdoor temperature from the first sensor (channel 1) should then be displayed on the

Weather station. If this does not happen after 2 minutes, the batteries will need to be removed

from both units and reset from step 1.

5. If the temperature probe has been used, the outdoor temperature from channel 2 will then be

displayed. Otherwise, the outdoor temperature will display “---“.

Note: The temperature probe from the first sensor will always occupy “channel 2”. Channel 2 can

only be used for the temperature probe. If you choose not to use the temperature probe, Channel

2 will display “---“.

6. Insert the batteries to the second sensor as soon as the outdoor temperature readings from

the first sensor are displayed on the Weather station.

NOTE: You must insert the batteries into the second sensor within 30 seconds of

reception of the first sensor.

7. The outdoor temperature from the second sensor and the "channel 3" icon should then be

displayed on the Weather station. If this does not happen after 2 minute, the batteries will need

to be removed from all the units and reset from step 1.

Note: only the readings from the internal sensor of the second sensor will be displayed in “channel 3”

IMPORTANT: Transmission problems will arise if the setting for additional sensors is not

followed as described above. Should transmission problems occur, it is necessary to

remove the batteries from all units and start again the set-up from step 1.

B. VIEWING AND OPERATING WITH MULTIPLE TEMPERATURE SENSOR UNITS

1. To view the temperature of a different remote temperature sensor unit, press and release the

SET/CH button. A shift from one “boxed” number to the next should be observed in the

OUTDOOR LCD.

2. To determine which remote temperature sensor reading is displayed on the 3 channels, match the

temperature displayed on each channel, with the corresponding temperature displayed on the

LCD of each remote temperature sensor.

3. To view the Minimum/Maximum temperature: first select which remote temperature sensor to read

data from (indicated by the “boxed” number), then press the SET/CH button. Pressing this button

once will display the minimum temperature, and the date and time the data was recorded.

Pressing this button a second time (while “MIN” is still displayed, otherwise press the button twice)

will display the same data for the maximum recordings.

4. To reset the Minimum/Maximum readings, press and hold the MIN/MAX/+ button for 5 seconds,

this will reset all the minimum and maximum data from all sensors.

MOUNTING

THE REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket/stand from the temperature sensor.

2. Place the mounting bracket over the desired location.

3. The mounting bracket can attach to the sensor in the middle of the back or on the bottom.

4. Through the 3 screw holes of the bracket, mark the mounting surface with a pencil.

5. Screw mounting bracket onto the mounting surface. Ensure that the screws are flush with the

bracket.

6. Insert the remote temperature sensor into the bracket.

Problem: No outdoor temperature is displayed.

Solution: 1) Remove all batteries, reinsert into sensor first, then into the wireless weather station.

2) Place remote temperature sensor closer to wireless weather station.

3) Be sure all batteries are fresh.

4) Place remoter temperature sensor and wireless weather station in position so the straight-line

signal is not passing through more than 2 or 3 walls.

Problem: Temperatures do not match if units are placed next to each other.

Solution: Each remote temperature sensor is manufactured to be accurate to within 1 degree plus or

minus and under normal conditions, so two sensors could be as much as 2 degrees different.

However, the difference can be exaggerated further because the sensors are designed for

different working environments. The indoor sensor is less responsive to ambient air currents

because of the shielding effect of the display's case. In addition, the case can act as a heat

sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat).

Also, the much greater range of the remote temperature sensor requires a different calibration

curve than the indoor range. Error is usually greater at the extreme ends of a range, making it

harder to compare different ranges with different curves. Under non-laboratory conditions, it is

difficult to compensate for the above factors and obtain an accurate comparison.

MAINTENANCE AND CARE INSTRUCTIONS

9 Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units.

9 Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they

may mark the displays and casings.

9 Do not submerge in water.

9 Immediately remove all low powered batteries to avoid leakage and damage.

9 Opening the casings invalidates t he warranty. Do not try to repair the unit. Contact La Crosse

Technology for repairs.

WARRANTY INFORMATION

La Crosse T echnology, Ltd provides a 1-year limited warranty on this product against manufac turing defects in materials and

workmanship.

Bottom of sensor

inserted into Mounting

Bracket

Back middle o

sensor inserted into

Mounting Bracket

This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to

the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse T echnology, Ltd for problem

determination and service procedures. W arranty service can only be performed by a La Crosse T echnology, Ltd authorized service

center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse

Technology, Ltd’s authorized service center.

La Crosse T echnology, Ltd w ill repair or replace this produc t, at our option and at no charge as stipulated herein, w ith new or

reconditioned parts or products if found to be defective during the limited w arranty period specified above. All replaced part s and

products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts

and products assume the remaining original w arranty, or ninety (90) days, whichever is longer. La Crosse T echnology, Ltd will pay all

expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a

product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping

charges incurred in getting y our La Crosse T echnology, Ltd product to a La Crosse T echnology, Ltd authorized service center. L a

Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only.

Your La Crosse T echnology, Ltd w arranty covers all defects in ma terial and w orkmanship with the following specified exceptions: (1)

damage caused by accident, unreasonable use or neglect (including t he lack of reasonable and necessary maintenance); (2) damage

occurring during shipment (claims must be pr esented to the carrier); (3) damage to, or deterioration of, any accessory or decor ative

surface; (4) damage resulting from failure to follow instructions contained in y our owner’s manual; (5) dam age resulting from t he

performance of repairs or alterations by someone other than an authoriz ed La Crosse T echnology, Ltd authorized service center; (6)

units used for other than home use (7) app lications and uses that this product was not intended or (8) the products inability to receive a

signal due to any source of interference.. T his warranty covers only actual defects within the product itself, and does not co ver the cost

of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misr epresentation by the se ller or

performance variations resulting from installation-related circumstances.

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILIT Y FOR INCIDENTAL, CONSEQUENTIAL, PUNIT IVE, OR OT HER

SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO

BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. T HIS PRODUCT IS NOT A T OY. KEEP OUT OF

CHILDREN’S REACH.

This w arranty gives y ou specific legal rights. You may also have other rights specific to y our State. Some States do no allow the

exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology

2809 Losey Blvd. S.

La Crosse, WI 54601

Phone: 608.782.1610

Fax: 608.796.1020

e-mail:

[email protected]

(warranty work)

[email protected]

(information on other products)

web:

www.lacrossetechnology.com

mechanical or chemical procedures without written permission of the publisher.

This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made in the

next issue. We accept no liability for technical mistakes or printing errors, or their consequences.

All trademarks and patents are acknowledged.

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology 724-1710v2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-9611U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7091UD Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA79103v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-145 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1510-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7038U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9035TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS7059 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9016TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1610TWC-IT Technisches Datenblatt

La Crosse Technology

La Crosse Technology 308-1451H Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7075UF Bedienungsanleitung

La Crosse Technology

La Crosse Technology S75617 Abmessungen

La Crosse Technology

La Crosse Technology WS-7025U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1517 Abmessungen

La Crosse Technology

La Crosse Technology WS1506 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7095U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7026U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86234 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9031U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2811U-IT Technisches Datenblatt

La Crosse Technology

La Crosse Technology T83646v2 Abmessungen

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung