La Crosse Technology WS-7026U Bedienungsanleitung

WS-7026U

Wireless 433 MHz

Radio-Controlled Weather Station

Instruction Manual



Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 4-5

Quick Set-Up Guide 5

Detailed Set-Up Guide

Battery Installation 5-6

Program Mode

Function Keys 7

12/24 Hour Time Setting 7

Time Zone Setting 7-8

Daylight Saving Time Setting 8

Time Setting (WWVB & Manual) 9-10

Setting Day, Date and Year 10

Selecting °F or °C 11

Setting the LCD Contrast 11

Features

Back Light 12

Weather Forecast Icons 12-13

Indoor Temperature, Humidity & Comfort

Level Indicator

Outdoor Temperature & Humidity 14

Minimum & Maximum Records (Indoor,

Outdoor & Resetting)

14-15

Alarm (Setting, Snoozing & Stopping) 15-16

Additional Remote Control Sending Units

(Set-Up, Viewing & Operation)

16-18

Mounting 18-20

Troubleshooting 21

Maintenance & Care 22

Specifications 23

Warranty Information 24

TABLE OF CONTENTS

INVENTORY OF CONTENTS

1. The Weather Station (Figure 1).

2. One TX4U Thermo Hygro Transmitter with mounting bracket (Figure

2).

3. Three each ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction Manual and Warranty Card.



Figure 1

Time LCD

Date LCD

Forecast LCD

Indoor LCD

Outdoor LCD

ADDITIONAL EQUIPMENT (not included)

1. Four fresh AA 1.5V batteries.

2. One Philips screwdriver.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado and transmits the

exact time signal continuously throughout the United States at 60 kHz. The signal

can be received up to 2, 000 miles away through the internal antenna in the weather

station. However, due to the nature of the Earth’s Ionosphere, reception is very

limited during daylight hours. The weather station will search for a signal every

night when reception is best. The WWVB radio station derives its signal from the

NIST Atomic clock in Boulder, Colorado. A team of atomic physicists are

continually measuring every second, of every day, to an accuracy of ten billionths of

Figure 2

a second per day. These physicists have created an international standard measuring

a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

QUICK SET-UP GUIDE

1. Insert two AA batteries into the Thermo Hygro Transmitter.

2. Insert two AA batteries into the WEATHER STATION.

3. Wait 5 minutes or until the outdoor temperature and humidity are

displayed in the OUTDOOR LCD (Liquid Crystal Display).

4. Wait 6-10 minutes (in ideal reception conditions) for the WWVB time

to be displayed in the TIME LCD. If the WWVB takes longer to set,

you may manually set the time (see complete instructions). Or you can

wait until after the weather station conducts its programmed search at

the ideal reception time period of 12:00 AM to 6:00 AM.

5. Mount the units ensuring that all units are sending and receiving

signals.

Note: The Thermo Hygro Transmitter transmits a signal every 3 minutes.

After the batteries have been installed, the weather station will search for

the signal for a duration of 5 minutes. If there is no temperature reading in

the OUTDOOR LCD after 5 minutes, make sure the units are within range

of each other or repeat the battery installation procedure.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. THERMO HYGRO TRANSMITTER

1. Pull the cylindrical rain cover off the transmitter.

2. Remove the battery cover (located on the backside

of the transmitter above the mounting post and

bracket).

3. Press the arrow and slide the battery cover off.

4. Observing the correct polarity install 2 AA

batteries.

5. Replace battery cover and place rain cover snugly

onto the transmitter.

B. WEATHER STATION

1. Remove the battery cover. To do this, insert

a solid object in the space provided at the

lower-central position of the battery cover,

then push up and pull out on the battery

cover.

2. Observe the correct polarity and install 2 AA

batteries.

Battery

Cover

3. Replace the battery cover.

Note: Immediately after the batteries have been installed, each LCD

(Liquid Crystal Display) will flash and a tone will sound. Within a few

seconds the indoor temperature, indoor relative humidity and the

weather icons (sun and clouds) will be displayed. If not, then remove

batteries for 10 seconds and reinstall. If the outdoor temperature is not

displayed within four minutes, remove batteries from both units, wait 10

seconds and reinstall. The time will show -:-- and start searching for

the signal. If it successfully receives the time signal (usually at night), it

will display the correct time (default is Eastern).

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass or either the IN or the

OUT button is pressed during programming modes, the unit will set the last

information entered—the display will stop flashing and return to normal

time-date readings. If you don’t leave the program mode during the

programming of sections III through VIII, you can advance to step 3 of the

next program setting. If you do leave the program setting (or want to

program a specific setting) follow each instructional step to program that

setting.

I. FUNCTION KEYS

The function keys are operated by pressing the top or bottom of the key

corresponding to the operation that you want to perform.

II. 12 OR 24 HOUR TIME SETTING

1. Press and hold the SET button for 3 seconds or until “12 h”

flashes in the DATE LCD.

2. Press the CH button to toggle between 12 and 24-hour time.

3. Press the SET button to confirm the 12/24-hour setting and to

advance to Time Zone Setting.

III. TIME ZONE SETTING

The default time zone is EST “-5hr” (Eastern Standard Time). To

change this setting:

1. Press and hold the SET button for 3 seconds or until “12 h”

OR “24 h” flashes in the DATE LCD.

2. Press the SET button 1 more time to enter the Time Zone

setting mode. The default Time Zone “-5” will flash in the

DATE LCD.

3. Select your appropriate time zone using the CH button.

During selection of the Time Zone, the 3 letter abbreviations

for the time zones found in North America will flash across

the TIME LCD. Observe the chart below showing the

corresponding abbreviations, time zones and codes.

TIME ZONES

GMT 0

Atlantic -4

EST; Eastern -5

CST; Central -6

MST; Mountain -7

PST; Pacific -8

ALA; Alaska -9

HAW; Hawaii -10

Note: There are more time zones represented by numbers than there are

represented by 3 letter abbreviations. If you live in North America you

need only be concerned with the ones in the chart above.

4. Press the SET button to confirm and advance to the Daylight

Saving Time setting.

IV. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the SET button for 3 seconds or until “12 h” or

“24 h” flashes in the DATE LCD.

2. Press the SET button 2 more times to reach the DST selection

mode. “DST 1” is the default setting and will be flashing in

the DATE LCD.

3. Press the CH button to select “DST 0” or “DST 1.”

4. “DST 0” indicates that the feature is off and the WWVB will

not change times automatically. “DST 1” indicates that the

feature is on and the WWVB will change times automatically.

Note: Some locations (Arizona and parts of Indiana) do not

follow Daylight Saving Time, and should select “DST 0.”

5. Press the SET button to confirm and advance to the Time

setting mode.

V. TIME

There are two methods by which the time can be set:

A) Automatically via WWVB reception or

B) Manually

A. WWVB (Remote Control Time)

This method requires you to do nothing except wait for the signal

to be received and to select a time zone. Reception usually takes

approximately 6-10 minutes during optimal conditions. The best

conditions for reception is at night, between midnight and 6:00

AM, when there is less atmospheric interference. To keep your

time as accurate as possible, the weather station conducts a

WWVB search every night between these hours and overrides any

manually set time. The WWVB tower icon (appearing in the TIME

LCD) will flash when a signal-search is in progress, will remain

steady when the signal has been received, and nothing will be

displayed in all other situations. If the WWVB time has not been

received after 10 minutes of battery installation, you may manually

set the time or leave the time function alone (reception will occur

regardless).

B. MANUAL TIME SETTING

1. Press and hold the SET button for 3 seconds or until “12h”

flashes in the DATE LCD.

2. Press the SET button 3 more times (until the hour digit

flashes in the TIME LCD).

3. Press the CH button to change the hour.

4. Press the SET button to confirm the hour setting, and to

advance to the minute setting mode.

5. The minute digits will be flashing. Press the CH button to

change the minutes. Increasing the minutes by increments of 1

with each press of the CH button.

6. Press the SET button to confirm the minutes and to advance to

the Day, Date and Year setting mode.

Note: In 12h mode, “PM” will appear to the left of the time

during PM hours. If the time is not within the PM hours, nothing

will be displayed. Be sure to set the time to the correct AM/PM

time to ensure automatic reception at optimal times.

VI. SETTING THE DAY, DATE, AND YEAR

1. Press and hold the SET button for 3 seconds or until “12 h” or

“24 h” flashes in the DATE LCD.

2. Press the SET button 5 more times to reach the Weekday

setting mode.

Note: “MO” (representing Monday) is the default setting for the

weekday, “1.1” is the default setting for the numeric month and

day and “1999” is the default setting for the year. The day, date

and year will be automatically set once the WWVB signal is

received. However, the day, date and year can be manually set and

will flash respectively in the DATE LCD during manual

programming.

3. The weekday will be flashing in the DATE LCD. Press the

CH button to change the weekday.

4. Press the SET button to confirm and to enter the numeric-

month setting mode.

5. The numeric-month will be flashing in the DATE LCD. Use

the CH button to set to the current month.

6. Press the SET button to confirm the numeric-month and to

enter the numeric-day setting mode.

7. The numeric-day will be flashing. Use the CH button to set

the current day.

8. Press the SET button to confirm and to enter the year setting

mode.

9. The default-year will be flashing. Use the CH to set the

appropriate year.

10. Press the SET button to confirm and to advance to the °F or °C

setting mode.

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-7013U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415V3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1516U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9014 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS 9711 IT+ Installationsanleitung

La Crosse Technology

La Crosse Technology WS-9125TWC-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8120U-IT Installationsanleitung

La Crosse Technology

La Crosse Technology WS9029UITCA Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2811U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9021U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 327-1418BW Bedienungsanleitung

La Crosse Technology

La Crosse Technology KCombo3 WS-9080U-IT WS-9640U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9037U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9029U Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA74962 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-145 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7394U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9049 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7391UD Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7168U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-2513U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 919-186-60WH Abmessungen

La Crosse Technology

La Crosse Technology WS6818 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6826 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung