La Crosse Technology WS-2315CH Bedienungsanleitung

Operation Manual 1. Introduction

Professional Remote Weather Station Thank you for purchasing this Professional Remote Weather Station.

Designed for everyday use, the weather station will prove to be an asset of

great value for your personal use in the home or office. Please read this

instruction manual thoroughly to fully understand the correct operation of your

weather station and benefit from its unique features.

Table of Contents

Page

1. Introduction.................................................................................... 2 2. Intended Use

2. Intended use. ................................................................................. 2

Weather Station. ............................................................................ 2 Weather Station

System requirements for PC use................................................... 2 The base station measures the indoor environment of its surrounding area and

receives weather data from the following three outdoor sensors:

Features of the base station. ......................................................... 3

Features of the thermo-hygro sensor. ........................................... 3 1) Thermo-Hygro Sensor

Features of the wind sensor .......................................................... 3 2) Wind Sensor

Features of the rain sensor............................................................ 3 3) Rain Sensor

3. Safety Notes .................................................................................. 4

4. Packaged contents ........................................................................ 5 The received data is continuously updated to bring you the latest weather

information on the base station’s LCD. The outdoor thermo-hygro sensor is

the main data communication unit since both the wind and rain sensors are

connected to the thermo-hygro sensor for operating power and rely on it to

communicate to the base station. Weather data sent from the thermo-hygro

sensor can be done by wireless 433MHz transmission (up to 100ft in open

space) or by cable connection.

5. Setting up....................................................................................... 6

6. Operation using cable connection or wireless 433MHz................. 9

7. LCD overview .............................................................................. 10

8. Function test ................................................................................ 11

9. Mounting...................................................................................... 12

10. Resetting & factory settings......................................................... 14

11. Function description .................................................................... 16

12. Operation keys ............................................................................ 19 Using the enclosed 6.5ft computer cable and CD-ROM, you can install the

Heavy Weather software to your PC and access the latest weather information

from your PC and upload up to 175 sets of recorded weather data received by

the base station. Recorded data can be used to generate statistics and charts

onto your spreadsheets (175 sets of data is stored in the base even if the PC

is switched OFF). The software itself does not set any limits as to how many

data sets can be transferred to PC.

13. Basic programming modes.......................................................... 21

14. MIN/MAX programming modes ................................................... 22

15. Alarm programming modes ......................................................... 23

16. Auto-memory for stored values ................................................... 30

17. Accessories: extensions cables................................................... 30

18. Changing batteries ...................................................................... 31

19. Problems and interference with operation ................................... 32

20. Transmission range ..................................................................... 33 This weather station is designed to work easily with your PC, simply connect

and disconnect the PC cable at any time.

21. Cleaning and maintenance.......................................................... 33

22. Specifications .............................................................................. 34

23. Warranty Information ................................................................... 36 System Requirements for PC use:

The minimum system requirement for use of this “Heavy Weather” software is:

This Operation Manual is part of this product and should be kept in a

safe place for future reference. It contains important notes on setup and

operation.

Operating system: Windows 98 or above

Processor: Pentium 166 MHz or above

RAM: 32MB of RAM or above

Hard disk: 20MB free space

Please see www.heavyweather.info for a complete IM, FAQ and

downloads of the most current software. CD-ROM drive

For full details on operation and installation of the “Heavy Weather” software

refer to the PC manual in PDF format on the CD-ROM.

Features of the base station: 3. Safety Notes

• Receives and displays the WWVB radio controlled time and date

• Damage caused by failure to comply with this instruction manual will

invalidate any guarantee! The manufacturer and supplier will not be held

liable for damages due to failure to comply with this instruction manual or

from data inaccuracies that may occur with this product!

• Display of extensive weather data, in all cases with programmable alarm

functions for certain weather conditions as well as records of all minimum

and maximum values along with time and date of their recordings

• Indoor and outdoor temperature displays in degrees Fahrenheit or

Celsius (user selectable) • In case of harm or damage to a person or property caused by improper

handling or failure to comply with this instruction manual, the

manufacturer and supplier cannot be held liable.

• Indoor and outdoor relative humidity displays

• Air pressure reading in inHg or hPa, absolute or relative (user selectable)

• For reasons of safety and operation, alterations to this device are strictly

prohibited.

• Detailed display of rainfall data in 1 hour, 24 hours, total since last reset

(user selectable in mm or inch)

• To operate the weather station, use only supplied adaptor and batteries

of the recommended type.

• Wind speed in mph, km/h, m/s, knots or Beaufort (user selectable)

• Wind direction display with LCD compass as well as numerical (e.g. 225°)

and abbreviated characters (e.g. SW) • Do not leave discharged batteries in the device as these may corrode

and release chemicals that may damage the unit.

• Wind chill temperature display

• Inserting batteries in an incorrect polarity will cause damage to this

product.

• Dew point temperature display

• Weather forecast display by weather icons (sunny, cloudy, rainy)

• This product is not a toy. Keep out of the reach of children.

• Weather tendency indicator

• Do not dispose of new or used batteries in a fire as they may explosion or

release dangerous chemicals.

• Storm warning alarm

• LED back light • This product is not to be used for medical purposes or for public

information.

• Simultaneous display of all weather data with individual settings by the

user • Any modification or alteration to this product is strictly prohibited without

the manufacturer’s authorization and may prohibit the user’s further use

of this product.

• COM port for easy connection to your PC

• All the weather data from the base station and up to 175 sets of weather

history data with user adjustable measuring intervals can be recorded

and uploaded to your PC

Features of the Thermo-Hygro Sensor

The thermo-hygro sensor measures the outdoor temperature and relative

humidity. It also collects the readings from the rain and wind sensors before

transmitting the data to the base station by wireless 433MHz or by the 32ft

cable included in this set.

Features of Wind sensor

The wind sensor measures wind speed and wind direction and sends the data

to thermo-hygro sensor, which in turn transmits the data to the base station.

Operating power is taken from the thermo-hygro sensor using a 32ft cable

connection.

Features of Rain sensor

The rain sensor measures the rainfall and sends the data to thermo-hygro

sensor, which in turn transmits the data to the base station. Operating power

is taken from the thermo-hygro sensor by a 32ft cable connection.

4. Packaged Contents 5. Setting up

Before setting up, carefully unpack the contents onto a table or flat surface and

check that the following are complete:

First, choose to use the adaptor (included in this set) or batteries for operation.

Both these methods allow for operation using wireless 433MHz transmission

or cable connection between the base station and the sensors and setting up

for both methods is as follows:

Item: Consisting of: Fittings: Illustration:

Base

Station

• Main unit

• AD/DC 120V power

Adaptor - optional use

(included)

Thermo-

Hygro

Sensor

• Main unit

• Rain protection

cover

• 32ft cable - optional

connection to the base

station (included)

• Wall mounting screws

• Plastic anchors for

screws

Wind

Sensor

• Main unit with

wind vane

• 32ft cable

(already

attached to the

main unit)

• Mast holder

• 2 x U-bolts for mast

holder

• 4 x Washers

• 4 x Nuts

• 1 x screw (to fix main

unit to the mast holder

Rain

Sensor

• Main unit (base

and funnel)

• 32ft cable

(already

attached to the

main unit)

Heavy

weather

software

CD-Rom format

(English version

only)

• 6.5ft PC cable for PC

connection - optional

use (included)

Base Station:

Note: flip open the front panel under the PRESSURE, DISPLAY and WIND

keys to reveal the SET, + (plus), - (minus), ALARM and MIN/MAX operation

keys

Battery

compartment

Socket for Thermo-

Hygro Sensor

Socket for

Ad ptora

PC COM Port

Front Panel

Operation

Keys

1) Pull away the rain cover of the thermo-hygro sensor to reveal the three

sockets (for the wind sensor, rain sensor and the base station)

Setting up using batteries: 2) Connect the attached cables of wind and rain sensors to the

corresponding sockets of the thermo-hygro sensor by clicking them into

place

3) Open the battery cover of the thermo-hygro sensor located below the

three sockets and insert 2 x AA, IEC LR6, 1.5V batteries and close the

cover

4) Open the base station’s battery cover located at the back of the unit and

insert 3 x AA, IEC LR6, 1.5V batteries into the battery compartment and

close the battery cover

Setting up using the AC adaptor:

1) Power up all the sensors as described in setting up using batteries above

2) Using the AC adaptor (included), plug it into the mains outlet and power

up the base station by inserting the adaptor jack into the DC 6.0V socket

located on the side of the base station

Every time the thermo-hygro sensor is powered up (for example after a

change of batteries), a random security code is transmitted and this code must

be synchronized with the base station to receive weather data.

When the base station is powered up, a short beep will sound and all LCD

segments will light up for about 5 seconds before it enters into a 15 minute

learning mode to learn the sensors security code. After the learning mode (or

by pressing the MIN/MAX key at anytime), the base station will start the

WWVB radio controlled time reception.

Note for WWVB Radio Controlled Time:

The time and date display is based on the signal provided by the highly

accurate government operated atomic clock in Ft. Collins, Colorado. This

radio-controlled clock does not only provide for the weather station’s time and

date display but also functions as the time and date source for all of this

weather station’s memory and history values using time and date information.

LCD backlight:

When using the power adaptor, the LCD backlight is switched on continuously.

Under battery operation, the LCD backlight is switched on for 15 seconds

intervals when any key is pressed.

Important: To avoid operating problems, please take note of battery

polarity if inserting any batteries

Sensor sockets

Thermo-Hygro Sensor

Battery Cover

Battery

Compartment

6. Operation using cable connection or wireless 433MHz 7. LCD Overview

Cable Connection: The following illustration shows the full segments of the LCD for

description purposes only and will not appear like this during normal

operation and use.

Using this method of operation will provide interference free transfer of the

weather data from the sensors to the base station. The data sending interval

from the sensors to the base station will also be more frequent compared to

using 433MHz transmission and will result in higher power consumption.

Therefore batteries will have a shorter life span for cable connection compared

to using 433MHz. To operate using cable connection, simply use the enclosed

32ft cable and connect the thermo-hygro sensor to the base station. Once the

connection is detected, the base station will automatically continue reading the

data from the sensor.

The user may at any time switch from cable connection to using 433MHz (or

vice versa) by simply disconnecting (or connecting) the cable from the base

station to the sensor. When the base station detects no cable connection to

the sensors, the base station will automatically change to using 433 MHz for

reception of the weather data from the sensors.

The data receiving intervals are as follows:

- Using cable connection data is updated every 8 seconds.

- Using wireless 433 MHz data is updated from 16 to 128 second intervals

depending on wind speed and rain activity.

Using the AC adaptor to operate the base station will also supply power to the

sensor if the cable is connected to it. Batteries used for 433MHz transmission

may be left in the sensor when using cable connection for power back up in

case of AC power failure. A loss of power would desynchronize the base

station and the sensor and no weather data will be received. To synchronize

the units so that the weather data can be received, press and hold the PLUS

(+) key for 2 seconds. However in general, batteries that will not be used for

long periods should be removed to avoid leakage.

15. 24h, 1h or total hour display

16. Humidity display as RH%

17. Rainfall units (inch or mm)

18. Temperature display units (ºC or ºF)

19. Outdoor temperature/humidity display

20. Indoor temperature/humidity display

21. Dew point temperature display

22. Wind chill temperature display

23. Wind alarm icon

24. Wind information for Min/Max speed

and wind speed low, high, direction

alarm

25. Wind direction and speed (m/s, knots,

Beaufort, km/h or mph) display

26. Alarm buzzer ON/OFF icon

27. General alarm icon

1. Low battery indicator

2. WWVB radio controlled time icon

3. Date display

4. Time zone display

5. Date, seconds, alarm time and time

zone

6. Alarm icon

7. Weather forecast icons

8. Weather tendency indicator

9. Pressure alarm display

10. hPa/inHg air pressure unit

11. Pressure units (relative or absolute)

12. 433MHz reception icon

13. Rainfall display

14. Indoor, outdoor, humidity, dew point,

wind chill, rainfall alarm icon

Wireless 433MHz transmission:

1314

Using 433MHz wireless transmission of weather data from the sensor to the

base station will provide users greater freedom as to where units can be

positioned without the need to be restricted by cable.

Note:

If no outdoor weather data is displayed or the signal to the sensors is lost

during setting up, mounting, changing of batteries to the sensor or plugging or

unplugging cables, simply press and hold the PLUS (+) key for 2 seconds and

a short beep will sound to synchronize the base station to sensors. Without

being synchronized, weather data will not be received.

Base Station

8. Function test With two foldable legs at the back of the unit, the base station can be placed

onto any flat surface or wall mounted at the desired location by the hanging

holes also at the back of the unit. It is important to check that the 433MHz (if

using wireless connection) and the WWVB radio controlled time signal can be

received before permanently mounting any of the units. Should the base

station not display the 433MHz weather data from the sensors or the radio

controlled time from the desired location, then relocate the units. Once the

signals are received, the system can be affixed. Also if you have selected to

use cable connection, ensure that distances can reach all desired locations

before affixing any unit permanently

Once the weather station is powered up, perform a function test by checking

that the weather data is received. To do this, press the DISPLAY,

PRESSURE or WIND keys to toggle through the relevant LCD sections:

1) Indoor temperature and humidity

2) Outdoor temperature and humidity

3) Outdoor wind chill

4) Dew point

5) Rainfall 24 hour

6) Rainfall 1hour

NOTE: For reception of WWVB time/date signal, do not mount the base station

closer than 5 feet from a computer, florescent lights or other electrical

appliances. Do not mount the base station on a wall that has metal heat/AC

ductwork in the wall behind the base station. For best WWVB reception place

the base station near a window facing Colorado. WWVB reception will be

obtained easiest in the nighttime hours when the WWVB signal is strongest.

7) Rainfall Total

8) Relative and absolute pressure

9) Wind speed, wind direction and wind direction in degrees

If any readings cannot be received from the sensors, lines (- - -) will be

displayed in the respective weather sections of the LCD. In this case, check

that all cables are correctly inserted into the correct sockets and/or check the

batteries in the outdoor thermo-hygro sensor and press and hold the PLUS (+)

key for 2 seconds and a short beep will sound to synchronize the base station

to the sensors otherwise no weather data will be received..

Mounting the Wind Sensor onto a mast

Wind-fan

Wind-vane

Mast

Some weather readings such as wind speed and direction may not appear

immediately on the LCD if the wind-fan or vane of the wind sensor is moved.

This is due to the set reading time intervals for the wind readings. However

the current wind speed or direction will be displayed once the time reading

interval is reached. For rainfall, the interval readings may take up to 2 minutes

before the data is displayed on the LCD.

9. Mounting

Important Note

Prior to drilling mounting holes and permanently affixing any of the units,

please ensure the following points are considered:

Firstly, check that the wind-fan and the wind-vane can rotate freely before

fixing the unit. For correct and accurate readings it is important to mount the

sensor so that the front (marked E) is pointing in East-West direction. The

wind sensor should now be mounted using the screw provided onto a mast to

allow the wind to travel around the sensor unhindered from all directions (ideal

mast size should be from Ø0.63” – Ø1.3”).

• Cable lengths of the units meet with your distance requirements at the

point of fixing

• Signals from the sensors can be received by the base station at points of

mounting

• Radio controlled time signal can be received at the point of mounting

NOTE: The WWVB receiver is located in the base station. Once the wind sensor is fixed onto the mast, connect the cable to the

corresponding thermo-hygro sensor socket so that operating power supply can

be received and data can be transmitted to the base station.

Mounting the thermo-hygro Sensor

Mounting the Rain Sensor

For accurate results, the rain sensor should be securely mounted onto a

horizontal surface about 2-3ft above the ground and in an open area away

from trees or other coverings where rainfall may be reduced causing

inaccurate readings.

When securing into place, check that rain excess will not collect and store at

the base of the unit but can flow out between the base and the mounting

surface (test by pouring clean water).

After mounting the rain sensor, connect the cable to the thermo-hygro sensor

at the corresponding socket so power supply can be received and data be

transmitted to the base station

The rain sensor is now operable. For testing purposes, very slowly pour a

small amount of clean water into the rain sensor funnel. The water will act as

rainfall and will be received and displayed at the base station after about 2

minutes delay i.e. when the reading interval is reached (to clear this testing

data on the base station, refer to the section “MIN/MAX Mode” below).

An ideal mounting place for the thermo-hygro sensor would be the outer wall

beneath the extension of a roof, as this will protect the sensor from direct

sunlight and other extreme weather conditions.

To wall mount, use the 2 screws to affix the wall bracket to the desired wall,

plug in the thermo-hygro sensor to the bracket and secure both parts by the

use of the supplied screw and ensure that the cables from the wind and rain

sensors are correctly plugged in otherwise data transmission errors could

occur.

NOTE: For best 433 MHz reception mount the thermo-hygro sensor on an

outside wall near the location of the base station.

10. Resetting & factory settings:

Rain Cover

Wall Bracket

Main Unit

Base portion

Funnel portion

As previously mentioned, in the event of a power reset to the sensor (for

example a change of batteries), the base station has to synchronize to the

sensor again otherwise no weather data will be received. To do this, simply

press and hold the PLUS (+) key for 2 seconds and a short beep will sound to

synchronize the base station to the sensor. When the units are synchronized,

the data will be received again and the base station will return to normal

operation mode.

11. Function Description of the Weather Station

Do not remove batteries or unplug the AC adaptor of the base station

otherwise all 175 sets of recorded weather history data for transferring to the

PC will be lost (for full details of PC use, please see PC user manual in the

enclosed Heavy Weather CD-ROM).

After setting up, the following data will be displayed in different sections on the

LCD. If this is not the case please observe the notes on “Interferences”

below.

However if you wish to make a full reset of the base station and return to the

original factory settings, simultaneously press and hold the PRESSURE and

WIND keys for about 5 seconds. The base station will beep once and the

entire LCD will light up for 5 seconds and go back to the original factory

settings. This process with clear all previous user defined values and all

weather history recordings.

Factory default settings:

The following table shows the factory default values of the weather station:

Matter: Default Setting:

Time 12:00 am

Date 01.01.2001

Time zone -5 ET

Alarm time 12:00 am

Relative air pressure 29.91 inHg

Weather-picture threshold 0.09 inHg

LCD contrast level 5 (1-8 levels)

Rainfall per impulse 0.0204 inches

Storm alarm 0.09 inHg

Relative air pressure alarm 28.34 inHg (low) 30.71 inHg

(high)

Indoor temperature alarm 50ºF (low) 86ºF (high)

Outdoor temperature alarm 32ºF (low) 104ºF (high)

Indoor humidity alarm 35%RH (low) 65%RH (high)

Outdoor humidity alarm 45%RH (low) 70%RH (high)

Wind chill alarm 50ºF (low) 86ºF (high)

Dew point alarm 32ºF (low) 68ºF (high)

Rainfall 24h alarm 1.96 inches

Rainfall 1h alarm 0.03 inches

Wind Speed 1.0 mph (low) 62 mph (high)

Wind direction alarm None set

Time & Date (LCD Section 1)

If the WWVB icon (icon 2) is ON and not flashing, it means that the WWVB

radio-controlled time and date are has been received. Press the PLUS (+) key

to change the format of date display between date/month/year,

weekday/date/month, seconds, alarm set time and time zone.

LCD Section 1:

Time, date, seconds, time zone,

weather forecasting icons with

tendency arrows, air pressure,

and respective alarms sections

LCD Section 2:

Indoor and outdoor temperature and

relative humidity, wind chill, dew

point, rainfall, and respective alarms

sections

LCD Section 3:

Wind direction, wind speed, and

respective alarms sections

Note:

All alarm default values are deactivated at the start up and any alarm must be

activated by the user otherwise it will not sound.

Weather forecasting (LCD Section 1)

Weather Data (LCD Section 2)

The three weather icons Sunny, Cloudy and Rainy represent the weather

forecasting. There are also two weather tendency indicators to show the air

pressure tendency either side of the weather icons.

Indoor temperature and humidity are displayed simultaneously in this section.

Use the DISPLAY key to toggle through the displays for other weather

information:

- Outdoor temperature/humidity

- Outdoor wind chill

- Outdoor dew point

- Rainfall 24h

Sunny Cloudy Rainy

- Rainfall 1h

Notes to inHg sensitivity setting for weather forecasting: - Rainfall total.

The inHg pressure sensitivity can be set to suit the user’s requirement for

weather forecasting from 6 inHg, 9 inHg to 12 inHg (see Basic Programming

below). For areas that experience frequent changes in air pressure (which

does not necessarily reflect a change in the weather) requires a higher inHg

setting compared to an area where the air pressure is stagnant. For example if

6 inHg is selected, then there must be a fall or rise in air pressure of at least 6

inHg before the weather station will register this as a change in weather.

Notes to Dewpoint and Windchill:

Air can at a certain temperature only carry a certain amount of water (water

vapor), which also increases and decreases with temperature. If the air

temperature decreases below the dewpoint (saturation point), the excessive

water vapor will condense and fall out in form of dew, fog or rain. At a

temperature of e.g. 59°F and a relative humidity of 50% the dewpoint will be

about 41°F, at 80% humidity about 53.6°F. At a relative humidity of 100%

saturation is reached, i.e. the dewpoint is 59°F. At a dewpoint below freezing

the fallout will become frost or snow.

Air Pressure (LCD Section 1)

The air pressure reading is displayed here. Press the PRESSURE key to

toggle between relative and absolute air pressure displays.

Windchill has been introduced for battle planning during World War II. It

represents not the real measured but the temperature a person feels in open

area under the influence of wind and cold. Windchill is laid out in tables for

various temperatures and wind speeds. At an outdoor temperature of e.g.

46.4°F and calm winds a person moving at a speed of 13 mph will already feel

a windchill temperature of 32°F.

Notes to Absolute and Relative Air Pressure:

Absolute air pressure provides the display of the true measured air pressure of

the current time and location. This is not programmable and the absolute air

pressure range of the weather station is from 8.85 inHg to 32.45 inHg

(standard air pressure at an altitude of 30,000ft is around 8.85 inHg).

Wind Data (LCD Section 3)

Relative air pressure is the one value that is calculated back to sea level from

the local absolute air pressure and can thus be taken as a reference for

weather condition and weather development for the entire country. It can be

programmed to represent your local surroundings. Since the relative air

pressure is also the one value given by various newspapers, TV and radio

broadcasting stations in their daily weather forecasts for their respective

locations, users can set the relative air pressure of the weather station to this

value to represent readings your their area (see Basic Programming Modes

below).

The current wind direction will be displayed on the LCD compass on the wind

section. Press the WIND key to toggle between wind direction as numerical

(e.g. 225°) and abbreviated characters (e.g. SW) as well as numerical wind

speed display inside the compass circle.

12. Operation keys

The base station has 8 keys for easy operation. Please refer to the following

table for use and function of each key: Further descriptions of the key

functions with regard to their immediate range of application can be found in

the Programming modes:

SET - key - In normal mode to enter the manual basic

programming mode

- In basic programming mode to select the following

setting modes:

- LCD contrast setting

- Manual time setting (hours/minutes)

- 12/24 time format display

- Calendar setting (year/month/date)

- Time zone setting

- °C/°F temperature setting

- Wind speed unit setting

- Rainfall unit setting

- Pressure unit setting

- Relative air pressure setting

- Weather picture threshold setting

- Storm warning setting

- Audible storm alarm setting

- In setting modes confirmation of the selected values

- In alarm modes alarm ON/OFF

- In alarm mode to enter programming of alarm values

(long pressing)

- To exit MIN/MAX modes

PRESSURE

key

- Toggle between Absolute and Relative air pressure

displays

DISPLAY key - Toggle between the following current/ maximum/

minimum display modes:

- Indoor temperature and humidity

- Outdoor temperature and humidity

- Outdoor wind chill

- Outdoor dew point

- Rainfall (24h, 1h, total)

WIND key To toggle between the following settings:

- Wind speed

- Wind direction

- Wind direction display in degrees

ALARM key - In normal mode to enter the alarm programming mode

- In alarm programming mode to select the following

setting modes:

- Time alarm setting

- Indoor temperature alarm (high & low)

- Outdoor temperature alarm (high & low)

- Indoor humidity alarm (high & low)

- Outdoor humidity alarm (high & low)

- Outdoor wind chill alarm (high & low)

- Outdoor dew point alarm (high & low)

- Rainfall alarm (24h, 1h)

- Pressure alarm (high & low)

- Wind speed alarm (high & low)

- Wind direction alarm

- In setting modes confirmation of the selected values

- To exit MIN/MAX modes

- To reset general alarm symbol

MIN/MAX key - In normal display mode to toggle between display of

MIN/MAX values

- To toggle between MIN/MAX values in MIN/MAX

mode

- To exit any programming mode

PLUS (+) key - In normal display mode to toggle between format of

date display, seconds, time alarm and time zone

- To increase the values in the setting modes

- To exit MIN/MAX modes

- In normal display mode to re-enter data learning mode

(long pressing for 2 seconds)

MINUS (-) key - In normal display mode to enable/disable the buzzer

alarm (long pressing)

- To decrease the values in the setting modes

- In basic programming mode audible storm alarm

ON/OFF

- To snooze the alarms off 24 hours when the alarm is

sounding

- In MIN/MAX modes to reset recorded values and

recorded dates and times

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-2010 Bedienungsanleitung

La Crosse Technology

La Crosse Technology S84107 Abmessungen

La Crosse Technology

La Crosse Technology WS-1517 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7015 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417v3 Abmessungen

La Crosse Technology

La Crosse Technology WS-7394U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2310 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9117U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C84343 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 308-1451 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9005TWC-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417BLV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9004U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS9123IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology S77925 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V21V3 Abmessungen

La Crosse Technology

La Crosse Technology WS9090 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8035 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7212U Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9025U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9020U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7044U Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung