La Crosse Technology WS-9210U Bedienungsanleitung

WS-9210U

Wireless 433 MHz

Radio-controlled Temperature Station

Instruction Manual

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 4

Quick Set-Up Guide 5

Detailed Set-Up Guide

Battery Installation 6

Program Mode

Programming Sequence 7

Function Keys 7

12/24 Hour Time Setting 7-8

Time Zone Setting 8

Daylight Saving Time Setting 8-9

Time Setting (WWVB & Manual) 9-10

Setting Day, Date and Year 10

Selecting °F or °C 11

Setting the LCD Contrast 11

Features

Indoor Temperature 12

Outdoor Temperatures 12

Minimum & Maximum Records (Indoor,

Outdoor & Resetting)

Alarm (Setting, Snoozing & Stopping) 14

Additional Remote Temperature Sensor

Units (Set-Up, Viewing & Operation)

14-15

Mounting 16-17

Troubleshooting 18

Maintenance & Care 18

Specifications 19

Warranty Information 19-21

Table Of Contents

INVENTORY OF CONTENTS

1. The weather station (Figure 1).

2. One TX6U remote temperature sensor with mounting bracket (Figure 2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction Manual and Warranty Card.

*LCD = Liquid Crystal Display

ADDITIONAL EQUIPMENT (not included)

1. Two, fresh AA 1.5V batteries for indoor weather station.

2. Two, fresh AA 1.5V batteries for remoter temperature sensor.

3. One, Philips screwdriver for mounting.

Figure 2

Mounting Bracket

Wireless Temperature Sensor

Time LCD

Date LCD

Indoor LCD

Outdoor LCD

ure 1

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency Division)

WWVB radio station is located in Ft. Collins, Colorado and transmits the exact time signal

continuously throughout the United States at 60 kHz. The signal can be received up to 2, 000

miles away through the internal antenna in the weather station. However, due to the nature of

the earth’s ionosphere, reception is very limited during daylight hours. The weather station

will search for a signal every night when reception is best. The WWVB radio station derives

its signal from the NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is

continually measuring every second, of every day, to an accuracy of ten billionths of a second

per day. These physicists have created an international standard measuring a second as

9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

For more information on WWVB and the atomic clock please see the NIST website at

http://www.boulder.nist.gov/timefreq/stations/wwvb.htm.

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor weather station and remote temperature sensor 3 to 5 apart.

2. Batteries should be out of both units.

3. Place the batteries into the remote temperature sensor first then into the

indoor weather station.

(All remote temperature sensors must be started before the indoor weather

station).

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the indoor weather station and remote temperature sensor will start to talk to each

other and the indoor weather station will show both the indoor temperature and an outdoor

temperature. If the indoor weather station does not display both temperatures after the 15

minutes please retry the set up as stated above. After both indoor and outdoor temperatures

are displayed for 15 minutes you can place your remote temperature sensor outdoors and set

your time.

The remote temperature sensor should be placed in a dry, shaded area. The remote

temperature sensor has a range of 80 feet. Any walls that the signal will have to pass through

will reduce distance. An outdoor wall or window can have up to 30 feet of resistance and an

interior wall can have up to 20 feet of resistance depending upon the type of construction.

Your distance plus resistance should not exceed 80 ft. in a straight line.

NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be

avoided.

To complete the set up of your indoor weather station after the 15 minutes have passed please

follow the steps on pages 8 and 9.

Note: The remote temperature sensor transmits a signal every 3 minutes; after the

batteries have been installed, the indoor weather station will search for the signal

for a duration of 5 minutes. If there is no temperature reading in the OUTDOOR

LCD after 5 minutes, make sure the units are within range of each other or repeat

the battery installation procedure.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket. The bracket

snaps on and off easily.

2. Remove the battery cover, by sliding the

cover down.

3. Observing the correct polarity install 2 AA

batteries. The batteries will fit tightly (to

avoid start-up problems make sure they do

not spring free).

4. Replace the battery cover by sliding

upwards. Be sure battery cover is on

securely.

B. INDOOR WEATHER STATION

1. Remove the battery cover. To do this,

insert a solid object in the space

provided at the lower-central position

of the battery cover, then push up and

pull out on the battery cover.

2. Observe the correct polarity, and

install 2 AA batteries.

3. Replace the battery cover.

Note: Immediately after the batteries have been installed, each LCD

(Liquid Crystal Display) will flash and a tone will sound. Within a few

seconds the indoor temperature will be displayed. If not, then remove the

batteries for 10 seconds and reinstall. If the outdoor temperature is not

displayed within four minutes, remove batteries from both units, wait 10

seconds, and reinstall. The time will show -:-- and start searching for the

WWVB signal. If it successfully receives the time signal (usually at night),

it will display the correct time (default is Eastern).

PROGRAM MODE

Programming Note: If 30 seconds are allowed to pass or either the IN or the OUT

button is pressed during programming modes, the unit will set the last information

entered—the display will stop flashing and return to normal time-date readings. If

you don’t leave the program mode during the programming of sections III through

IX, you can advance to step 3 of the next program setting. If you do leave the

program setting (or want to program a specific setting) follow each instructional

step to program that setting.

I. PROGRAMMING SEQUENCE

The sequence for programming the indoor weather station and the default (factory)

settings are:

1. 12/24 hour time setting 12 hour

2. Time Zone Zo -5 (eastern)

3. Daylight Saving Time 1 (on)

4. Time – hour 12

5. Time – minute 00

6. Date – day of the week mo (Monday)

7. Date – month 1 (January)

8. Date – day of the month 1

9. Date – Year 1999

10. Temperature °F

11. LCD (liquid crystal display) contrast 5

12. End of sequence

The programming instructions are given in a manner so that each setting is done

separately. On initial set-up and after inserting new batteries to program all

functions simply disregard the first two steps of each section starting with the Time

Zone Setting.

II. FUNCTION KEYS

The function keys are operated by pressing the key

corresponding to the operation that you want to perform.

III. 12 OR 24 HOUR TIME SETTING

1. Press and hold the “SET” button for 3 seconds or until “12 h” flashes

in the DATE LCD.

2. Press and release the “CH” button to toggle between 12 and 24-hour

time.

3. Press and release the “SET” button to confirm the 12/24-hour setting

and to advance to Time Zone Setting.

IV. TIME ZONE SETTING

The default time zone is EST, “Zo -5” (Eastern

Standard Time), to change this setting:

1. Press and hold the “SET” button for 3

seconds or until “12 h” OR “24 h” flashes

in the DATE LCD.

2. Press and release the “SET” button 1 more time to enter the Time

Zone setting mode.

3. The default Time Zone “Zo-5” will flash in the DATE LCD.

4. Select your appropriate time

zone using the “CH” button.

During selection of the Time

Zone, the 3 letter

abbreviations for the time

zones found in North

America will flash across the

top of the TIME LCD.

Observe the chart below,

showing the corresponding

abbreviations, time zones,

and codes.

5. Press and release the “SET”

button to confirm and advance to the Daylight Saving Time setting.

V. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the “SET” button for 3

seconds or until “12 h” or “24 h” flashes

in the DATE LCD.

2. Press and release the “SET” button 2

more times to reach the DST selection

mode.

3. “DST 1” is the default setting and will be flashing in the DATE

LCD.

4. Press and release the “CH” button to select “DST 0” or “DST 1.”

5. “DST 0” indicates that the feature is off and the WWVB will not

change times automatically. “DST 1” indicates that the feature is on

and the WWVB will change times automatically.

Time Zones

GMT 0

Atlantic -4

EST; Eastern -5

CST; Central -6

MST; Mountain -7

PST; Pacific -8

ALA; Alaska -9

HAW; Hawaii -10

Note: Some locations (Arizona and parts of Indiana) do not follow

Daylight Saving Time and should select “DST 0.”

6. Press and release the “SET” button to confirm and advance to the

Time setting mode.

VI. TIME

There are two methods by which the time can be set:

A) Automatically via WWVB reception or

B) Manually.

A. WWVB (Remote Control Time)

This method requires you to do nothing except wait for the signal to be

received and to select a time zone. Reception usually takes approximately

6-10 minutes during optimal conditions. The best conditions for reception

is at night, between midnight and 6:00 AM—when there is less

atmospheric interference. To keep your time as accurate as possible, the

weather station conducts a WWVB search every night between these

hours and overrides any manually set time. The WWVB tower icon

(appearing in the TIME LCD) will flash when a signal-search is in

progress, will remain steady when the signal has been received and

nothing will be displayed in all other situations. If the WWVB time has

not been received after 10 minutes of battery installation, you may

manually set the time or leave the time function alone (once reception has

occurred the WWVB time will over ride the manual time and set

automatically).

B. MANUAL TIME SETTING

1. Press and hold the “SET” button for 3 seconds or until “12h”

flashes in the DATE LCD.

2. Press and release the “SET” button 3 more times.

3. The hour digit (default of “12” should be flashing in the TIME

LCD).

4. Press and release the “CH” button to change the hour. Press the

“CH” button once and the hour will increase by one, twice and the

hour will increase by two, etc.

5. Press and release the “SET” button to confirm the hour setting and

to advance to the minute setting mode.

6. The minute digits should be flashing. Press and release the "CH”

button to change the minutes—increasing the minutes by

increments of 1 with each press of the “CH” button.

7. Press and release the “SET” button to confirm the minutes and to

advance to the Day, Date, and Year setting mode.

Note: In 12h mode, “PM” will appear to the left of the time during PM

hours. If the time is not within the PM hours, nothing will be displayed.

Be sure to set the time to the correct AM/PM time to ensure automatic

reception at optimal times.

VII. SETTING THE DAY, DATE, AND YEAR

1. Press and hold the “SET” button for 3 seconds, or until “12 h” or “24

h” flashes in the DATE LCD.

2. Press and release the “SET” button 5 more times to reach the

Weekday setting mode.

Note: “MO” (representing Monday) is the default setting for the

weekday, “1.1” is the default setting for the numeric month and day, and

“1999” is the default setting for the year. The day, date, and year will be

automatically set once the WWVB signal is received. However, the day,

date, and year can be manually set and will flash respectively in the

DATE LCD during manual programming.

3. The weekday will be flashing in the

DATE LCD, press and release the

“CH” button to change the weekday.

4. Press and release the “SET” button

to confirm, and to enter the numeric-

month setting mode.

5. The numeric-month will be flashing in

the DATE LCD. Press and release the

“CH” button to select to the current

month.

6. Press and release the “SET” button to confirm the numeric-month,

and to enter the numeric-day setting mode.

7. The numeric-day will be flashing,

press and release the “CH” button to

select the current day.

8. Press and release the “SET” button to

confirm and to enter the year setting

mode.

9. The default-year will be flashing, press and release the “CH” to

select the appropriate year.

10. Press and release the “SET” button to confirm and to advance to the

°F or °C setting mode.

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology 327-1417BW Abmessungen

La Crosse Technology

La Crosse Technology WS-7059U4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7208U Bedienungsanleitung

La Crosse Technology

La Crosse Technology TX231RW Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1517 Abmessungen

La Crosse Technology

La Crosse Technology WS-7026U Bedienungsanleitung

La Crosse Technology

La Crosse Technology V21-WTH Konfigurationshandbuch

La Crosse Technology

La Crosse Technology WS-9009U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2315AL Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9018U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WEATHER DIRECT WD-3103U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1409BT Bedienungsanleitung

La Crosse Technology

La Crosse Technology W85777 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS9245 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9031U Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6835 Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA73453B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8610U Bedienungsanleitung

La Crosse Technology

La Crosse Technology Outdoor Sensor Handbuch

La Crosse Technology

La Crosse Technology WS-2814U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9740U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9025U Handbuch

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung