Labconco Protector 3410000 Bedienungsanleitung

ProtectorDowndraft

Powder Stations

Models

3410000 3410001

3410020 3410021 3410022

3410023 3410024 3410025

Labconco Corporation reserves the right to make periodic design changes without obligation to

notify any person or entity of such change.

Returned or Damaged Goods

Do not return goods without the prior authorization from Labconco. Unauthorized returns will not

be accepted. If your shipment was damaged in transit, you must file a claim directly with the

freight carrier. Labconco Corporation and its dealers are not responsible for shipping damages.

The United States Interstate Commerce Commission rules require that claims be filed with the

delivery carrier within fifteen (15) days of delivery.

Limitation of Liability

The disposal and/or emission of substances used in connection with this equipment may be

governed by various federal, state, or local regulations. All users of this equipment are required

to become familiar with any regulations that apply in the user’s area concerning the dumping of

waste materials in or upon water, land, or air and to comply with such regulations. Labconco

Corporation is held harmless with respect to user’s compliance with such regulations.

Contacting Labconco Corporation

If you have questions that are not addressed in this manual, or if you need technical assistance,

contact Labconco’s Customer Service Department or Labconco’s Product Service Department at

1-800-821-5525 or 1-816-333-8811, between the hours of 7:30 a.m. and 5:30 p.m., Central

Standard Time.

Part #3412800, Rev. E

ECO L627

Warranty

Labconco Corporation provides a warranty to the original buyer for the repair or replacement

of parts and reasonable labor as a result of normal and proper use of the equipment with

compatible chemicals. Broken glassware and maintenance items, such as filters, gaskets,

light bulbs, finishes and lubrication are not warranted. Excluded from warranty are products

with improper installation, erratic electrical or utility supply, unauthorized repair and products

used with incompatible chemicals.

The warranty for Protector®Downdraft Powder Stations will expire one year from date of

installation or two years from date of shipment from Labconco, whichever is sooner. Warranty

is non-transferable and only applies to the owner (organization) of record.

Buyer is exclusively responsible for the set-up, installation, verification, decontamination or

calibration of equipment. This limited warranty covers parts and labor, but not transportation

and insurance charges. If the failure is determined to be covered under this warranty, the

dealer or Labconco Corporation will authorize repair or replacement of all defective parts to

restore the unit to operation. Repairs may be completed by 3rd party service agents approved

by Labconco Corporation. Labconco Corporation reserves the rights to limit this warranty

based on a service agent’s travel, working hours, the site’s entry restrictions and unobstructed

access to serviceable components of the product.

Under no circumstances shall Labconco Corporation be liable for indirect, consequential, or

special damages of any kind. This warranty is exclusive and in lieu of all other warranties

whether oral, or implied.

CHAPTER 1: INTRODUCTION 1

CHAPTER 2: PREREQUISITES 2

Space Requirements 2

Clearance 2

Location Requirements 2

Exhaust Requirements 3

Electrical Requirements 3

CHAPTER 3: GETTING STARTED 4

Unpacking the Station 4-6

CHAPTER 4: PERFORMANCE FEATURES AND SAFETY

PRECAUTIONS 7

Directional Airflow 8

Prefilter 8

HEPA Filter 8-9

Blower 9

Station Air Intake and Exhaust 9

Safety Precautions 10-11

CHAPTER 5: USING THE STATION 12

Fan Switch 12

Filter System Light 12

Dusting in the Station 13

CHAPTER 6: MAINTAINING THE STATION 14

Routine Maintenance Schedule 14

Service Operations 15-17

Prefilter Replacement 15

HEPA Filter Replacement 16

Resetting a Circuit Breaker 17

CHAPTER 7: TROUBLESHOOTING 18

APPENDIX A: COMPONENTS 19

APPENDIX B: DIMENSIONS 20

APPENDIX C: SPECIFICATIONS 21

APPENDIX D: ACCESSORIES 22

Product Service 1-800-522-7658

Congratulations on the purchase of a Labconco Protector Downdraft

Powder Station. The Station is designed to capture and collect fingerprint

powder to prevent its spread in the room environment and on you while

dusting for prints. The Protector Station is the result of years of experience

in manufacturing laboratory equipment, and users like you suggested

many of its features to us.

The Downdraft Powder Station offers many unique features to enhance

performance and flexibility. To take full advantage of them, please

acquaint yourself with this manual and keep it handy for future reference.

If you are unfamiliar with how downdraft stations operate, please review

Chapter 4: Performance Features and Safety Precautions before you

begin using the station. Even if you are an experienced station user,

please review Chapter 5: Using the Station; it describes the station’s

features so that you can use it efficiently.

This manual and other technical information is available in PDF

format at our website: www.labconco.com.

Product Service 1-800-522-7658

Before you install the downdraft station, you need to plan the site for

installation. Examine the location where you intend to install the station.

You must be certain that the area is level and of solid construction. In

addition, a source of electrical power must be located near the installation

site.

Carefully read this chapter to learn:

Space requirements.

Location requirements.

Electrical power requirements.

Exhaust requirements.

Refer to Appendix C: Specifications, for complete station electrical and

environmental conditions, specifications and requirements.

Space Requirements

The dimensions for the downdraft station are shown in Appendix B:

Dimensions.

Clearance

A minimum clearance of at least 6 inches (150 mm) is suggested on the

top of the station to allow for the unobstructed discharge of filtered air.

Location Requirements

Note: The station should be located on a flat, level bench or work surface

for proper operation.

Chapter 2: Prerequisites

Product Service 1-800-522-7658

Exhaust Requirements

As stated earlier, the exhaust discharge of the station, located on the

upper left side on the back of the station should never be obstructed. The

station is designed to have its back surface pushed against a wall, but the

top of the station should have no obstructions within 6 inches of the

exhaust discharge.

Electrical Requirements

The Downdraft Station models have the following electrical requirements:

Model #

Requirements

3410000-01

115 VAC, 60 Hz, 1 Amp

3410020-25

230 VAC, 50/60 Hz, 0.5 Amp

Note: An outlet with a circuit breaker rated at 10 amps for 115 volt

models (5 amps for 230 volt models) should be located as close as

possible to the right rear side of the station. Power cords supplied

with the station are 3 meters (10 feet) long.

Table 2-1

Product Service 1-800-522-7658

Now that the installation site is properly planned, you are ready to inspect

and install the Protector Downdraft Powder Station. This chapter covers

how to:

Unpack the station.

Install the station.

Connect the electrical supply source.

Tools required for installation the station include a flat-blade screwdriver,

scissors, or a box knife.

Note: The station can weigh up to 75 lbs. (34 kg). Always follow safe-

lifting guidelines when unpacking or moving the station.

Unpacking the Station

Carefully remove the outer carton and inspect the station for damage that

may have occurred in transit. If the station is damaged, notify the delivery

carrier immediately and retain the entire shipment intact for inspection by

the carrier.

Note: United States Interstate Commerce Commission rules require that

claims be filed with the delivery carrier within fifteen (15) days of delivery.

Do not return goods without the prior authorization of Labconco.

Unauthorized returns will not be accepted.

If the station was damaged in transit, you must file a claim directly with the

freight carrier. Labconco Corporation and its dealers are not responsible

for shipping damages.

Do not discard the carton or packing material for the station until all of the

components have been checked, installed and tested.

Chapter 3: Getting Started

Product Service 1-800-522-7658

The work surface and work surface pan are shipped unassembled to the

filter module. To assemble the station:

1) Engage the notches on the front of the pan with the pins located in

the bottom corners of the filter module, as shown in Figure 3-1.

Engage the work surface pan

With the lower pins on the side

of the filter module.

2) Set the work surface on top of the pan by hooking the rear flange

under Ensure the work surface flange goes behind the front panel

the bottom edge of the filter cover, as shown in Figure 3-2.

Figure 3-1

Figure 3-2

Ensure the work surface

flange goes behind the

front panel.

Chapter 3: Getting Started

Product Service 1-800-522-7658

3) Install both side shields by engaging the notches in each panel into the

gap between the front panel and the filter module. Ensure the side panel

pin engages the oversized holes on the edges of the work surface.

4) Plug the power cord into the filter module. The plug socket is located on

the top right rear corner of the station. The unit is ready for use.

Figure 3-3

Ensure the pins

go into the

oversized

holes.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Labconco Laborausrüstung Handbücher

Labconco

Labconco Capture BT 31700-00 Bedienungsanleitung

Labconco

Labconco CentriVap 78110-00 Bedienungsanleitung

Labconco

Labconco Purifier Class 2 Biological Safety Cabinet Bedienungsanleitung

Labconco

Labconco Precise 5220100 Bedienungsanleitung

Labconco

Labconco FreeZone 70020 Series Bedienungsanleitung

Labconco

Labconco RapidStill I Bedienungsanleitung

Labconco

Labconco Logic+ A2 Bedienungsanleitung

Labconco

Labconco FreeZone 7750000 Bedienungsanleitung

Labconco

Labconco Protector Premier 10040 Series Bedienungsanleitung

Labconco

Labconco 44003 Series Bedienungsanleitung

Labconco

Labconco RapidVap 73200 Series Bedienungsanleitung

Labconco

Labconco FreeZone Plus Bedienungsanleitung

Labconco

Labconco CentriVap 73100 Series Bedienungsanleitung

Labconco

Labconco FreeZone 70061 6L -50C Series Bedienungsanleitung

Labconco

Labconco Protector XL 1124 Series Bedienungsanleitung

Labconco

Labconco FreeZone Triad 74000 Series Bedienungsanleitung

Labconco

Labconco Protector Echo 180 Series Bedienungsanleitung

Labconco

Labconco Protector 3390000 Bedienungsanleitung

Labconco

Labconco CentriVap-105 Cold Trap Bedienungsanleitung

Labconco

Labconco Protector XL 1110 Series Bedienungsanleitung

Labconco

Labconco Purifier Logic+ 30231 Bedienungsanleitung

Labconco

Labconco Protector 1204 Series Bedienungsanleitung

Labconco

Labconco Purifier 3951400 Bedienungsanleitung

Labconco

Labconco FreeZone 6 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung