Labconco Protector XStream 9840400 Bedienungsanleitung

Protector®XStream®

Laboratory Fume Hoods

User’s Manual

LABCONCO CORPORATION

8811 PROSPECT AVENUE

KANSAS CITY, MO 64132-2696

800-821-5525, 816-333-8811

FAX 816-363-0130

E-MAIL [email protected]

HOME PAGE www.labconco.com

Labconco’s Mascot,

Labby the LABster

www.labconco.com/productreg.html

or return the attached card and

receive FREE LabbyWear™!

Models

9840400, 9840401, 9840402, 9840403,

9840500, 9840501, 9840502, 9840503,

9840600, 9840601, 9840602, 9840603,

9840800, 9840801, 9840802, 9840803

Product designs are subject to change without notice

Printed in U.S.A.

Labconco Corporation

8811 Prospect Avenue

Kansas City, Missouri 64132

The information contained in this manual and the accompanying product is copyrighted and all rights are

reserved by Labconco Corporation. Labconco Corporation reserves the right to make periodic design

changes without obligation to notify any person or entity of such change.

Protector® XStream® Laboratory Fume Hood Manual #9825000

Warranty

Labconco provides a warranty on all parts and factory workmanship. The warranty includes areas of

defective material and workmanship, provided such defect results from normal and proper use of the

equipment.

The warranty for all Labconco products will expire one year from date of installation or two years from

date of shipment from Labconco, whichever is sooner, except the following:

• Purifier® Delta® Series Biological Safety Cabinets, and PuriCare™ Bedding Disposal Stations

carry a three-year warranty from date of installation or four years from date of shipment from

Labconco, whichever is sooner.

• Carts carry a lifetime warranty.

• Glass is not warranted from breakage due to accident or mishandling.

This limited warranty covers parts and labor, but not transportation and insurance charges. In the event of a

warranty claim, contact Labconco Corporation or the dealer who sold you the product. If the cause is

determined to be a manufacturing fault, the dealer or Labconco Corporation will repair or replace all

defective parts to restore the unit to operation. Under no circumstances shall Labconco Corporation be

liable for indirect, consequential, or special damages of any kind. This statement may be altered by a

specific published amendment. No individual has authorization to alter the provisions of this warranty

policy or its amendments. Lamps and filters are not covered by this warranty. Damage due to corrosion or

accidental breakage is not covered.

Limitation of Liability

The disposal and/or emission of substances used in connection with this equipment may be governed by

various federal, state, or local regulations. All users of this equipment are required to become familiar with

any regulations that apply in the user’s area concerning the dumping of waste materials in or upon water,

land, or air and to comply with such regulations. Labconco Corporation is held harmless with respect to

user’s compliance with such regulations.

Contacting Labconco Corporation

If you have questions that are not addressed in this manual, or if you need technical

assistance, contact Labconco’s Customer Service Department or Labconco’s Product

Service Department at 1-800-821-5525 or 1-816-333-8811, between the hours of 7:00

a.m. and 6:00 p.m., Central Standard Time.

Visit Labconco’s web site at: http://www.labconco.com or email Labconco at: [email protected].

Part #9825000 Rev B, ECO C299

Product designs are subject to change without notice

Printed in U.S.A.

☞

CHAPTER 1: INTRODUCTION 1

About This Manual 2

Typographical Conventions 3

YourNextStep 4

CHAPTER 2: PREREQUISITES 5

Location Requirements 6

Support Requirements 6

Exhaust Requirements 6

Exhaust Requirements Table 7

ElectricalRequirements 7

Service Line Requirements 8

Space Requirements 8

CHAPTER 3: GETTING STARTED 9

Unpacking Your Fume Hood 10

Removing the Shipping Skid 10

SashWeightRelease 11

Installing the Hood on a Supporting Structure & Work Surface 11

Connecting to the Hood Exhaust System 13

Connecting the Electrical Supply Source 14

Connecting the Service Lines 15

Sealing the Protector Hood 16

Certifying the Protector Fume Hood 17

CHAPTER 4: HIGH PERFORMANCE FEATURES AND SAFETY

PRECAUTIONS 19

High Performance Features 19

Safety Precautions 24

CHAPTER 5: USING YOUR PROTECTOR 27

Operating the Vertical Rising Sash 27

Operating the A-Style Combination Sash 27

OperatingtheBlower 28

OperatingtheLights 28

Working in your Protector Fume Hood 28

CHAPTER 6: MAINTAINING YOUR FUME HOOD 31

Routine Maintenance Schedule 31

RoutineServiceOperations 32

CHAPTER 7: MODIFYING YOUR FUME HOOD 33

Installing Work Surfaces 33

Installing Ceiling Enclosures above the Fume Hood 34

Installing Rear Panels behind the Fume Hood 34

Installing Additional Service Fixtures 34

Installing Guardian Digital Airflow Monitor 35

Distillation Grids – Field Installation 35

Installing an Electrical Duplex Outlet 36

CHAPTER 8: TROUBLESHOOTING 37

APPENDIX A: PROTECTOR XSTREAM COMPONENTS 41

APPENDIX B: PROTECTOR XSTREAM DIMENSIONS 45

APPENDIX C: PROTECTOR XSTREAM SPECIFICATION 47

APPENDIX D: REFERENCES 53

DECLARATION OF CONFORMITY 57

Product Service 1-800-522-7658

Congratulations on your purchase of a Labconco Protector®

XStream® Laboratory Fume Hood. Your Protector XStream

Laboratory Fume Hood is designed to protect you by providing

superior containment while conserving energy at OSHA approved

“low flow” velocities as low as 60 feet per minute. It is the result

of Labconco’s commitment to developing a high performance

fume hood and more than 50 years experience in manufacturing

fume hoods.

The Labconco Protector XStream Fume Hood has been engineered

to provide maximum containment in a laboratory, and effectively

contain toxic, noxious, or other harmful materials when properly

installed. The Protector XStream offers many unique features to

enhance safety, performance, and energy savings. To take full

advantage of them, please acquaint yourself with this manual and

keep it handy for future reference. If you are unfamiliar with how

high performance fume hoods operate, please review Chapter 4:

High Performance Features and Safety Precautions before you

begin working in the fume hood. Even if you are an experienced

fume hood user, please review Chapter 5: Using Your Fume Hood,

which describes your Protector XStream Hood’s features so that

you can use the hood efficiently.

2 Product Service 1-800-522-765

Chapter 1: Introduction

About This Manual

This manual is designed to help you learn how to install, use, and

maintain your laboratory fume hood. Instructions for installing

optional equipment on your hood are also included.

Chapter 1: Introduction provides a brief overview of the

laboratory fume hood, explains the organization of the manual, and

defines the typographical conventions used in the manual.

Chapter 2: Prerequisites explains what you need to do to prepare

your site before you install your laboratory fume hood. Electrical

and service requirements are discussed.

Chapter 3: Getting Started contains the information you need to

properly unpack, inspect, install, and certify your laboratory fume

hood.

Chapter 4: High Performance Features and Safety Precautions

explains how the Protector XStream operates and the appropriate

precautions you should take when using the fume hood.

Chapter 5: Using Your Protector XStream discusses the basic

operation of your fume hood. Information on how to prepare, use

and shut down your Protector XStream Hood are included.

Chapter 6: Maintaining Your Protector XStream explains how to

perform routine maintenance on your fume hood.

Chapter 7: Modifying Your Protector XStream explains how to

modify the fume hood or add accessories.

Chapter 8: Troubleshooting contains a table of problems you may

encounter while using your laboratory fume hood including the

probable causes of the problems and suggested corrective actions.

Appendix A: Protector XStream Hood Components contains

labeled diagrams of all of the components of the fume hoods.

Appendix B: Protector XStream Hood Dimensions contains

comprehensive diagrams showing all of the dimensions for the

laboratory fume hoods.

Product Service 1-800-522-7658

Chapter 1: Introduction

Appendix C: Protector XStream Hood Specifications contains the

electrical requirements for laboratory fume hood. Wiring diagrams

are also included.

Appendix D: References lists the various resources available that

deal with laboratory fume hoods.

Typographical Conventions

Recognizing the following typographical conventions will help

you understand and use this manual:

• Book, chapter, and section titles are shown in italic type (e.g.,

Chapter 3: Getting Started).

• Steps required to perform a task are presented in a numbered

format.

• Comments located in the margins provide suggestions,

reminders, and references.

• Critical information is presented in boldface type in paragraphs

that are preceded by the exclamation icon. Failure to comply

with the information following an exclamation icon may result

in injury to the user or permanent damage to fume hood.

• Critical information is presented in boldface type in paragraphs

that are preceded by the wrench icon. These operations should

only be performed by a trained certifier or contractor. Failure

to comply with the information following a wrench icon may

result in injury to the user or permanent damage to your hood.

• Important information is presented in capitalized type in

paragraphs that are preceded by the pointer icon. It is

imperative that the information contained in these paragraphs

be thoroughly read and understood by the user.

• A number icon precedes information that is specific to a

particular model of laboratory fume hood. The 4' icon

indicates the text is specific to the 4-foot wide model. The 5'

icon indicates the text is specific to the 5-foot model, etc.

• The S icon indicates the text is specific to the standard model.

• The A icon indicates the text is specific to the A-Style

Combination Sash Model.

☞

4' 5' 6'

4 Product Service 1-800-522-765

Chapter 1: Introduction

Your Next Step

If your Fume Hood needs to be installed, proceed to Chapter 2:

Prerequisites to ensure your installation site meets all of the

requirements. Then, go to Chapter 3: Getting Started for

instructions on how to install your laboratory fume hood and make

all of the necessary connections.

If you would like to review how Labconco’s high performance

laboratory fume hoods operate, go to Chapter 4: High

Performance Features and Safety Precautions.

For information on the operational characteristics of your

laboratory fume hood, go to Chapter 5: Using Your Protector

XStream Hood.

If your laboratory fume hood is installed and you need to perform

routine maintenance on the cabinet, proceed to Chapter 6:

Maintaining Your Protector XStream Hood.

For information on making modifications to the configuration of

your fume hood, go to Chapter 7: Modifying Your Laboratory

Fume Hood.

Refer to Chapter 8: Troubleshooting if you are experiencing

problems with your fume hood.

Product Service 1-800-522-7658

Before you install your laboratory fume hood, you need to prepare

your site for installation. Carefully examine the location where

you intend to install your hood. You must be certain that the area

is level and of solid construction. In addition, a dedicated source

of electrical power must be located near the installation site.

Carefully read this chapter to learn the requirements for your

installation site:

• The location requirements.

• The support requirements.

• The exhaust requirements.

• The electrical power requirements.

• The service line requirements.

• The space requirements.

Refer to Appendix B: Protector XStream Hood Dimensions for

complete fume hood dimensions.

Refer to Appendix C: Protector XStream Hood Specifications for

complete laboratory fume hood electrical and environmental

conditions, specifications and requirements.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Labconco Laborausrüstung Handbücher

Labconco

Labconco Fiberglass 30 Series Bedienungsanleitung

Labconco

Labconco Capture BT 31700-00 Bedienungsanleitung

Labconco

Labconco CApture 3420000 Bedienungsanleitung

Labconco

Labconco Protector 3390000 Bedienungsanleitung

Labconco

Labconco RapidVap 73200 Series Bedienungsanleitung

Labconco

Labconco CentriVap-105 Cold Trap Bedienungsanleitung

Labconco

Labconco CentriVap Complete 73150 Series Bedienungsanleitung

Labconco

Labconco Protector 3410000 Bedienungsanleitung

Labconco

Labconco CentriVap DNA Systems Bedienungsanleitung

Labconco

Labconco Purifier Axiom 30441 Series Bedienungsanleitung

Labconco

Labconco FreeZone Plus Bedienungsanleitung

Labconco

Labconco 44003 Series Bedienungsanleitung

Labconco

Labconco Logic+ A2 Bedienungsanleitung

Labconco

Labconco Precise CA 5220100 Bedienungsanleitung

Labconco

Labconco FreeZone Triad 74000 Series Bedienungsanleitung

Labconco

Labconco CentriVap 78110 Series Bedienungsanleitung

Labconco

Labconco Purifier Class 2 Biological Safety Cabinet Bedienungsanleitung

Labconco

Labconco Capture BT 31700-00 Bedienungsanleitung

Labconco

Labconco Axiom C1 Bedienungsanleitung

Labconco

Labconco Purifier 3951400 Bedienungsanleitung

Labconco

Labconco FreeZone 7750000 Bedienungsanleitung

Labconco

Labconco FreeZone 6 Bedienungsanleitung

Labconco

Labconco FreeZone 70061 6L -50C Series Bedienungsanleitung

Labconco

Labconco Protector Echo 180 Series Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung