Labconco Protector 3390000 Bedienungsanleitung

ProtectorBenchtop Evidence

Drying Cabinets

Models

3390000

3390001

Corporation reserves the right to make periodic design changes without obligation to notify any person

or entity of such change.

Returned or Damaged Goods

Do not return goods without the prior authorization from Labconco. Unauthorized returns will not be

accepted. If your shipment was damaged in transit, you must file a claim directly with the freight

carrier. Labconco Corporation and its dealers are not responsible for shipping damages.

The United States Interstate Commerce Commission rules require that claims be filed with the delivery

carrier within fifteen (15) days of delivery.

Limitation of Liability

The disposal and/or emission of substances used in connection with this equipment may be governed by

various federal, state, or local regulations. All users of this equipment are required to become familiar

with any regulations that apply in the user’s area concerning the dumping of waste materials in or upon

water, land, or air and to comply with such regulations. Labconco Corporation is held harmless with

respect to user’s compliance with such regulations.

Contacting Labconco Corporation

If you have questions that are not addressed in this manual, or if you need technical assistance, contact

Labconco’s Customer Service Department or Labconco’s Product Service Department at 1-800-821-

5525 or 1-816-333-8811, between the hours of 7:30 a.m. and 5:30 p.m., Central Standard Time.

Part #3390700, Rev. D

ECO L479

Warranty

Labconco Corporation provides a warranty to the original buyer for the repair or replacement of

parts and reasonable labor as a result of normal and proper use of the equipment with compatible

chemicals. Broken glassware and maintenance items, such as filters, gaskets, light bulbs, finishes

and lubrication are not warranted. Excluded from warranty are products with improper

installation, erratic electrical or utility supply, unauthorized repair and products used with

incompatible chemicals.

The warranty for Protector®Benchtop Evidence Drying Cabinets will expire one year from date

of installation or two years from date of shipment from Labconco, whichever is sooner. Warranty

is non-transferable and only applies to the owner (organization) of record.

Buyer is exclusively responsible for the set-up, installation, verification, decontamination or

calibration of equipment. This limited warranty covers parts and labor, but not transportation and

insurance charges. If the failure is determined to be covered under this warranty, the dealer or

Labconco Corporation will authorize repair or replacement of all defective parts to restore the unit

to operation. Repairs may be completed by 3rd party service agents approved by Labconco

Corporation. Labconco Corporation reserves the rights to limit this warranty based on a service

agent’s travel, working hours, the site’s entry restrictions and unobstructed access to serviceable

components of the product.

Under no circumstances shall Labconco Corporation be liable for indirect, consequential, or

special damages of any kind. This warranty is exclusive and in lieu of all other warranties

whether oral, or implied.

CHAPTER 1: INTRODUCTION 1

CHAPTER 2: PREREQUISITES 2

Space Requirements 2

Clearance 2

Location Requirements 3

Exhaust Requirements 3

Electrical Requirements 3

CHAPTER 3: GETTING STARTED 4

Unpacking the cabinet 4

Preparing the Evidence Drying Cabinet for Operation 5

Initial Operation 6

CHAPTER 4: PERFORMANCE FEATURES AND SAFETY

PRECAUTIONS 7

Directional Airflow 8

Optional Evidence Prefilters 9

Prefilters 9

HEPA Filters 9

Blower 10

Cabinet Air Intake and Exhaust 10

Ultraviolet (UV) Lamp 10

Safety Precautions 11-12

CHAPTER 5: USING THE CABINET 13

Fan/UV Light Switch 13

UV Security Lock 13

Filter System Light 13

Shelf Operation 14

Drying in the Cabinet 15-16

CHAPTER 6: MAINTAINING THE CABINET 17

Routine Maintenance Schedule 17

Service Operations 18

Door Evidence Prefilter Replacement 18

Door Prefilter Replacement 18

Cabinet Evidence Prefilter Replacement 19

Cabinet Prefilter Replacement 19

Granular Activated Carbon and HEPA Filter Replacement 20

Changing the UV Lamp 21

Resetting a Circuit Breaker 22

Setting the Speed Control 22

CHAPTER 7: TROUBLESHOOTING 23-24

APPENDIX A: COMPONENTS 25

APPENDIX B: DIMENSIONS 26

APPENDIX C: SPECIFICATIONS 27

APPENDIX D: ACCESSORIES 28-29

Product Service 1-800-522-7658

Congratulations on the purchase of a Labconco Protector Evidence Drying

Cabinet. The cabinet is designed to protect you, and the room environment

from biohazardous aerosols and offensive odors while drying evidence. The

Protector Series cabinet is the result of years of experience in manufacturing

laboratory equipment, and users like you suggested many of its features to us.

The Evidence Drying cabinet models offer many unique features to enhance

performance and flexibility. To take full advantage of them, please acquaint

yourself with this manual and keep it handy for future reference. If you are

unfamiliar with how evidence drying cabinets operate, please review Chapter

4: Performance Features and Safety Precautions before you begin using the

cabinet. Even if you are an experienced cabinet user, please review Chapter

5: Using the Cabinet; it describes the cabinet’s features so that you can use it

efficiently.

This manual and other technical information is available in PDF format

at our website: www.labconco.com.

Product Service 1-800-522-7658

Before you install the evidence drying cabinet, you need to plan the site for

installation. Examine the location where you intend to install the cabinet.

You must be certain that the area is level and of solid construction. In

addition, a source of electrical power must be located near the installation

site.

Carefully read this chapter to learn:

Location requirements.

Electrical power requirements.

Exhaust requirements.

Service utility requirements.

Space requirements.

Refer to Appendix C: Specifications, for complete cabinet electrical and

environmental conditions, specifications and requirements.

Space Requirements

The dimensions for the evidence drying cabinet are shown in Appendix B:

Dimensions.

Clearance

A minimum clearance of at least 6 inches (150 mm) is suggested on the top

of the cabinet for service. There should be 36 inches (914 mm) clearance at

the front of the cabinet to allow the door to swing open without hitting any

obstructions.

Chapter 2: Prerequisites

Product Service 1-800-522-7658

Location Requirements

Note: The cabinet is equipped with leg levelers to ease level cabinet

installation. It should be located on a flat surface for proper cabinet

alignment and door operation.

Exhaust Requirements

If you intend to connect the cabinet to the optional Exhaust Connection Kit,

first examine the location to ensure that it accommodates the cabinet’s

exhaust duct. The area directly above the cabinet’s exhaust port should be

clear of structural elements, water and utility lines, or other fixed

obstructions. There should be enough clearance to accommodate a 5-inch

diameter duct. For further information about the cabinet’s exhaust system

requirements, please refer to Appendix D: Accessories.

Electrical Requirements

The evidence drying cabinet models have the following electrical

requirements:

Model #

Requirements

33900-00

115 VAC, 60 Hz, 6 Amps

33900-01

230 VAC, 50/60 Hz, 3 Amps

Note: An outlet with a circuit breaker rated at 10 amps for 115 volt

models (5 amps for 230 volt models) should be located as close as possible

to the right rear side of the cabinet. Power cords supplied with the

Evidence Drying cabinet are 3 meters (10 feet) long.

Table 2-1

Product Service 1-800-522-7658

Now that the installation site is properly planned, you are ready to inspect

and install the Protector evidence drying cabinet. This chapter covers how to:

Unpack and move the cabinet.

Install the cabinet.

Connect the electrical supply source.

Tools required for installation the cabinet include two 1/2" wrenches, a flat-

blade screwdriver, a #2 Phillips screwdriver, , scissors, or a box knife.

Note: The cabinet weighs approximately 250 lbs. (114 kg). The shipping

pallet allows for lifting with a mechanical lift truck or floor jack. If you must

lift the product manually, use at least three (3) persons and follow safe-lifting

guidelines.

Unpacking the Cabinet

Carefully remove the outer carton and inspect the cabinet for damage that

may have occurred in transit. If the cabinet is damaged, notify the delivery

carrier immediately and retain the entire shipment intact for inspection by the

carrier.

Note: United States Interstate Commerce Commission rules require that

claims be filed with the delivery carrier within fifteen (15) days of delivery.

Do not return goods without the prior authorization of Labconco.

Unauthorized returns will not be accepted.

If the cabinet was damaged in transit, you must file a claim directly with the

freight carrier. Labconco Corporation and its dealers are not responsible for

shipping damages.

Chapter 3: Getting Started

Product Service 1-800-522-7658

Do not discard the carton or packing material for the cabinet until all of the

components have been checked, installed and tested.

The cabinet is secured to the pallet using four (4) bolts. To remove the

cabinet, remove four (4) bolts from underneath top skid boards that are

holding the cabinet to the skid. You do not need to save these bolts and

washers. In the clear plastic bag inside the cabinet, are four (4) leg levelers.

Screw these into the holes the bolts came out of before removing the cabinet

from the pallet.

The cabinet is now ready to be removed from the pallet.

After removing the cabinet from the pallet, carefully remove plastic wrapping

around the cabinet, and open the cabinet door. Locate the two transport

brackets attached to the face of the cabinet liner. Using a #2 Phillips

screwdriver, remove the screws securing the brackets, discard the brackets,

and reinstall the screws.

Preparing the Evidence Drying Cabinet for

Operation

After the evidence drying cabinet has been removed from its pallet and

positioned in its final location, you must:

1. Remove the tie and/or tape securing the door, and the filters on top of

the unit.

2. Ensure that the transport brackets have been removed from the front

of the cabinet liner.

Note: The following are located in a box in the cabinet:

User’s Manual

UV Security Lock Key(s) (model #s 34000-00, -04 only)

Power Cord

Product Registration Card

If you did not receive one or more of the components listed for the

cabinet, or if any of the components are damaged, contact Labconco

Corporation immediately for further instructions.

3. Using a step ladder, remove the tape and/or packaging material

around the top of the unit.

4. Plug the power cord into the back of the cabinet, and then into an

appropriate outlet. Install the Key into the UV Security lock on the

upper panel on those models equipped with a UV light.

Chapter 3: Getting Started

Product Service 1-800-522-7658

Initial Operation

Prior to use with evidence, you should perform the following operational

tests to ensure the cabinet is operating properly:

Airflow Smoke Pattern Test

With the cabinet fan ON, introduce smoke (from a cigarette,

chemical smoke stick, etc.) into the prefilter at the bottom of

the door. The smoke should flow directly into the cabinet, and

then into the upper prefilter located at the top of the cabinet

liner. The smoke should move from the door to the intake

prefilter in approximately 5 seconds or less. If the smoke does

not flow as described, see the “Adjusting the Fan Speed”

section of Chapter 6.

UV Light and Interlock Tests

With the door closed, turn the “Fan/UV Light” switch to “UV”

and the “UV Security Keylock to “ON”. The UV light will

then turn on. Open the door, and the UV light will turn off.

Close the door, and the UV light should relight. Turn the UV

Security Keylock to the “OFF” position, and the UV light will

turn off. If the UV light does not work as described, call

Labconco’s Product Service Department at 1-800-522-7658 or

816-333-8811.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Labconco Laborausrüstung Handbücher

Labconco

Labconco CentriVap-105 Cold Trap Bedienungsanleitung

Labconco

Labconco FreeZone 70020 Series Bedienungsanleitung

Labconco

Labconco FreeZone 7750000 Bedienungsanleitung

Labconco

Labconco Protector XL 1124 Series Bedienungsanleitung

Labconco

Labconco FreeZone Plus Bedienungsanleitung

Labconco

Labconco Purifier Class 2 Biological Safety Cabinet Bedienungsanleitung

Labconco

Labconco Purifier 3951400 Bedienungsanleitung

Labconco

Labconco FreeZone 6 Bedienungsanleitung

Labconco

Labconco 5530000 Bedienungsanleitung

Labconco

Labconco 44003 Series Bedienungsanleitung

Labconco

Labconco FreeZone 70061 6L -50C Series Bedienungsanleitung

Labconco

Labconco CentriVap 7812010 Bedienungsanleitung

Labconco

Labconco Protector Premier 10040 Series Bedienungsanleitung

Labconco

Labconco Fiberglass 30 Series Bedienungsanleitung

Labconco

Labconco FreeZone Triad 74000 Series Bedienungsanleitung

Labconco

Labconco CentriVap DNA Systems Bedienungsanleitung

Labconco

Labconco 5530000 Bedienungsanleitung

Labconco

Labconco CentriVap 78110-00 Bedienungsanleitung

Labconco

Labconco Purifier Logic+ 30231 Bedienungsanleitung

Labconco

Labconco Protector 3410000 Bedienungsanleitung

Labconco

Labconco RapidVap 73200 Series Bedienungsanleitung

Labconco

Labconco Capture BT 31700-00 Bedienungsanleitung

Labconco

Labconco CentriVap 78110 Series Bedienungsanleitung

Labconco

Labconco Protector XStream 9840400 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung