Labnet C1301 Bedienungsanleitung

Spectrafuge Mini Centrifuge

User Manual

C1301

C1301-230V

About This Manual

This manual is designed to assist you in the optimal usage of your Spectrafuge Mini

Centrifuge. The manual is available in English, French, German, Italian, Portuguese,

and Spanish on our website at www.labnetinternational.com

General Information:

The Spectrafuge Mini Centrifuge is supplied with two rotors, one for microtubes and one

for 0.2ml PCR strip tubes. The 6 x 1.5ml rotor is designed to centrifuge up to six

individual 1.5ml plastic microcentrifuge tubes. It will also accept 0.5ml and 0.4ml tubes

with the adapters supplied with the unit. Adapters are available separately for 0.2ml

tubes. The strip tube rotor is designed to centrifuge two 8 x 0.2ml strip tubes. It will also

accept up to 16 individual 0.2ml tubes. Both rotors are designed for applications

requiring relatively low g-forces, such as microfiltration, cell separation and quick spin

downs from the walls of tubes. Please read this manual thoroughly before attempting to

operate the centrifuge.

If the equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Warranty:

The centrifuge and rotor are covered by a one year warranty. This warranty covers the

centrifuge and rotor. This warranty is void in the event of incorrect operation, use of

nonstandard spare parts or accessories and unauthorized modification of the rotor or

centrifuge. The rotor warranty does not cover normal wear and tear or damage and/or

weakening caused by radioactive contamination, cleaning agents, or over tightening of

the allen screw. Fuses are not covered by the warranty.

Exchanging Rotors:

The centrifuge is supplied with two interchangeable rotors. The rotors are easily

exchanged using the allen wrench provided. Locate the set screw on the rotor shaft

below the rotor head. Using the wrench, loosen the set screw and pull up on the rotor to

remove. Place the other rotor into position on the motor shaft. Take care not to press the

rotor down so far as to compress the rubber collar at the base of the shaft. Tighten the

screw using the allen wrench until finger tight. Do not over tighten as this will cause

damage to the rotor and the motor shaft.

Installation:

Place the centrifuge on a level, clean surface, position the centrifuge near an accessible

power outlet so that the cord and outlet are within easy reach of the operator.

Operation:

Before operating the centrifuge, be sure that the power switch is in the “on” position. To

begin a run, simply close the lid of the centrifuge. No other controls are required. To stop

rotation, press down on the lid release tab on the front of the unit. This will release the lid

lock and the rotor will slow gradually to a complete stop. Caution: Do not attempt to open

the lid or remove samples until the unit has come to a complete stop. After the rotor has

stopped, the lid may be opened by grabbing it with the thumb on the front and fingers on

the back then lifting the lid back on the hinge. Safe operation of the centrifuge requires

that the rotor be loaded in a balanced fashion. Failure to load the rotor properly presents

a hazardous condition and may damage the centrifuge. Individual tubes, strip tubes

and/or adapters must always be loaded symmetrically to ensure proper balance. Never

run the centrifuge with only one strip tube in place.

Safety Precautions:

NEVER use the centrifuge in any manner not specified in these instructions.

NEVER put hands in the rotor area unless the rotor is completely stopped.

NEVER move the centrifuge while the rotor is spinning.

NEVER use solvents or flammables near this or other electrical equipment.

NEVER centrifuge flammable, explosive or corrosive materials

NEVER centrifuge hazardous materials outside of a hood or proper containment

facility

NEVER continue to operate a centrifuge that is vibrating excessively.

ALWAYS load the rotor symmetrically. Each plate should be counterbalanced by

another plate of the same brand, type and volume.

ALWAYS use plates that have been sealed in some manner to avoid spillage.

ALWAYS load plates so that the sealed side faces the center of the rotor and the

bottom of the plate faces out.

ALWAYS be sure the plates are pushed all the way to the bottom of the rotor slot

before operating the centrifuge.

ALWAYS locate the centrifuge within easy access to an electrical outlet.

Cleaning:

Before using any cleaning or decontamination methods except those recommended by

the manufacturer, check with the manufacturer that the proposed method will not

damage the equipment. To clean the centrifuge, use a damp cloth and a mild,

noncorrosive detergent (ph <8). After cleaning, ensure all parts are dried thoroughly

before attempting to operate the unit. Do not immerse the centrifuge in liquid or pour

liquids over it.

Questions and Service:

Should you have a question about the operation of the Spectrafuge Mini Centrifuge or if

service is required, contact Corning at: 800-492-1110. Do not send in a unit for service

without first calling to obtain a repair authorization number. Should the unit require

return to Corning for service, it should be properly packed to avoid damage. Any

damage resultingfrom improper packaging shall be the responsibility of the user.

Specifications:

Dimensions... ........ 6” x 6” (153 x 153mm)

Electrical ............... 115V, 50/60Hz,130mA

Fuse ..................... 0.5A, 250V (F)

Speed ................... 6000rpm

RCF ...................... 2000 x g Ambient Operating Range: 0 to 40°C,< 85%

Spare Parts:

Replacement 1.5ml rotor: C-1300-RT

Replacement strip rotor: C-1300-RTS

Replacement allen key: C-1300-RW

Replacement fuses: ME973

Appendix

Symbols and Conventions

The following chart is an illustrated glossary of the symbols that may be used in this

manual or on the product.

The electrical warning indicates the presence of a potential hazard which

could result in electrical shock.

CAUTION This symbol refers you to important operating and maintenance

(servicing) instructions within the product Instruction Manual. Failure to

heed this information may present a risk of damage or injury to persons or

equipment.

This symbol identifies a Protective Earth (PE) terminal, which is provided for

connection of the supply system’s protective earth (green or green/yellow)

conductor.

Equipment Disposal—European Regulations

According to Directive 2012/19/EU of the European Parliament and of the

Council of 4 July 2012 on waste electrical and electronic equipment (WEEE),

Spectrafuge Mini Centrifuge is marked with the crossed-out wheeled bin and

must notbe disposed of with domestic waste.

Consequently, the buyer shall follow the instructions for reuse and recycling of

waste electronic and electrical equipment (WEEE) provided with the products

and available at the following link: www.corning.com/weee

Warranty Statement

Corning Incorporated (Corning) warrants that this product will be free from defects in material and

workmanship for a period of one (1) year from date of purchase. CORNING DISCLAIMS ALL

OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.

Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof

that proves defective in material or workmanship within the warranty period, provided the

purchaser notifies Corning of any such defect. Corning is not liable for any incidental or

consequential damages, commercial loss or any other damages from the use of this product.

This warranty is valid only if the product is used for its intended purpose and within the guidelines

specified in the supplied instruction manual. This warranty does not cover damage caused by

accident, neglect, misuse, improper service, natural forces or other causes not arising from

defects in original material or workmanship. This warranty does not cover motor brushes, fuses,

light bulbs, batteries or damage to paint or finish. Claims for transit damage should be filed with

the transportation carrier.

In the event this product fails within the specified period of time because of a defect in material or

workmanship, contact Corning’s Customer Service at the following numbers: USA: 1-800-492-

1110; Canada: 1-978-442-2200. For other regions of the world, please visit

www.corning.com/lifesciences or see the included instruction manual for a list of World Wide

Support Offices.

Corning’s Customer Service team will help arrange local service where available or coordinate a

return authorization number and shipping instructions. Products received without proper

authorization will be returned. All items returned for service should be sent postage prepaid in

the original packaging or other suitable carton, padded to avoid damage. Corning will not be

responsible for damage incurred by improper packaging. Corning may elect for onsite service for

larger equipment.

Some states do not allow limitation on the length of implied warranties or the exclusion or

limitation of incidental or consequential damages. This warranty gives you specific legal

rights. You may have other rights which vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend

the period of this warranty.

For your reference, make a note of the serial number, date of purchase and supplier here.

Serial No. ____________________ Date Purchased _________________

Supplier _____________________________________________________

Warranty/Disclaimer: Unless otherwise specified, all products are for research use only. Not intended for use in diagnostic

or therapeutic procedures. Corning makes no claims regarding the performance of these products for clinical or diagnostic

applications.

Please register your product online at:

www.labnetinternational.com

NOTES

Labnetinfo@corning.com

www.labnetinternational.com

LN1010000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Labnet Laborausrüstung Handbücher

Labnet

Labnet FASTPETTE PRO Bedienungsanleitung

Labnet

Labnet Spectrafuge 6C Bedienungsanleitung

Labnet

Labnet BioPette Multichannel Bedienungsanleitung

Labnet

Labnet Accublock D1301 Bedienungsanleitung

Labnet

Labnet W1106A Bedienungsanleitung

Labnet

Labnet Rocker 35 EZ Bedienungsanleitung

Labnet

Labnet ProBlot Rocker 25 Bedienungsanleitung

Labnet

Labnet C0336 Bedienungsanleitung

Labnet

Labnet I-4001-HCS Bedienungsanleitung

Labnet

Labnet 25 Bedienungsanleitung

Labnet

Labnet Prism Bedienungsanleitung

Labnet

Labnet Spectrafuge 6C Bedienungsanleitung

Labnet

Labnet Prism Mini Bedienungsanleitung

Labnet

Labnet MultiGene OptiMax TC9610 Bedienungsanleitung

Labnet

Labnet BioPette PLUS BPP2 Bedienungsanleitung

Labnet

Labnet VorTemp 1550 Bedienungsanleitung

Labnet

Labnet C1601-B Bedienungsanleitung

Labnet

Labnet D0100 Bedienungsanleitung

Labnet

Labnet Excel P3600L-10 Bedienungsanleitung

Labnet

Labnet Spectrafuge 16M Bedienungsanleitung

Labnet

Labnet ProBlot 6 Bedienungsanleitung

Labnet

Labnet Spectrafuge 6C Bedienungsanleitung

Labnet

Labnet C1303-T Bedienungsanleitung

Labnet

Labnet ENDURO VE10 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung