Labnet D0100 Bedienungsanleitung

Instruction Manual

Mini Digital Dry Bath

Models D0100 and D0100-230V

Labnet International, Inc.

PO Box 841

Woodbridge, NJ 07095

Phone 732 417-0700

Fax 732 417-1750

email labnet@labnetlink.com

www.labnetlink.com

1.0 General Specifications

Temperature range Ambient +5° to 100°C

Temp. increments 0.1ºC

Temp. uniformity ≤0.2ºC

Temp. accuracy ≤0.2ºC

Timer 0 -19h:59m or continuous

Block Anodized Aluminum

Block capacity 12x 1.5mL tubes

Dimensions (WxDxH) 5.5 x 4.8 x 2.4 in./14 x 12 x 6 cm

Weight 3 lb/1.3 kg

Electrical 120V or 230V~, 50/60 Hz

Electrical requirements:

100-240V, 50/60Hz, 0.7A –30W Max

2.0 Safety Precautions:

- Do not use this product in an explosive environment

- Do not use in the presence of flammable or combustible material

- Do not heat substances that react violently when heated

- Do not touch area around block or block well when unit is hot.

- Do not spill liquids into the well area or into the unit

- Connect unit only to a properly grounded outlet

Caution: HOT Surfaces that can burn or cause injury.

Use of this product in any manner not specified by the manufacturer or modification of the product

may cause injury and/or may void the warranty.

3.0 Installation

Upon unpacking Mini Digital Dry Bath, inspect for damages. Shipping damage is the responsibility

of the carrier. Inspect that the following are present:

AccuBlock™Mini with AccuRack™

Users manual

Switching Power Adapter

Line cord

Select a location that is dry and not subject to drafts or moving air from heating or air conditioning

vents, or air blown by other equipment. Place the unit on a flat, preferably non-flammable surface.

Allow sufficient room around the unit for access and cooling. Six inches minimum on all sides is

suggested. Plug the unit into a properly grounded outlet. Using the lifter, insert the block(s) into

the well. The unit is now ready for use.

4.0 Controls

LCD Display (Block Temperature, Set Temperature, Timer)

Heat LED (Heater Function)

Main Power Switch Turns entire unit on and off.

START/STOP Switch Begins and ends the heating process

Mode Switch Toggles the LCD display between Temperature and Timer Settings

Up Switch Used to increment the set temperature.

Down Switch Used to decrement the set temperature.

5.0 Operation

1. Turn the unit on using the Main Power rocker switch on the rear of the unit.

2. The LCD will display a self test and the LED will turn on.

3. After two seconds the unit will enter normal operation and display the current temperature

of the block.

4. Press the Up or Down switches to set the block to the desired temperature. The display

will change to the current temperature set point. The temperature is set in 0.1 degree C

increments. Holding the Up or Down key for more the eight seconds will increase or

decrease the set point rapidly. The display will automatically return to current temperature

four seconds after the switch is released. Note, the temperature may not be adjusted with

the unit actively heating the block.

5. The temperature setting will be stored in memory when the display returns to the current

block temperature. This setting will be retained if the power is turned off. Note the display

must return to current temperature before the power is turned off or the new set

temperature will NOT be saved.

6. Press the START/STOP to begin the temperature control. The “^” will be displayed on the

LCD when the unit is in active temperature control.

7. The LED will turn on and off with the heating element.

8. The LED will be off when the unit is turned off and when the heater is not actively heating

the block.

9. The maximum set temperature is 101C.

10. The Mode switch will scroll through current temperature, the elapsed time from the press

of the START button, LCD off and countdown timer.

Heating & Countdown Timer

1. Turn the unit on using the Main Power rocker switch.

2. Press the Up or Down switches to set the block to the desired temperature. Holding the

Up or Down key for more the eight seconds will increase or decrease the set point

rapidly. The display will automatically return to current temperature four seconds after the

switch is released. Note, the temperature may not be adjusted with the unit running.

3. Press the Mode button until “1:00” is displayed. This is the default Count Down timer

setting. The maximum time is setting is 19:59.

4. Press the up or down key to set the desired count down time.

5. Press Start/Stop button to begin heating.

6. The LCD will alternate between actual temperature and time remaining.

7. When time runs out the LCD will alternate between the current temperature and “---“. The

beeper will sound when “---“ is displayed.

8. Heating will NOT turn off when time expires.

9. To cannel the countdown timer press the Mode key one time to advance to the standard

temperature only read out.

6.0 Calibration

1. Press and hold the Start/Stop then simultaneously powering up the unit with the

ON/OFF switch.

2. Release the Start/Stop button when the LCD displays “---“.

3. The will beep 4 times and the display will show the calibration set point and the “:” will

flash rapidly.

4. Press the UP or Down keys to set the desired temperature at which you want to

calibrate the unit.

5. Press the Start/Stop to begin calibration. The “^” will be displayed on the LCD when

the unit is in active temperature control.

6. Allow 10 –40 minutes for the unit to heat up and reach equilibrium. A high

temperature calibration set point will require more time.

8. After the unit has equalized the LCD will flash “---“and the current temperature.

9. Read the thermometer (or sensor meter) and use the UP and Down keys to adjust

the display to the thermometer or sensor reading.

10. Press the Start/Stop key to save the new settings.

11. Press the Start/Stop key again. The unit will adjust to the operating temperature with

the new calibration factor. Allow sufficient time for the unit to re-equilibrate and then

compare the thermometer or sensor reading to the calibrated display. They should

closely match (2+/- 0.2 C). If not, repeat calibration procedure.

7.0 Troubleshooting Guide / Service (Labnet Service 1-888-LABNET-1)

Problem Explanation / Solution

Display / LEDs do not light up

1. Check power cord & outlet.

2. Check ON / OFF switch.

3. Check for Light on Power Adapter.

4. Call service.

Unit not heating

1. Is set point below room temp?

2. Is Heating LED turning Off and On?

3. Press “Start/Stop” key.

4. Is the “^”displayed on the LCD?

5. Call service.

Block or Sample temp not same as display temp.

1. Is unit in heating mode?

2. Is unit sitting in draft?

3. Check accuracy of thermometer.

4. Is reference thermometer making good contact?

5. Follow calibration procedure

8.0 Cleaning and Maintenance

Make sure that the dry bath and block are cool and the power cord is disconnected before

performing any cleaning or maintenance. Repair or maintenance should only be performed by an

authorized service technician.

The dry bath may be cleaned with a moist cloth containing a mild soap solution. Do not immerse

the dry bath in water or any liquid.

Spills: In the event liquid is accidentally spilled into the block area, disconnect the plug from the

outlet and turn the unit upside down to minimize liquid contact with the internal components.

Allow the unit to dry. Have qualified service technician clean the unit and replace any damaged

parts.

P.O. Box 841 • Woodbridge, NJ 07095 • USA • website: http://www.labnetlink.com

US • toll free: 888-LABNET1 • fax: 732 417-1750 • email: labnet@labnetlink.com

International • phone: +1-732-417-0700 • fax: +1-732-417-1750 •

email: international@labnetlink.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Labnet Laborausrüstung Handbücher

Labnet

Labnet Z100-A Bedienungsanleitung

Labnet

Labnet MPS 1001 Mini Plate Spinner Bedienungsanleitung

Labnet

Labnet Prism Mini Bedienungsanleitung

Labnet

Labnet Excel E10-1 Bedienungsanleitung

Labnet

Labnet H5500 Bedienungsanleitung

Labnet

Labnet 222DS Bedienungsanleitung

Labnet

Labnet BioPette PLUS Bedienungsanleitung

Labnet

Labnet ESCZ100A Bedienungsanleitung

Labnet

Labnet 311DS Bedienungsanleitung

Labnet

Labnet AccuPlate D0300 Bedienungsanleitung

Labnet

Labnet FastPette Pro Bedienungsanleitung

Labnet

Labnet VorTemp 1550 Bedienungsanleitung

Labnet

Labnet C1301 Bedienungsanleitung

Labnet

Labnet Rocker 35 EZ Bedienungsanleitung

Labnet

Labnet FASTPETTE Bedienungsanleitung

Labnet

Labnet BioPette PLUS BPP2 Bedienungsanleitung

Labnet

Labnet C1303-T Bedienungsanleitung

Labnet

Labnet BioPette PLUS Bedienungsanleitung

Labnet

Labnet Spectrafuge 16M Bedienungsanleitung

Labnet

Labnet S0200 Bedienungsanleitung

Labnet

Labnet AccuPlate D0410 Bedienungsanleitung

Labnet

Labnet Spectrafuge 16M Bedienungsanleitung

Labnet

Labnet I-4001-HCS Bedienungsanleitung

Labnet

Labnet Prism R Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung