Labnet C1303-T Bedienungsanleitung

Lit M00406 Rev. September 2016

Slide Spinner

User Manual

C1303-T

C1303-T-230V

General Information:

The Labnet Slide Spinner is a personal centrifuge supplied with a rotor and cassettes to

hold 2 microarray or standard microscope slides. The Slide Spinner is designed for

drying liquid from glass slides, typically microarray slides. Please read this manual

thoroughly before attempting to operate the centrifuge.

Operation:

Insert a slide into each of the cassettes on the rotor. Note: Always run 2 slides at once.

Use a blank slide as a balance if only one slide needs to be tried. To begin a run, simply

close the lid of the centrifuge. No other controls are required. To stop rotation, press

down on the lid release tab on the front of the unit or put the switch on the side to the “off”

position. Pressing the tab will release the lid lock and the rotor will slow gradually to a

complete stop.

Caution: Do not attempt to open the lid or remove samples until the unit has come to a

complete stop. After the rotor has stopped, the lid may be opened by grabbing it with

the thumb on the front and fingers on the back then lifting the lid back on the hinge.

Safe operation of the centrifuge requires that the rotor be loaded in a balanced fashion.

Failure to load the rotor properly presents a hazardous condition and may damage the

centrifuge. Always run two slidesfor proper rotor balance. Typically a 10 second spin is

required to completely dry the microarray slides. After a 10 second spin, switch the unit

off via the power switch. When the rotor has come to a complete stop, open the lid and

remove the slides. The cassettes can be removed from the rotor for easy disposal of the

liquid that collects at the bottom of the cassettes.

Safety Precautions:

NEVER use the centrifuge in any manner not specified in these instructions.

NEVER operate the centrifuge without a rotor properly attached to the shaft.

NEVER put hands in the rotor area unless the rotor is completely stopped.

NEVER use solvents or flammables near this or other electrical equipment.

NEVER move the centrifuge while the rotor is spinning.

NEVER use solvents or flammables near this or other electrical equipment.

NEVER centrifuge flammable, explosive or corrosive materials.

NEVER centrifuge hazardous materials outside of a hood or proper containment

facility

NEVER spin slides that do not fit easily into the cassettes.

NEVER Autoclave. Autoclaving can cause the polycarbonate to lose its strength over

time.

ALWAYS load the rotor symmetrically. Each slide should be counterbalanced by the

second slide.

ALWAYS locate the centrifuge within easy access to an electrical outlet.

Cleaning:

Before using any cleaning or decontamination methods except those recommended by

Labnet, check with Labnet that the proposed method will not damage the equipment. To

clean the centrifuge, use a damp cloth and a mild, noncorrosive detergent (ph<8). After

cleaning, ensure all parts are dried thoroughly before attempting to operate the unit. Do

not immerse the centrifuge in liquid or pour liquids over it.

The recommended cleaning method for the cassettes is a mild non-akaline detergent.

For decontamination of internal part of the cassettes, Labnet recommends using

Ultrasonic Cleaning Units (it is very effective for destroying DNA-autoclaving doesn’t

effectively destroy DNA)

The cassettes are not resistant to alkaline detergents, or acids.

Questions and Service:

Should you have a question about the operation of the Slide Spinner or if service is

required, contact Corning at: 800-492-1110. Do not send in a unit for service without

first calling to obtain a repair authorization number. Should the unit require return to

Corning for service, it should be properly packed to avoid damage. Any damage

resulting from improper packaging shall be the responsibility of the user.

Specifications:

Dimensions ............5.9 x 5.9 x 4.6 in/15 x 15 x 11.7 cm

Electrical ............... 100,120 or 230V, 50/60 Hz

Max Speed ............ 4,000rpm (±10%)

Max RCF ............... 500-850 x g

Spare Parts:

Replacement fuses: C1200-F

Replacement cassettes: C1303-RC

EQUIPMENT DISPOSAL-EUROPEAN REGULATIONS

According to Directive 2012/19/EU of the European

Parliament and of the Council of 4 July 2012 on waste

electrical and electronic equipment (WEEE), Labnet Slide

Spinner is marked with the crossed-out wheeled bin and

must not be disposed of with domestic waste.

Consequently, the buyer shall follow the instructions for reuse

and recycling of waste electronic and electrical equipment

(WEEE) provided with the products and available at the

following link: www.corning.com/weee

By doing so, you will help to conserve natural and environmental resources and you will

ensure that your equipment is recycled in a manner that protects human health.

Warranty Statement

Corning Incorporated (Corning) warrants that this product will be free from defects in material and

workmanship for a period of one (1) year from date of purchase. CORNING DISCLAIMS ALL

OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.

Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof

that proves defective in material or workmanship within the warranty period, provided the

purchaser notifies Corning of any such defect. Corning is not liable for any incidental or

consequential damages, commercial loss or any other damages from the use of this product.

This warranty is valid only if the product is used for its intended purpose and within the guidelines

specified in the supplied instruction manual. This warranty does not cover damage caused by

accident, neglect, misuse, improper service, natural forces or other causes not arising from

defects in original material or workmanship. This warranty does not cover motor brushes, fuses,

light bulbs, batteries or damage to paint or finish. Claims for transit damage should be filed with

the transportation carrier.

In the event this product fails within the specified period of time because of a defect in material or

workmanship, contact Corning’s Customer Service at the following numbers: USA: 1-800-492-

1110; Canada: 1-978-442-2200. For other regions of the world, please visit

www.corning.com/lifesciences or see the included instruction manual for a list of World Wide

Support Offices.

Corning’s Customer Service team will help arrange local service where available or coordinate a

return authorization number and shipping instructions. Products received without proper

authorization will be returned. All items returned for service should be sent postage prepaid in

the original packaging or other suitable carton, padded to avoid damage. Corning will not be

responsible for damage incurred by improper packaging. Corning may elect for onsite service for

larger equipment.

Some states do not allow limitation on the length of implied warranties or the exclusion or

limitation of incidental or consequential damages. This warranty gives you specific legal

rights. You may have other rights which vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend

the period of this warranty.

For your reference, make a note of the serial number, date of purchase and supplier here.

Serial No. ____________________ Date Purchased _________________

Supplier _____________________________________________________

Warranty/Disclaimer: Unless otherwise specified, all products are for research use only. Not intended for use in diagnostic

or therapeutic procedures. Corning makes no claims regarding the performance of these products for clinical or diagnostic

applications. Please register your product online at:

www.labnetinternational.com

labnetinfo@corning.com

www.labnetinternational.com

LN102000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Labnet Laborausrüstung Handbücher

Labnet

Labnet Labpette R Bedienungsanleitung

Labnet

Labnet Z100-A Bedienungsanleitung

Labnet

Labnet Rocker 35 EZ Bedienungsanleitung

Labnet

Labnet ProBlot Rocker 25 Bedienungsanleitung

Labnet

Labnet Prism Mini Bedienungsanleitung

Labnet

Labnet AccuPlate D0400 Bedienungsanleitung

Labnet

Labnet C0336 Bedienungsanleitung

Labnet

Labnet Excel P3600L-10 Bedienungsanleitung

Labnet

Labnet Spectrafuge C1301 Bedienungsanleitung

Labnet

Labnet Spectrafuge 6C Bedienungsanleitung

Labnet

Labnet ENDURO GEL XL E0160 Bedienungsanleitung

Labnet

Labnet BioPette Multichannel Bedienungsanleitung

Labnet

Labnet Excel E10-1 Bedienungsanleitung

Labnet

Labnet FASTPETTE Bedienungsanleitung

Labnet

Labnet Orbit S2030-LS-B-230 Bedienungsanleitung

Labnet

Labnet 222DS Bedienungsanleitung

Labnet

Labnet BioPette E BE20-1 series Bedienungsanleitung

Labnet

Labnet MPS 1001 Mini Plate Spinner Bedienungsanleitung

Labnet

Labnet TC9600-G Bedienungsanleitung

Labnet

Labnet VorTemp 1550 Bedienungsanleitung

Labnet

Labnet ENDURO VE10 Bedienungsanleitung

Labnet

Labnet FastPette Pro Bedienungsanleitung

Labnet

Labnet D0100 Bedienungsanleitung

Labnet

Labnet S0200 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung