Larson Electronics EPL-48-2L-T12VHO Bedienungsanleitung
EPL-48-2L-T12VHO
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1of 3
Surface Mount Explosion Proof, Waterproof Fluorescent Lights
T12 Very High Output - Oil Rigs - 2 L
Instruction Manual
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE EPL-48-2L-T12VHO MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE
AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
Thank you for your purchase of the Larson Electronics EPL-48-2L-T12VHO.
)
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The Larson Electronics EPL-48-2L-T12VHO Explosion Proof Fluorescent Light Fixture is NRTL Listed for United States
and Canada Class 1 Division 1 and Class 1 Division 2 for hazardous locations where flammable chemical/petrochemical
vapors exist or have the potential to exist. The unit carries a T6 temperature rating, it is also approved for Paint Spray
Booths.
EPL-48-2L-T12VHO
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2of 3
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 120V OR 277V AC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
ADJUSTABLE SURFACE MOUNTING BRACKETS
Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening
two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single
bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a
surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the
bracket to the mounting peg.
SUSPENSION MOUNTING
Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2” NPT junction box
on one end, and a 1/2” NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the
threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires,
completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the
fixture.
INSTALLATION
We strongly recommend that only a licensed electrician install this product.
Warning: Make sure that the power is disconnected before installing. This fixture is extremely heavy and must be
mounted to a surface that can structurally support the load. Note: this fixture requires a minimum of 50 inches of
clearance from re-lamp end for lamp replacement. An optional drop mounting kit that will allow for end to end row
mounting is available, please consult factory.
Warning: Do not let fixture hang on one bracket at any time. Failing to comply can result in breakage of and end
casting or mounting bracket allowing the fixture to fall which can cause serious injury or death.
•The mounting brackets are shipped installed on the fixture.
•Install the brackets to wall or ceiling with two 3/8’’ bolts (not supplied) at center measurements.
•Fixture is now ready for mounting.
It is strongly suggested to use two licensed electricians to proceed with the final mounting of the fixture to
avoid any possible personnel injury or damage to the fixture as the unit weights up to 66lbs (30.0 kg) and will
be slightly awkward to hold in position and attach to brackets mounted on wall or ceiling. Depending on
mounting height and scaffolding, a hydraulic man–lift or two good quality ladders should be used.
•Remove the upper center screw cap on the re-lamp end (field wiring compartment).
•Install approved cable connector or conduit fitting into ½’’ npt hub on field wiring compartment.
•Install a three conductor cable into the connector, allowing 3 inches of wire inside compartment for connection.
•Using approved wire connectors, splice wires as per color codes: black to black (line) white to white (common) and green to green
(ground).
•Replace end-cap, making sure there are no wires protruding that maybe pinched causing a possible short circuit.
Warning: Fixture must be grounded as required per paragraph 410-21 and article 250 of
the National Electric Code and/or rule 30-500. Failure to properly ground this fixture will
create and electrical shock, which can cause serious injury or death.
WIRING INSTRUCTIONS
EPL-48-2L-T12VHO
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 3of 3
MAINTENANCE
Caution:To avoid personal injury,disconnect powerto the light and allow theunit to cool down before performing maintenance.
Warning: No user serviceable parts inside of fixture.Risk of electricshock.Removalof the lenswill void the warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine checks to be made on a
yearly basis. Frequency of use and environment shoulddetermine this. It is recommendedto follow an Electrical Preventive
Maintenance Program as described in NFPA 70B: Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance. Clean the lens with a
damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e.excessive
dust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPL-48-2L-T12VHO is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Inhaltsverzeichnis
Andere Larson Electronics Beleuchtungsausrüstung Handbücher
Larson Electronics
Larson Electronics SL-ALM Bedienungsanleitung
Larson Electronics
Larson Electronics SPLED-QP-1X10WRE Bedienungsanleitung
Larson Electronics
Larson Electronics MMLP-150LED-RT-12P Bedienungsanleitung
Larson Electronics
Larson Electronics EPP-3P4W-30A-N7 Bedienungsanleitung
Larson Electronics
Larson Electronics EPLC2-QP-1X150LED-100 Bedienungsanleitung
Larson Electronics
Larson Electronics GAU-ID-36-1L-UVC-SPF Bedienungsanleitung
Larson Electronics
Larson Electronics EPLC2-PT-2X150LED-RT Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-HB-150LED-RT-DLC Bedienungsanleitung
Larson Electronics
Larson Electronics PML-15 Bedienungsanleitung
Larson Electronics
Larson Electronics LEDB-4-IR Bedienungsanleitung
Larson Electronics
Larson Electronics LEDLB-4-IR Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-LQP-2X150RT Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-PM-150LED Handbuch
Larson Electronics
Larson Electronics WAL-ML-2XM-3G Bedienungsanleitung
Larson Electronics
Larson Electronics LEDWP-600E-M-E2E Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-120-150-EPP Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-48-4L-LED-D-V2-100C Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-SL-2-LED-ITG-M2 Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-SL-4-50X-50LED-RT-MBC-EPP Bedienungsanleitung
Larson Electronics
Larson Electronics LEDSB-3XQF12V-1227-WF-3XKT Installationsanleitung
Larson Electronics
Larson Electronics HALD-48-1X100LED Bedienungsanleitung
Larson Electronics
Larson Electronics HID-35-RC-W Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-LED-150W-RT-140DB-480V Bedienungsanleitung
Larson Electronics
Larson Electronics GAU-HB-100LED-RT-UVA-10C Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
