Lava Parallel-PCI/LP Card Bedienungsanleitung

Lava Parallel-PCI/LP

Installation Manual

Rev. B00

LAVA

COMPUTERS

PARALLEL PCI/LP P.N. MOKO L72.4

MADE

CANADA

PN MOKO S-1

MADE IN JAPAN

0255351

Windows Hardware and

Driver Installation

1. Before opening the casing of your computer, make sure that all

power is off.

2. Locate an unused PCI slot and insert the Parallel-PCI/LP card into it.

Ensure that the card is well seated.

3. Screw the metal bracket of the Parallel-PCI/LP card to your PC’s

casing and replace the machine’s cover.

4. Connect your parallel (printer) cable to the port on the Parallel-

PCI/LP card and turn the PC on.

5. When Windows starts, it will find a Parallel-PCI/LP Controller and will

ask you for a driver for this device.When prompted, insert the

installation diskette into your floppy drive. After copying the

PCI Slot

Screw for attaching card bracket

to PC casing

Port

necessary files from the diskette,Windows may restart your PC in

order to complete the installation of the Parallel-PCI/LP card. Any

Plug and Play printers attached to the Parallel-PCI/LP will now also

be detected and installed.Windows XP may display a message to

the effect that the drivers are not digitally signed.This warning can

be ignored.

6. The Parallel-PCI/LP card will appear in Control Panel|System|Device

Manager under Ports, as a listing similar to the one below. If

required, settings may be customized by clicking on the Parallel-

PCI/LP listing and then clicking Properties. Please note that changes

to default settings may be required by users connecting the Parallel-

PCI/LP card to a non-printer peripheral (see reverse). Users

connecting a printer should use default settings.

Connecting a non-printer device

(e.g. external drive or parallel scanner)

to the Parallel-PCI/LP

In Windows 95/98/ME (not Windows 2000/XP) some parallel port

devices require parallel ports that use standard (legacy) ISA LPT

addresses (0278h or 0378h). Because the Parallel-PCI/LP card is a fully

compliant PCI device, its default address (Input/Output Range) is

beyond the standard range of ISA I/O addresses. In order to connect

such a peripheral to the Parallel-PCI/LP card, the I/O address range of the

card must therefore be changed manually.This section describes how

this is done.

1. Open Control Panel|System|Device Manager and find the Parallel-

PCI listing under Ports. Click Properties, and proceed to the

Resources tab.The following screen will appear (Note: the

Input/Output Range and Interrupt of your particular configuration

may differ from the one below).

2. Remove the check mark from the Use Automatic Settings box.

Note: In some cases Windows will give an error message to the effect

that "Windows cannot modify this resource" at this point. If you are

unable to access the settings for changing system resources, reboot the

system in Safe Mode to make changes to resource settings. (To enter

Safe Mode, press the F8 key while the system is rebooting.)

3. Double-click on the words Input/Output Range.The following

screen will appear:

4. Use the up/down arrows to scroll to one of the following range

settings, or type them in manually:

0278 – 027F 0378 – 037F

0238 – 023F 02B8 – 02BF

5. After one of these has been entered, click OK.Windows will verify

whether you would like to force this particular configuration rather

than the automatic one that it had previously chosen. Click Yes.

6. Verify that there are no conflicts with addresses being used by other

devices already in your PC. If no conflicts are found, restart Windows.

0338 – 033F

Using Zip Drives with the Parallel-PCI/LP

NOTE:The default input/output range for the Parallel-PCI/LP card works

with Zip Drives using new Iomegaware software.The instructions

"Connecting a non-printer device" given above apply to Zip Drive users

using old versions of Iomegaware.

For best results with Windows 2000 and XP, we recommend

downloading the latest "Iomegaware" from Iomega.

Additional instructions on optimizing Zip Drive performance with the

Parallel-PCI/LP can be found at www.lavalink.com.

Release Notes:

A. This documentation describes the installation of the Parallel-PCI/LP

card on a Windows95/98/Me/2000/XP PC. Instructions and software

for DOS,Windows 3.x, and Windows NT 4.0 may be found in the

NT4.0 subdirectory of the Parallel-PCI/LP card Installation diskette.

Instructions for Linux installation are available at www.lavalink.com.

B. Because the Parallel-PCI/LP card uses PCI (not ISA) I/O address

ranges, it will never be seen by your BIOS at boot-up as a standard

parallel port (occupying 0278h or 0378h) even if the address has

been changed in Windows using the above procedure.This is

normal, and does not indicate a fault in your Parallel-PCI/LP card.

C. The Parallel-PCI/LP card will not work at address 0278h or 0378h if it

is installed in a PCI slot that is behind a PCI-to-PCI bridge. If you have

trouble installing the Parallel-PCI/LP card, try seating it in a different

slot.

D. In standard installations of Windows 2000/XP, the I/O address cannot

be changed to a legacy address.

E. Some devices (like external CD writers) default to "word mode" (ie:

16-bit data transfer) for fastest performance. Such devices need to

operate in "byte mode" (8-bit data transfer) to work with the

Parallel-PCI/LP. Look in your device software for a "byte mode"

setting, and enable it.

Lava Computer MFG Inc.

Lava

Technical Support

9:00 am to 5:30 pm Monday to Friday (Eastern Time)

Tel: +416 674-5942

Fax: + 416 674-8262

E-mail: tech@lavalink.com

Internet: www.lavalink.com

This device complies with part 15 of the FCC Rules. Operation is subject

to the following conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Lava Computer MFG Inc. 908 Niagara Falls Blvd. #629. North Tonawanda NY 14120-2060

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lava PCI-Karte Handbücher

Lava

Lava Lava SSerial-550 Bedienungsanleitung

Lava

Lava QUATTRO-PCI 3.3V Bedienungsanleitung

Lava

Lava PCI Bus Enhanced Parallel Board Bedienungsanleitung

Lava

Lava Parallel-PCIe Bedienungsanleitung

Lava

Lava Lava 2SP-PCI Bedienungsanleitung

Lava

Lava LAVA Dual Parallel-PCI Bedienungsanleitung

Lava

Lava DSerial-PCI Powered Bedienungsanleitung

Lava

Lava LAVA SSerial-PCI/LP Bedienungsanleitung

Lava

Lava Enhanced Parallel Port Board Bedienungsanleitung

Lava

Lava FireHost Bedienungsanleitung

Lava

Lava LavaPort 650 Bedienungsanleitung

Lava

Lava SP-PCI Bedienungsanleitung

Lava

Lava Octopus-550 Bedienungsanleitung

Lava

Lava Lava Port 650 Bedienungsanleitung

Lava

Lava LAVA SP-PCI Bedienungsanleitung

Lava

Lava Dual Parallel-PCI Bedienungsanleitung

Lava

Lava LavaPort-Quad Bedienungsanleitung

Lava

Lava Parallel-PCI DB-25 Bedienungsanleitung

Lava

Lava SSerial-PCI/LP Bedienungsanleitung

Lava

Lava QUATTRO-PCI Bedienungsanleitung

Lava

Lava Quattro-PCI/LP Bedienungsanleitung

Lava

Lava 2SP-PCI Bedienungsanleitung

Lava

Lava Parallel-PCIe/LP Bedienungsanleitung

Lava

Lava Lava Parallel LAVA SP-PCIe Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung