LUCCI FUTURA ECO SERIES Bedienungsanleitung

FUTURA ECO SERIES

E27 LAMP HOLDER

CEILING FANS

IMPORTANT SAFETY INSTRUCTIONS

1) This appliance is NOT intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

2) The all-poles disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

3) Meaning of crossed-out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal

waste, use separate collection facilities. Contact your local government for information regarding the

collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into the food chain, damaging your health and

well-being.

4) The structure to which the fan is to be mounted must be capable of supporting a weight of 45kg.

5) The fan should be mounted so that the blades are at least 2.3 meters above the floor.

6) The fan is designed for indoor use only. Mounting the fan in a situation where it is subject to water or

moisture is dangerous.

7) Only an authorized electrician should execute the installation.

INTRODUCTION

CONGRATULATIONS, as you have just chosen a quality ceiling fan.

BEFORE INSTALLATION

Unpack the fan and carefully identify the parts. Please refer to FIGURE 1.

1. Hanger Bracket x 1

2. Pre-assembled Fan motor, down

rod, and canopy cover x 1

3. Glass shade x 1

4. Blades x 4

5. Screw for Hanger bracket x 2

6. Extra Motor screws for blade x 1

7. Wall plugs for Screw x 2

8. Balancing kits x 1 set

9. Receiver x 1

10. Transmitter x 1

Figure 1.

Specifications:

Model Rated Voltage Remote Fan

(watt) Lamp

xxxxxx 220-240V, 50HZ 1.5V, AAA X 4

60W MAX. 2 X 42W Halogen or

MAX. 2 x 15W CFL Spiral

xxxxxx 220-240V, 50HZ 1.5V, AAA X 4

60W MAX. 2 X 42W Halogen or

MAX. 2 x 15W CFL Spiral

xxxxxx 220-240V, 50HZ 1.5V, AAA X 4

60W MAX. 2 X 42W Halogen or

MAX. 2 x 15W CFL Spiral

INSTALLATION

NOTE: Ensure that the power to the supply wires has been turned off before attempting installation.

INSTALL THE MOUNTING BRACKET

Drill two mounting holes in the ceiling joist and securely screw

the mounting bracket to the ceiling using the washers and

mounting screws provided. The mounting plate should be able

to hold a weight of at least 45kg.

NOTE: Proper care must be taken when mounting to concrete

ceilings. For safe mounting, these ceilings may require

stronger screws and plastic plug or anchors than supplied with

the product.

Install mounting bracket (Fig. 2) to ceiling joist via using long

screws provided. Ensure that at least 40mm of the screw is

threaded into the support.

INSTALL THE FAN TO MOUNTING BRACKET ON CEILING

1. Carefully lift the fan and seat the down rod ball assembly into the spacing allocated in the mounting

bracket and lock the ball into place. Fig. 3

Fig.3

2. Remove the screws from the light plate and remove the light plate. Fig.4

Fig.4

3. Before installing the blades, remove the blades screws that was locked to motor in advance. Fig.5

Fig.5

4. Insert the blades through the side slot of motor and align with the 3 holes. If the holes do not align, the

blade is upside down. The blade should fit snugly and the screws should slot in vertical/perpendicularwith

the blade screw holes.

5. Secure the blades with 3 blade screws, and ensure that the 3 blade screws are tightened at the same time.

Do not tighten on screws first, and do not over tighten the screws as this can damage the blades. Repeat

this process for all blades. Fig.6

Fig.6

6. Replace the light plate as describe in step 4 and secure with screws as shown in Fig.7.

Fig.7

7. Insert and secure the light bulbs into the ES sockets as shown in Fig.8.

8. Carefully place the glass shade cover over the lamp and twist clockwise to lock it. The glass shade must

be inserted correctly before you can lock it in, so check the locking mechanism when performing this task.

Fig.9

Figure 8 Figure 9

WIRING

The wiring can now be installed ready for connection to the terminal block in the ceiling canopy of the fan.

Wiring requirement at the terminal block:

- Connect main supply Live wire to “L”

- Connect main supply Neutral wire to “N”

- Connect Earth wire to “E”.

NOTE: AN ISOLATION SWITCH SHOULD BE INSTALLED SOMEWHERE IN THE FIXED WIRING OF A

REMOTE FAN IN CASE REMOTE IS LOST, OR FOR SERVICING OF THE FAN.

FINISH THE INSTALLATION

1) Insert the remote receiver in mounting bracket

2) Connect remote to motor wire via plugging the plug and socket together and connect remote to mounting

bracket via plugging the plug and socket together

3) Cover the mounting bracket with the canopy, and secure the canopy via screws.

Fig.10

REVERSE FUNCTION

Your ceiling can operate either in fan mode or reverse fan mode.

SUMMER Mode: The reverse switch shall be in “down” (SUMMER) position to make the fan rotate in the

anticlockwise direction. The airflow will be directed downwards, for cooling in summer.

WINTER Mode: The reverse switch shall be “up” (WINTER) position to make the fan rotate in clockwise

direction. The airflow will be directed upwards, for energy conservation in winter.

HOW TO USE THE FAN/LIGHT WITH REMOTE CONTROL

SETTING DIP SWITCHES

When two or more fans are located near each other, you may desire to have the receiver/transmitter for each

fan set to a different code, so that the operation of one fan does not affect the operation of the other fans.

The DIP switches for the receiver are located on the flat surface of the receiver. The DIP switches for the

transmitter are in the battery compartment. Fig. 11.

NOTE: Ensure that the power to the supply wires has been turned off before setting the code.

NOTE: Before you change the DIP switch settings, make sure the battery is not connected to the transmitter.

Figure 11 Figure 12

Change the position of the DIP switches in the remote transmitter and the receiver. Make sure that the DIP

switches match in theremote receiver and transmitter. If they don’t match, the transmitter will not function. Fig.

ICONS ON THE REMOTE LCD PANEL

Figure 13

Auto mode temperature setting icon

1) Indicate the temperature at which the fan turns on, when the fan is set to FAN AUTO function.

2) Indicate the time at which the fan turns off, when the fan is set to FAN TIMER function.

3) The icon will switch from temperature setting and timer setting every two seconds automatically.

Room temperature setting icon

1) Indicate the room temperature.

2) Indicate the time at which the light turns off, when the light is set to LIGHT TIMER function.

3) The icon will switch from temperature setting and timer setting every two seconds automatically.

Low battery icon

When the battery low icon is flashing, that means battery power level is low, please replace the batteries

immediately.

Fan speed icon

Display the fan setting is at which speed level (high, medium, low, off )

Fan running mode icon

Indicate the fan is set to MANUAL mode or FAN AUTO mode

Lighting status icon

Display the light setting is ON or OFF

BUTTONS ON THE REMOTE

FAN AUTO: Press the button to switch from FAN AUTO mode to MANAUL mode.

FAN: Press the button to set fan running at HIGH – MEDIUM – LOW – OFF speed.

FAN TIMER: Press the button to turn off the fan at setting time automatically.

LIGHT TIMER: Press the button to turn off the light at setting time automatically.

Press and hold the button for 10 seconds to switch from degree Celsius to degree Fahrenheit.

LIGHT DELAY: Press the button to active the light delay function, which will turn off the light 3 minutes later.

Up: Set the temperature and time up

Down: Set the temperature and time down

LIGHT switch: Press the button to turn ON/ OFF the light.

Use the FAN AUTO Function

Press the FAN AUTO button to active FAN AUTO function, and then press the UP/ DOWN buttons to set the

temperature at what you preferred. The fan will run at the HIGH, MEDIUM, LOW or OFF speed automatically

via comparing to room temperature as following:

Room temperature is lower than setting temperature: ------------------> OFF

Room temperature is higher than setting temperature by 0˚ C -------> LOW

Room temperature is higher than setting temperature by 2˚ C -------> MED

Room temperature is higher than setting temperature by 4˚ C -------> HI

Press the FAN AUTO button again to turn off the FAN AUTO function.

Use FAN/ LIGHT TIMER Function

Press the FAN TIMER / LIGHT TIMER buttons to active the timer function, and then press the UP / DOWN

buttons to set the time at what you preferred. The fan and light will turn OFF at setting time.

AFTER INSTALLATION

WOBBLE:

NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE

MOUNTED ON A RUBBER GROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING IT

WOULD CAUSE EXCESSIVE VIBRATION. MOVEMENT OF A FEW CENTIMETRES IS QUITE

ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM.

TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE

MOUNTING BRACKET AND DOWN ROD ARE SECURE.

BALANCING KIT: Balancing Kit is provided to balance the ceiling fan on initial installation. Please refer to the

instruction on how to use the Balancing Kit. The balancing kit can be used to assist re-balancing should the

ceiling fan becomes un-balanced again, so store your balancing kit away after first use.

NOISE:

When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations and

frequency signals superimposed in the electricity for off-peak hot water control, may cause a change in fan

motor noise. This is normal. Please allow a 24-hour “breaking -in” period, most noises associated with a new

fan disappear during the time. The manufacturer’s warranty covers actual faults that may develop and NOT

minor complaints such as hearing the motor run – All electric motors are audible to some extent.

CARE AND CLEANING

1) Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to

avoid scratching the paint finish. Please turn off electricity power when you do so.

2) Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the

possibility of an electrical shock.

3) Motor has permanently lubricated ball bearing. No need to oil

NOTE: Always turn off the power and disconnect thefemale plug 1 and male plug 1 before attempting toclean

your fan.

Inhaltsverzeichnis

Sprachen:

Andere LUCCI Lüfter Handbücher

LUCCI

LUCCI AIRLIE HUGGER 36 Bedienungsanleitung

LUCCI

LUCCI AIRFUSION RESORT Bedienungsanleitung

LUCCI

LUCCI NORDIC Series Service-Handbuch

LUCCI

LUCCI ATLANTA Bedienungsanleitung

LUCCI

LUCCI TAHITIAN SERIES Bedienungsanleitung

LUCCI

LUCCI AIRFUSION TURBO III Bedienungsanleitung

LUCCI

LUCCI AIRFUSION BREEZE Service-Handbuch

LUCCI

LUCCI AIRFUSION AIRLIE ECO SERIES Bedienungsanleitung

LUCCI

LUCCI AIRFUSION AKMANI Betriebsanleitung

LUCCI

LUCCI ARRAY DC Bedienungsanleitung

LUCCI

LUCCI AIRFUSION CAROLINA Bedienungsanleitung

LUCCI

LUCCI Airfusion Aria Service-Handbuch

LUCCI

LUCCI WHITEHAVEN Bedienungsanleitung

LUCCI

LUCCI ABYSS Series Bedienungsanleitung

LUCCI

LUCCI Airfusion Airmover Bedienungsanleitung

LUCCI

LUCCI THERMALITE 3 IN 1 Service-Handbuch

LUCCI

LUCCI AIRFUSION COMMAND II Series Bedienungsanleitung

LUCCI

LUCCI NEWPORT Installationsanleitung

LUCCI

LUCCI AIRFUSION QUEST II Betriebsanleitung

LUCCI

LUCCI FUTURA ECO Leitfaden

LUCCI

LUCCI Futura 48 inch Bedienungsanleitung

LUCCI

LUCCI Airfusion Aria Bedienungsanleitung

LUCCI

LUCCI GRENADA Series Installationsanleitung

LUCCI

LUCCI FIJIAN II Series Service-Handbuch

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung