M-system R30YN16C Bedienungsanleitung
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9012 Rev.2 P. 1 / 4
INSTRUCTION MANUAL
DISCRETE OUTPUT MODULE
(PNP transistor output, 16 points) MODEL
R30YN16C
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Discrete output module.......................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove the terminal block or mount it, turn off
output signals for safety.
■HOT SWAPPABLE MODULES
• It is possible to replace a module with the power supplied
provided that the module is replaced with one with the
same model number and installed in the same base slot.
• Turn off output signals before replacing the module for
safety. Note that replacing multiple modules at once may
greatly change line voltage levels. We highly recommend
to replace them one by one.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
• Be sure to attach the terminal cover for safety.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
■OUTPUT AT THE LOSS OF COMMUNICATION
• Holds the output of the last normally received data.
• “Reset to 0” setting is not available.
R30YN16C
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9012 Rev.2 P. 2 / 4
COMPONENT IDENTIFICATION
RUN
ERR
RUN LED
Output Terminal Block
ERR LED
■FRONT VIEW
■BOTTOM VIEW
■SIDE VIEW
Lock Tab
Base Fixing Screw
Specifications
Positioning Guide
Terminal Cover
1
5
9
13
2
6
10
14
3
7
11
15
4
8
12
16
Discrete Output Indicator LEDs
Terminal Fixing
Screw
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
■STATUS INDICATOR LED
ID COLOR FUNCTION
RUN Green ON in normal host communication
OFF in host communication error
ERR Red OFF when internal bus operates normally
ON when an internal bus error occurs
Discrete Output Green ON when discrete output is ON
OFF when discrete output is OFF
■TERMINAL ASSIGNMENTS
11
Y9
12
Y10
13
Y11
14
Y12
15
Y13
16
Y14
17
Y15
18
Y16
19
V+
20
V–
1
Y1
2
Y2
3
Y3
4
Y4
5
Y5
6
Y6
7
Y7
8
Y8
9
V+
10
V–
NO. ID FUNCTION NO. ID FUNCTION
1 Y1 Output 1 11 Y9 Output 9
2 Y2 Output 2 12 Y10 Output 10
3 Y3 Output 3 13 Y11 Output 11
4 Y4 Output 4 14 Y12 Output 12
5 Y5 Output 5 15 Y13 Output 13
6 Y6 Output 6 16 Y14 Output 14
7 Y7 Output 7 17 Y15 Output 15
8 Y8 Output 8 18 Y16 Output 16
9 V+ 24V DC 19 V+ 24V DC
10 V– 0V 20 V– 0V
R30YN16C
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9012 Rev.2 P. 3 / 4
INSTALLATION
■INSTALLATION TO THE BASE
Use the Installation Base (model: R30BS).
The I/O slots are numbered in the ascending order starting
from the one on the immediate right side of the network
module (slot 1, slot 2...).
A code indicating the I/O slot number is assigned to each
I/O slot and I/O data is allocated in the order of this codes.
When an I/O slot is vacant, blank data is sent or received to/
from the PLC, etc.
PWR COM I/O1 I/O n
■HOW TO MOUNT THE MODULE
1) Engage the positioning guide of the module with the In-
stallation Base.
2) Pivot the module on the positioning guide and press it
down until the lock tab clicks into place.
Positioning Guide
3) Tighten the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more) (torque 0.5 N·m).
Base Fixing Screw
■HOW TO REMOVE THE MODULE
1) Loosen the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more).
Base Fixing Screw
2) While pressing the projection on the lock tab, push the
module upward.
3) Detach the positioning guide of the module from the In-
stallation Base.
Lock Tab
R30YN16C
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9012 Rev.2 P. 4 / 4
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
①
②
③
④
⑪
⑫
⑬
⑭⑤
⑥
⑦
⑧
⑨
⑩
⑮
⑯
⑰
⑱
⑲
⑳
110 (4.33)
25 (.98) 98 (3.86)
20–M3
SCREW
6
(.24)
■CONNECTION DIAGRAM
3
1
4
2
5
6
7
8
19
13
14
12
15
16
17
18
9
10
20
11
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
Y10
V+
V+
Y11
Y12
Y13
Y14
Y15
Y16
V–
V–
+–
V+
V+
V–
V–
1
10
20
9
18
19
Y1
Y16
■ Output Connection Example
+–
INTERNAL
BUS
INTERNAL
POWER
BUS CONNECTOR
WIRING INSTRUCTIONS
■TIGHTENING TORQUE
Separable screw terminal wiring screw: 0.5 N·m
Separable screw terminal fixing screw: 0.5 N·m
■SOLDERLESS TERMINAL unit: mm (inch)
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solder-
less terminals with insulation sleeve do not fit.
Applicable wire size: 0.25 to 0.75 mm2
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd., Nichifu Co., Ltd.
3.2 (.13) dia.
12 (.47) max.
6 max.
(.24)
3 (.12) max.
■HOW TO REMOVE SEPARABLE SCREW TERMINAL
The terminal block is separable in two pieces. Evenly loos-
en two screws on top and bottom of the terminal block to
separate.
Andere M-system E/A-System Handbücher
M-system
M-system M5SN Bedienungsanleitung
M-system
M-system R3-CT8C Bedienungsanleitung
M-system
M-system R7I4DML3-DC32A Bedienungsanleitung
M-system
M-system R3-RS8B Bedienungsanleitung
M-system
M-system R7L-RS4-R Bedienungsanleitung
M-system
M-system R3-DC64A Bedienungsanleitung
M-system
M-system R7ML-RS4 Bedienungsanleitung
M-system
M-system R3Y-RS8 Bedienungsanleitung
M-system
M-system R7 Series Bedienungsanleitung
M-system
M-system R7F4DD-DC16B-C Bedienungsanleitung
M-system
M-system R80DAT16A2 Bedienungsanleitung
M-system
M-system R7M-DA16-R Bedienungsanleitung
M-system
M-system R7D-TS4 Bedienungsanleitung
M-system
M-system R30US4 Bedienungsanleitung
M-system
M-system R7L-EA8 Bedienungsanleitung
M-system
M-system R3-TS8 Bedienungsanleitung
M-system
M-system R7 Series Bedienungsanleitung
M-system
M-system R7 Series Bedienungsanleitung
M-system
M-system R7L-DC16B Bedienungsanleitung
M-system
M-system Devicenet R7F4HD-DA32B Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
